机载SAR成像对瞄准线运动补偿的要求

飞机偏离匀速直线运动的运动误差是机载合成孔径雷达成像的基本困难之一。通过详细的理论推导,给出了当飞机沿瞄准线方向同时存在恒定速度误差,恒定加速度误差和正确弦摆动速度误差时,以回波信号压缩波形的主瓣偏移,二次相位误差,三次相位误差以及积分旁瓣比等ＳＡＲ系统图像质量指标的最大允许值表示的机载正侧视ＳＡＲ运动补偿定量要求的解析式。并结合一例子进行了计算分析,所得结论可供有关人员参考。     

In-Flight Parity Vector Compensation for FDI

The performance of a failure detection and isolation (FDI) algorithm applied to a redundant strapdown inertial measurement unit (IMU) is limited by sensor errors such as input axis misalignment, scale factor errors, and biases. A techique is presented for improving the performance of FDI algorithms applied to redundant strapdown IMUs. A Kalman filter provides estimates of those linear combinations of sensor errors that affect the parity vector. These estimates are used to form a compensated parity vector which does not include the effects of sensor errors. The compensated parity vector is then used in place of the uncompensated parity vector to make FDI decisions. Simulation results are presented in which the algorithm is tested in a realistic flight environment that includes vehicle maneuvers, the effects of turbulence, and sensor failures. The results show that the algorithm can significantly improve FDI performance, especially during vehicle maneuvers.     

激光陀螺捷联惯导系统旋转调制技术综述

激光陀螺旋转调制技术是一种系统级误差自补偿技术，能够有效调制陀螺和加速度计的误差，提高导航系统的精度。首先分析了旋转调制型捷联惯导系统的基本原理和类型，然后从转位方案的编排、惯性测量单元旋转速度和转停时间的选取、旋转机构的导航解算、旋转机构的误差分析、载体角运动隔离等多方面，对激光陀螺旋转调制技术进行了综述，并探讨了我国旋转调制技术的重点研究方向，提出了合理的建议。     

运动补偿用惯性器件误差对SAR成像分辨率的影响研究

 为提高合成孔径雷达（SAR）系统的性价比，必须根据SAR成像分辨率的要求和整体系统参数，设计相应精度的运动补偿用捷联惯导系统。在确定SAR运动补偿系统方案和安装方式的基础上，分析不同方向的加速度计和陀螺仪误差对天线相位中心位置测量误差的影响，并利用位置测量误差与SAR成像分辨率之间的关系，进一步明确了不同方向的加速度计和陀螺仪对SAR成像分辨率的影响。研究表明：基于SAR的工作原理和安装方式，x方向加速度计和y方向陀螺仪对SAR成像分辨率的影响明显比其他惯性器件严重；相同误差水平的惯性器件对SAR成像分辨率的影响随着合成孔径时间和工作波长的不同而不同，时间越长，波长越短，影响则越严重。SAR成像仿真证明了结论的正确性。研究结果对于研制高性价比SAR成像运动补偿系统有一定的理论指导意义。     

基于FPGA的捷联惯组数据采集系统设计与实现

惯性器件性能的好坏直接决定了武器系统的性能,惯性器件的测试工作需要专门的脉冲采集系统来实现,本文介绍了一种基于FPGA的新型惯组脉冲采集系统,通过选用XC3S1000-4FGG676I芯片轻松实现了多路脉冲信号、交直流电压量以及温度传感器信号采集,抗干扰措施的采用有效地保证了该系统的稳定性和可靠性,经过大量的试验考核目前已经正式运用于捷联惯组的单元测试过程中。     

Inner Attitude Integration Algorithm Based on Fault Detection for Strapdown Inertial Attitude and Heading Reference System

This article proposes a new inner attitude integration algorithm to improve attitude accuracy of the strapdown inertial attitude and heading reference system(SIAHRS), which, by means of a Kalman filter, integrates the calculated attitude from the accelerometers in inertial measuring unit(IMU), called damping attitudes, with those from the conventional IMU. As vehicle's acceleration could produce damping attitude errors, the horizontal outputs from accelerometers are firstly used to judge the vehicle's motion so as to determine whether the damping attitudes could be reasonably applied. This article also analyzes the limitation of this approach. Furthermore, it suggests a residual chi-square test to judge the validity of damping attitude measurement in real time, and accordingly puts forward proper information fusion strategy. Finally, the effectiveness of the proposed algorithm is proved through the experiments on a real system in dynamic and static states.     

