共查询到16条相似文献,搜索用时 328 毫秒
1.
《航空科学技术》2016,(11)
为了研究自动铺放过程中预浸料层间粘结性能与铺放工艺的关系,自行设计了一套模拟高速铺放过程的预浸料粘结性能测试系统,采用自动铺放和剥离实验分开进行的"两步法"作为粘结性能的测试方法。利用该测试方法研究了CCF300/BA9916-2环氧树脂预浸料的自动铺放粘结性能工艺特性,采用单因素实验,研究了不同铺放工艺参数对预浸料层间粘结性能的影响规律,并运用正交实验,确定了各铺放工艺参数对预浸料层间粘结性能的影响程度。实验结果表明,预浸料层间粘结性能随着铺放压力和铺放温度的增大而增大,随着铺放速度的增大而减小。铺放温度对预浸料层间粘结性能影响最为显著,其次为铺放压力,铺放速度影响最小。 相似文献
2.
3.
4.
5.
6.
为系统建立可表征刚度与黏性的预浸料剥离模型,构建探针、拉伸与剥离相结合的试验验证系统。首先,设计用于预浸料的移动悬臂剥离装置,完成各工艺参数下预浸料黏性和动态刚度的90°剥离试验测定,并建立剥离仿真模型;然后,通过探针试验获取黏性参数,采用内聚力模型定量表征黏性参数;接着,通过拉伸、压缩试验测定预浸料的正交各向异性力学参数,连同探针试验获得的黏性参数一同输入到剥离模型中,在各个工艺参数下黏性和刚度的仿真结果与试验值吻合程度良好;由于仿真与试验揭示剥离脱辊现象会影响剥离力测定值,因此研究脱辊现象及其机理,发现将导辊半径设计在3~7 mm内,可减弱脱辊程度、提高剥离试验的准确性。为系统测定并表征预浸料黏性及刚度、预浸料建模、开展自动铺放仿真等提供了参考。 相似文献
7.
基于探针试验的预浸料黏性内聚力模型 总被引:1,自引:1,他引:0
以预浸料黏性为研究对象,通过探针试验,研究了预浸料铺放过程中预浸料与模具之间的脱粘失效行为及其随铺放工艺参数的变化规律。试验中发现铺放速率、压力和温度对预浸料黏性行为影响显著,且存在界面失效(低温)和内聚失效(高温)两种失效模式。针对这一现象,采用指数内聚力模型(CZM)表征了预浸料的黏性行为,利用该模型描述了不同铺放温度下粘结层应力快速上升、损伤扩展和最终失效的脱粘过程,定量地给出了黏性CZM参数与铺放工艺参数之间的关系。研究结果表明,预浸料粘结强度和特征位移均随铺放速率增加而近似线性减小,均随铺放压力增加而近似线性增大。随铺放温度的增加,黏性CZM参数先增大后减小,近似呈二次关系。为制定特定铺放条件下的铺放工艺规划提供参考。 相似文献
8.
通过分析预浸带/纱在曲面上的铺放工艺性,提出以轨迹测地曲率作为铺放工艺性测度,构建一种基于结构设计的自调节轨迹规划算法,兼顾自动铺放中的铺放工艺性和结构设计要求.该算法是在满足结构设计的前提下,将预浸带/纱轨迹从结构设计所确定的方向按特定方式向测地线方向偏转,从而减小预浸带/纱的变形.本文以固定角度法作为结构设计准则、以最大容许偏转角法定义修正函数,以此为例阐述具体算法及实施过程.基于Visual C++平台,进行C++和SQL混合编程,以某型进气道为模型进行了算法仿真,并进行了进气道和锥壳的铺放试验.结果表明:容许偏转角的增大有助于缓解预浸带/纱的变形. 相似文献
9.
10.
自动铺带成型压力控制技术 总被引:6,自引:2,他引:4
通过对自动铺带成型工艺过程的分析,论述自动铺放过程是成型压力作用下预浸带蠕变及回复的连续动态过程。经对预浸带蠕变过程分析,采用分阶段适应性调节铺带头压力的方法保持成型压力恒定,以保证预浸带在铺放后厚度均匀。结合自动铺带CAM软件,提出一种基于铺带轨迹控制点的分段调节铺带头成型压力的控制算法,并采用UMAC (Universal Motion and Automation Controller)控制系统设计相应的控制程序,最终实现成型压力分阶段调节子控制系统的搭建。 相似文献
11.
Lei ZU Xianzhao XIA Qian ZHANG Xiaolong JIA Huabi WANG Guiming ZHANG Jinhu LU 《中国航空学报》2022,35(4):438-449
This paper tested the viscosity of prepreg in the automatic placement process, and conducted the probe and placement-90° peel tests through the test systems. The law of variation of prepreg viscosity during the laying process was studied through these tests under different conditions by taking the peel force to intuitively and quantitatively characterise the viscosity of the prepreg.The results show that this viscosity is inversely proportional to the laying rate, proportional to the laying pres... 相似文献
12.
李勇%肖军%还大军%文立伟 《宇航材料工艺》2008,38(5)
提出了一种基于两步法的复合材料锥壳螺旋向铺层自动铺带的成型方法,对锥壳螺旋向铺层几何原理进行了分析并对预浸带的预切割进行了设计和验证,对预切割装置进行了原理方案设计并利用CATIA软件进行了自动铺带验证。结果表明:两步法锥壳螺旋向铺带成型技术方案合理可行,预切割装置可以实现预浸带的切割、转录,采用通用铺带头即可以完成螺旋向铺层的自动铺带过程,采用锥壳等厚度铺叠、均匀加压和降低废料率等措施,大大提高制品质量并降低了构件加工成本。 相似文献
13.
14.
15.
In the process of composite prepreg tape winding, the compaction force could influence the quality of winding products. According to the analysis and experiments, during the winding process of a rocket motor nozzle aft exit cone with a winding angle, there would be an error between the deposition speed of tape layers and the feeding speed of the compaction roller, which could influence the compaction force. Both a lack of compaction and overcompaction related to the feed-ing of the compaction roller could result in defects of winding nozzles. Thus, a flexible winding sys-tem has been developed for rocket motor nozzle winding. In the system, feeding of the compaction roller could be adjusted in real time to achieve an invariable compaction force. According to exper-iments, the force deformation model of the winding tape is a time-varying system. Thus, a forgetting factor recursive least square based parameter estimation proportional-integral-differential (PID) controller has been developed, which could estimate the time-varying parameter and control the compaction force by adjusting the feeding of the compaction roller during the winding process. According to the experimental results, a winding nozzle with fewer voids and a smooth surface could be wounded by the invariable compaction force in the flexible winding system. 相似文献