Multi-h CPM遥测信号的定时频率联合估计技术

针对Multi-h CPM（Multi-h Continue Phase Modulation,多指数连续相位调制）遥测接收机的符号定时和载波频率同步问题,在分析MLSD（Maximum-likelihood Sequence Detection,最大似然序列检测）度量值是符号定时偏差和频率偏差的凸函数的基础上,提出一种基于迟/早门和升/降频门的符号定时和频率同步联合估计算法,通过似然值比较,对符号定时偏差和频率偏差进行迭代估计;并对该算法进行仿真,得到不同参数下的同步性能,给出同步参数选择建议.仿真结果表明：将该算法应用到Multi-h CPM遥测系统中,可实现低信噪比信号的快捕和高精度同步.     

一种组合的8PSK差分前向频率估计

考察2种差分前向估计器(DFE)在8PSK系统载波恢复中的性能:基于8 th Power算法的DFE将噪声放大了18dB,恶化了估计性能,但该算法稳健性好;基于模π/4算法的DFE在复高斯噪声的情况下求模运算引入了错误相位点,若能纠正这些错误相位点,则该算法估计精度高。综合2种算法的优点,提出一种组合式的频率估计方案。仿真结果表明,该方案有效纠正了模π/4算法求模运算引入的错误相位点,估计精度高,估计结果稳定可靠。     

基于稀疏表示的双基地MIMO雷达多目标定位及幅相误差估计

 基于稀疏表示理论,提出一种新的双基地多输入多输出(MIMO)雷达收发角度及幅相误差估计算法。利用接收数据,分别构造发射和接收协方差矩阵,并以列向量化后的发射和接收协方差矩阵为量测信号建立2个一维稀疏线性模型,构造模型求解的 L₂-L₁ 混合范数优化目标函数,通过交替迭代寻优获得目标角度估计和幅相误差估计,最后给出了本文算法的收敛性分析。与现有算法相比,该算法充分利用了目标发射和接收空域的稀疏特性,且能够通过对噪声功率的预估计来抑制噪声。仿真结果表明:在低信噪比(SNR)条件下,本文算法仍能够得到较好的估计精度,且对幅相误差具有一定的稳健性。     

GPS多径信号的自适应滤波估计方法

 研究全球定位系统(GPS)多径信号估计的问题。通过分析自适应滤波器的原理,建立了数字中频信号处理的数学模型,提出一种用自适应滤波实现GPS多径幅度、码相位和载波相位估计的方法。该方法采用不同延迟的伪随机序列对信号进行解扩、解调和累加,得到了作为期望信号的系列自适应滤波相关值。对该方法与其他3种方法进行了理论上的分析比较,得出本方法具有信噪比高、自适应滤波性能好、带有码相位信息和不存在载波模糊度问题等优点。根据各种滤波器算法的特点和本应用的需求,给出了选用递归最小二乘算法实现的方法。通过计算机仿真,验证了提出的方法能够在14 dB的信噪比下,以1个采样间隔的时间延迟分辨率和0.005周的载波相位估计精度估计出GPS L1的多径信号。     

高动态下惯性加速度辅助三阶锁相环性能分析

针对高阶跟踪环路稳定性比低阶环路差,大带宽带来测量误差大的问题。研究在高动态环境下,惯导加速度信息辅助卫星接收机三阶载波锁相环跟踪算法,以及不同环路参数下跟踪环路的性能。对载体高动态场景、加速度信息延迟进行建模,并对算法进行了数学仿真。仿真分析结果表明,在加速度信息辅助下,即使压缩载波跟踪环路等效噪声带宽到3Hz,在高达1200g/s的加速度动态下,环路跟踪同样稳定可靠。     

Turbo乘积码编译码算法研究

介绍了基于Chase算法[1,3]的Turbo乘积码软入软出(SISO)迭代译码算法。对Turbo乘积码在加性高斯白噪声(AWGN)信道下的性能进行了仿真和分析,结果表明:Turbo乘积码译码复杂度较低,在编码效率较高时,仍具很好的译码性能。     

