共查询到16条相似文献,搜索用时 125 毫秒
1.
2.
自动铺带成型压力控制技术 总被引:6,自引:2,他引:4
通过对自动铺带成型工艺过程的分析,论述自动铺放过程是成型压力作用下预浸带蠕变及回复的连续动态过程。经对预浸带蠕变过程分析,采用分阶段适应性调节铺带头压力的方法保持成型压力恒定,以保证预浸带在铺放后厚度均匀。结合自动铺带CAM软件,提出一种基于铺带轨迹控制点的分段调节铺带头成型压力的控制算法,并采用UMAC (Universal Motion and Automation Controller)控制系统设计相应的控制程序,最终实现成型压力分阶段调节子控制系统的搭建。 相似文献
3.
4.
5.
6.
7.
复材构件手工成型时,预浸带经剪裁后手工铺叠、压实到模具表面.随着复材构件在现代大型飞机上广泛应用,人工铺放工艺已难以满足实际需要,急需自动铺带技术来提高生产效率,改善制造过程的可控制性,降低成本以及提高产品质量.
自动铺带技术利用数控技术实现预浸带剪裁、定位、铺叠的自动化.与手工相比,自动铺带技术可降低制造成本30%~50%,主要适用于各种大尺寸、小曲率部件的制造. 相似文献
8.
通过分析预浸带/纱在曲面上的铺放工艺性,提出以轨迹测地曲率作为铺放工艺性测度,构建一种基于结构设计的自调节轨迹规划算法,兼顾自动铺放中的铺放工艺性和结构设计要求.该算法是在满足结构设计的前提下,将预浸带/纱轨迹从结构设计所确定的方向按特定方式向测地线方向偏转,从而减小预浸带/纱的变形.本文以固定角度法作为结构设计准则、以最大容许偏转角法定义修正函数,以此为例阐述具体算法及实施过程.基于Visual C++平台,进行C++和SQL混合编程,以某型进气道为模型进行了算法仿真,并进行了进气道和锥壳的铺放试验.结果表明:容许偏转角的增大有助于缓解预浸带/纱的变形. 相似文献
9.
《航空科学技术》2016,(11)
为了研究自动铺放过程中预浸料层间粘结性能与铺放工艺的关系,自行设计了一套模拟高速铺放过程的预浸料粘结性能测试系统,采用自动铺放和剥离实验分开进行的"两步法"作为粘结性能的测试方法。利用该测试方法研究了CCF300/BA9916-2环氧树脂预浸料的自动铺放粘结性能工艺特性,采用单因素实验,研究了不同铺放工艺参数对预浸料层间粘结性能的影响规律,并运用正交实验,确定了各铺放工艺参数对预浸料层间粘结性能的影响程度。实验结果表明,预浸料层间粘结性能随着铺放压力和铺放温度的增大而增大,随着铺放速度的增大而减小。铺放温度对预浸料层间粘结性能影响最为显著,其次为铺放压力,铺放速度影响最小。 相似文献
10.
11.
针对气动加热条件下光学窗口辐射导热耦合传热开展研究,以了解光学窗口的热辐射发射规律及热防护性能。采用有限体积法、蒙特卡罗法、谱带模型建立了具有镜反射界面的光学窗口辐射传输及辐射导热耦合传热计算模型,对具有两层SiO2玻璃的光学窗口传热特性进行了模拟。结果表明处于高温区玻璃向外发射热辐射,低温区玻璃吸收热辐射;除了加热面附近外的玻璃区域,辐射热流密度远大于导热热流密度,在2.9~4.2μm谱带内的辐射热流密度大于0.4~2.9μm谱带内的;在0.4~2.9μm谱带内,可见光波长内的出射辐射热流密度最小,中红外波长范围内出射辐射热流密度最大。在光学窗口总厚度一定的情况下,降低玻璃层厚度和玻璃夹层气体热导率能够有效降低光学窗口非加热面稳态温度。 相似文献
12.
13.
本文提出了联立求解二维可压缩边界层方程组和稳定导热方程的迭代法,从而修正了文献[1]假定物体表面温度等于来流总温的局限;同时提供了用这种方法计算气冷叶片表面局部对流换热系数的完整的FORTRAN程序。文中用近似积分法求解边界层方程组,用有限元素法计算叶片的稳定温度场。算例的结果与有关的理论及实验结果相接近。 相似文献
14.
15.
16.
Investigation of the infrared characteristics of a rocket nozzle is very important for the study of infrared initiating technology. The Narrow-Band Zone model is developed for that purpose. The spectral transmission and absorption factors are introduced, and the equations between radiative heat flux and the temperature of waill surfaces and gas are developed. The radiative heat transfer in one axisymmetric cylindrical enclosure filled with homogeneous radiative participating medium is computed with the Narrow-Band Zone model and compared with those in the reference documents. The comparison shows good agreement. The radiative heat transfer to the nozzle of one rocket engine is also calculated with the Narrow-Band Zone model, and the outgoing radiative energy flux and energy rate integrated in a mid-wave infrared band 2-6 pm, a long-wave infrared band 8-14 pm and the full wave band are analyzed. The following conclusions can be derived: the spectral radiation from the inlet and outlet of the nozzle show apparent spectral discontinuity, which appears greater in the 2.7-2.95 pm than in the neighboring wave band. The spectral outgoing radiative energy flux of nozzle wail is similar to that of gray body, which decreases with wavelength in 2-14 pm. The outgoing radiative energy flux on the nozzle wall is greater in the cylindrical and contracting section of nozzle, but smaller in the divergent section, which is determined by temperature. The nozzle of the rocket engine radiates most energy in the mid-wave surfaces by absorption. The most important feature of gas radiation is the strong selection of the waveband, so the detailed study of the infrared characteristics of nozzle of the rocket engine should be carried out on narrow-band computation. 相似文献