基于组合导航技术的光纤捷联系统在线标定

 将光纤捷联系统惯性测量单元（IMU）输出误差分解成零偏误差、标度因数误差、失准角误差和随机白噪声几个部分,建立了系统误差模型,基于此模型设计卡尔曼滤波器引入高精度外部信息源对IMU进行在线标定。将此方法应用于某光纤捷联系统进行跑车试验,结果表明：引入外部信息源进行在线标定与补偿后系统纯惯导精度显著提高,本文建立的系统误差模型和在线估计方式有效估计了IMU输出误差,实现了系统在线标定,提高了系统实用精度。     

MOTION COMPENSATION FOR HIGH RESOLUTION AIRBORNE SAR WITH IMU & GPS

Ｔｈｅｅｒｏｒｂｅｔｗｅｅｎａｃｔｕａｌａｎｄｎｏｍｉｎａｌｆｌｉｇｈｔｐａｔｈｓｏｆｔｈｅａｎｔｅｎｎａｐｈａｓｅｃｅｎｔｅｒ（ＡＰＣ）ｉｓｄｅ－ｆｉｎｅｄａｓｔｈｅｐｌａｔｆｏｒｍｍｏｔｉｏｎｅｒｏｒ．Ｕｎｃｏｍｐｅｎ－ｓａｔｅｄＡＰＣｍｏｔｉｏ...     

改进的容错惯性导航系统

 用于余度捷联惯性测量单元(IMU)的故障检测及分离(FDI)方法的性能受到诸如输入轴不准,刻度因子误差以及偏倚这样的传感器误差的限制。本文采用分离偏倚估计方法以获得上述影响奇偶向量的传感器误差的线性组合的估计,然后将这些估计用于构成补偿的奇偶向量,该奇偶向量不包括传感器误差的影响。用经补偿的奇偶向量代替未经补偿的奇偶向量进行故障检测及分离判决以提高FDI的性能。仿真结果表明奇偶向量补偿算法可大大提高FDI的性能,特别是在飞行器做机动飞行时。     

An algorithm for astro-inertial navigation using CCD star sensors

A self-contained suite of astro-inertial navigation system is capable of autonomous mission and is operationally reliable. The typical astronavigation system (ANS) makes use of star-trackers, which are expensive and complex. To make the system cost effective and less complex, the star-tracker is replaced by a charge coupled device (CCD)-based star sensor, rigidly mounted on a strapdown inertial measurement unit (SIMU) of the system. This electro-optical star sensor is compact and easy to use with an ANS that utilizes efficient star identification techniques. This paper designs an algorithm that estimates axes misalignment angles of strapdown inertial navigation system (SINS) that makes stars' observations utilizing a CCD star sensor. Mathematical modeling of the suggested scheme was carried out and transformations between different frames were exercised. From the image projection geometry, stars' right ascensions and declinations, relative to the body frame, were estimated. Lastly, from the known stars' position vectors in mathematical platform and reference frames, axes misalignment matrix representing SINS attitude errors can be estimated employing the derived relationship.     

激光捷联惯组减振系统设计计算及试验研究

以某型号激光捷联惯组减振系统为设计对象,详细论述了激光捷联惯组减振系统的设计过程,并进行了相关试验验证,结果表明理论计算和试验结果比较一致.研究结果对惯性系统减振系统的设计具有一定的参考意义.     

旋转式SINS的自标校技术研究

惯性器件常值及慢变误差是影响捷联惯导系统精度的主要因素之一,所以在捷联惯导系统出厂前需要对常值及慢变误差参数进行标定。但这些误差参数会随时间发生变化,对于高精度捷联惯导系统,每次启动后需要对惯性器件的误差参数进行重新标校。针对光纤惯导系统,建立了IMU误差模型,并根据提出的旋转式捷联惯导系统自标校转位方案原则设计出了一种8位置自标校方案,对惯性器件标定参数进行激励和辨识,并建立了Kalman滤波状态方程及量测方程,对惯导系统误差参数进行在线标定。实验结果表明,该方案对其惯性器件误差参数能进行准确估计,具有一定的参考价值。     

高分影像辅助下的航空高光谱严密几何检校方法

 惯性测量单元(IMU)与传感器视准轴的偏心角和偏心矢量是造成航空线阵列高光谱数据几何校正误差的主要原因之一。在分析偏心角与偏心矢量误差来源之后提出该误差由IMU主轴与传感器主轴的角度偏差、测区固定偏差、GPS中心与传感器投影中心相对偏差组成,在此基础上建立了较为严密的检校模型。针对模型解算时需要大量高精度控制点的问题,提出了一种高分影像辅助下的亚像元精度控制点自动提取方法。通过多地区、多传感器高光谱航测实验表明,亚像元精度控制点能有效提高模型解算精度。新检校模型可获得亚像元校正精度,推扫式传感器——应用型机载成像光谱仪(AISA)建模中误差约为0.39个像元,摆扫式传感器——实用型模块化成像光谱仪(OMIS)建模中误差约为0.23个像元,校正后的影像可直接进行拼接。     

Fiber-optic strapdown inertial system with sensing cluster continuous rotation

This research describes a technique and a performance analysis of a fiber-optic strapdown inertial system with sensing cluster continuous rotation around the vertical body axis of the vehicle. The bias errors of these inertial sensors, gyros and accelerometers with cluster rotation, will have periodically varying corresponding components along the body axes. The modulated sensor errors produce reduced system errors. Simulation results indicate that, compared with the conventional method, the proposed approach attenuates the navigation errors and alignment errors due to the gyros' error and the accelerometers' error.     