极弱信号环境下GPS位同步和载波跟踪技术

为解决环路未锁定、无法找出正确的导航数据位跳变点时极弱全球定位系统(GPS)信号跟踪问题,通过分析信号跟踪模型和相关器1 ms采样数据特性,将最优路径动态规划算法应用于GPS位同步,并提出基于平方根无迹卡尔曼滤波(SRUKF)和位同步结合的载波联合跟踪算法。建立了适合位同步的SRUKF载波环参数估计模型,针对位同步的实现条件和无相位频率先验信息的情况,将位同步模块提前,研究设计了环路未锁定时串行和并行两种弱信号跟踪方案。位同步跟踪完成后环路采用单独的SRUKF工作方式。实验结果证实该文提出的算法具有较高的数据位边缘检测概率(EDR)和参数估计性能,而无须关心环路是否处于锁定状态,能够对载噪比低至22 dB/Hz的弱信号实现跟踪。     

一种低复杂度的极低信噪比高动态信号载波粗捕获算法

 针对传统的时域匹配平均周期图算法计算复杂度高的问题,对极低信噪比高动态信号的载波粗捕获算法进行了研究,提出了一种改进的带有补零的频域移位平均周期图算法。该算法采用多速率频域移位运算简化了多支路多普勒变化率匹配,与原算法相比,其计算复杂度降低倍数为匹配支路数与补零倍数之比,捕获性能几乎不损失。给出了算法中影响捕获性能与计算复杂度的关键参数设计方法。在信噪比(SNR)为－41 dB(载噪比C/N₀=18 dBHz)、载波多普勒频偏为－300～300 kHz、多普勒变化率为－800～800 Hz/s、码速率为20 bps条件下对两种算法进行了仿真,结果表明在基本满足后级载波跟踪需求条件下,即频偏精度均达±12 Hz时,多普勒变化率精度均达±25 Hz/s,捕获概率都在90%以上时,改进算法捕获时间比原算法增加了8%,计算复杂度降低了70%。     

基于数字高速数据解调的Trellis-Coded MPSK与载波相位噪声

本文基于一种数字解调系统分析了在AWGN信道中载波相位噪声对Trellis-Coded MPSK的影响。同时利用存在载波相位噪声条件下的误码率上界公式，运用仿真工具simulink对未编码情况下的QPSK与Trellis-Coded MPSK及级联卷积编码情况下的QPSK与Trellis-Coded MPSK进行了蒙特卡罗仿真。分析结果表明：TCM-8PSK具有较强的载波相位噪声抑制能力。该结果对于进一步研究TCM-8PSK在卫星数传系统中的应用具有重要的参考价值。     

基于滑动DFT和插值DFT算法的GPS信号载波跟踪方法

 在分析GPS接收机跟踪环路信号特征的基础上,将滑动离散傅里叶变换（DFT）算法和插值DFT频率估计算法相结合,提出一种在频域进行的载波跟踪方法。该方法首先根据捕获时得到的粗略载波频率估计值确定计算DFT值点的范围,然后利用滑动DFT算法计算这部分点的DFT值,最后利用插值DFT频率估计算法估计载波频率,进行跟踪环路中载波频率的更新。该方法计算复杂度低,便于实际应用。仿真结果显示,该方法能够对载波频率正确跟踪,验证了算法的可行性。     

Performance analysis of GPS carrier phase observable

The accuracy analysis of Global Positioning System (GPS) carrier phase observable measured by a digital GPS receiver is presented. A digital phase-locked loop (DPLL) is modeled to extract the carrier phase of the received signal after a pseudorandom noise (PRN) code synchronization system despreads the received PRN coded signal. Based on phase noise characteristics of the input signal, the following performance of the first, second, and third-order DPLLs is analyzed mathematically: (1) loop stability and transient process; (2) steady-state probability density function (pdf), mean and variance of phase tracking error; (3) carrier phase acquisition performance; and (4) mean time to the first cycle-slipping. The theoretical analysis is verified by Monte Carlo computer simulations. The analysis of the dependency of the phase input noise and receiver design parameters provides with an important reference in designing the carrier phase synchronization system for high accuracy GPS positioning     