一种常规机动下机载SINS/GPS组合导航系统的可观测性分析

为保证机载捷联惯组的导航精度能够达到要求,需要对惯组定期进行返厂标定,成本高、周期长,也影响载机的使用效率,故而机载惯组在线标校技术的研究一直在不断进行中。对大中型运输机的机载惯组而言,由于其机体较大、机动能力较差,很难完成诸如S机动等复杂的机动动作,故而需要对其常规飞行机动状态下机载SINS/GPS组合导航系统的可观测性进行分析。利用GPS提供的速度和位置信息作为外部观测量来设计Kalman滤波器,采用基于分段线性定常系统(PWCS)的奇异值分解法(SVD),对飞机静止、起降、匀速飞行、匀加减速飞行、转弯等一系列常规机动条件下系统的可观测性和可观测度进行研究。通过Matlab仿真和转台实验,验证了组合导航系统可观测性分析结论的有效性,可为机载惯组的在线标校提供一定参考。     

Propagation and System Accuracy Impact of Major Sensor Errors on a Strapdown Aircraft Navigator

A strapdown system is considered as an unaided inertial navigator aboard an aircraft. Presented here are simulation results detailing the propagation of navigation errors (in nautical miles) due to strapdown sensor errors for four trajectories. They indicate the type of performance that can be expected from a strapdown system utilizing good ?off the shelf? gyros and accelerometers, and dramatically illustrate the improvements necessary in these components to obtain navigation performance comparable to that available from a good gimballed inertial system. The total navigation error for each trajectory is broken down to show the contribution from each of the various error sources. This breakdown quickly reveals which are the critical error sources for a given trajectory class, and also points up the relationship that exists between each individual error source, aircraft maneuvers, and the resulting navigation error. Several of the error mechanisms are discussed at length and a set of linearized differential equations which can be used to analyze error propagations is presented. These results should be of particular interest to the system designer who is faced with the problem of specifying the sensor error parameters necessary to meet mission performance requirements. With an analysis similar to the one presented here, but structured around his own expected mission trajectories, the designer should be able to confidently predict system accuracies and intelligently perform tradeoffs on the critical system parameters.     

Development of a low-cost integrated GPS/IMU system

This paper describes the development of a low-cost and small size integrated Global Positioning System (GPS)/inertial measurement unit (IMU). The developed strapdown Attitude and Heading Reference System (AHRS) is capable of providing attitude and heading accuracy at ±0.2 and ±0.4 degrees, respectively. The prototype of low-cost integrated GPS/IMU can give positioning accuracy of 10 metres     

捷联惯导系统误差特点分析

对捷联惯导系统的误差源进行了深入分析,结果表明当陀螺仪刻度系数误差较大时,捷联惯导系统定位误差闭合现象较明显,即飞机返场时,误差有明显减小的现象;分析了舒拉调谐周期对惯导系统位置误差的影响并进行仿真,仿真结果验证了舒拉调谐对误差的调制作用,即在舒拉周期振荡分量的影响下,惯导系统的累积误差在某段时间内存在误差减小现象。     

Advanced Development of ESG Strapdown Navigation Systems

The fundamental problem of inertial navigation, double integration of acceleration to obtain position, is defined and discussed. Mechanizations of both space-stable and local-vertical platform systems are exhibited. The synthesis problem for an electrically suspended gyro (ESG) strapdown system is defined and discussed: readout, readout errors due to vehicle motion, synchronization of readout with system computer, alignment, correction and calibration for mass unbalance drift, and digital mechanization. Alignment, calibration, and acceleration measurement are also discussed. Sources of error involved in the electronic gimbaling including those peculiar to strapdown configuration are discussed and compared to mechanically gimbaled systems. Advanced developments required in the component and systems areas are listed, and it is shown that such development will lead to reduced complexity, higher accuracy, and increased reliability and utility for inertial systems.     

激光陀螺惯性导航系统旋转技术综述

旋转技术能够有效调制激光陀螺和加速度计的误差,提高惯性导航系统的精度。首先基于惯性测量单元的误差模型,分析了旋转技术的基本原理。然后对旋转技术的旋转方案、最优转动速率、旋转机构误差对系统精度的影响、载体角运动对旋转效果的影响、采用旋转技术的惯导解算、采用旋转技术的初始对准与测漂等进行了综述,探讨了我国研究旋转技术的重点研究方向,为开展我国旋转式光学陀螺惯导系统的研究提供了一定参考。