An experimental study of the dual-loop control of electro-hydraulic load simulator （EHLS）

This paper investigates motion coupling disturbance（the so called surplus torque）in the hardware-in-the-loop（HIL）experiments.The＇＇velocity synchronization scheme＇＇was proposed by Jiao for an electro-hydraulic load simulator（EHLS）in 2004.In some situations,however,the scheme is limited in the implementation for certain reasons,as is the case when the actuator＇s valve signal is not available or it is seriously polluted by noise.To solve these problems,a＇＇dual-loop scheme＇＇is developed for EHLS.The dual-loop scheme is a combination of a torque loop and a position synchronization loop.The role of the position synchronization loop is to decouple the motion disturbance caused by the actuator system.To verify the feasibility and effectiveness of the proposed scheme,extensive simulations are performed using AMESim.Then,the performance of the developed method is validated by experiments.     

Maximun Posterion Probability Demodulation of Angle-Modulated Signals

An algorithm is presented for maximum posterior probability (MPP) demodulation of angle-modulated signals. A sampled data version of the problem is considered, in which additive Gaussian noise and Gaussian modulating signal are assumed. The algorithm is a numerical method for solving the nonlinear equations which are necessary conditions for MPP estimation. Results of a simulation of the algorithm are presented and discussed. Improvements in performance with respect to a phaselocked loop appear to stem from use of data before and after the time position of a phase estimate and from optimization of performance at low signal-to-noise ratio (SNR) as well as at high SNR.     

一种低信噪比大多普勒频移下的直扩信号捕获方法

提出了伪码相位一载波频率二维搜索伪码捕获结构在低信噪比大多普勒频移情况下捕获性能恶化的问题，给出了一种中频端简单数字处理算法的解决方案，并分析了该算法的性能。仿真表明，改进的伪码相位一载波频率二维搜索伪码捕获结构在低信噪比大多普勒频移情况下解决了捕获性能恶化的问题。     

Noise analysis of a digital tanlock loop

The noise performance analysis of a nonuniform digital phase-locked loop (DPLL), called the digital tanlock loop (DTL), is investigated by both analytic and computer-simulation methods. The results are presented in terms of phase error probability mass function and mean time to skip cycle versus input signal-to-noise ratio (SNR). These results are compared to the ones obtained with the conventional sinusoidal DPLL loop (DPLL). It is found that, for low-to-moderate input SNR, the DTL has only a slight improvement over the DPLL. The DTL, however, has larger linear characteristics than the conventional DPLL, which makes it attractive for applications that require an increased tracking range or as a first stage in carrier tracking systems based on optimum estimation procedures such as a Kalman smoother     

Double Dither Loop for Pseudonoise Code Tracking

A new type of phase detector for pseudonoise code tracking is introduced and analyzed in comparison with the delay lock loop (DLL) and tau-dither loop (TDL) configurations. It is shown that the double dither loop (DDL) combines the best features of the DLL and the TDL in that the DDL is insensitive to gain and offset imbalances and does not suffer the 3-dB degradation in noise performance typically associated with the TDL. The double dither concept is applicable to other dual channel detectors such as in a Costas-type carrier tracking loop.     

Carrier-Tracking Loop Performance for Quaternary and Binary PSK Signals

By expressing the open-loop response voltage as a Fourier series in terms of the phase-tracking error and then utilizing a very useful mean-value expression, we assess the performance of loops suited to recovering the carrier of four-phase (quaternary) and two-phase (binary) phase-shift-keyed (QPSK and BPSK) signals. At high signal to noise ratios (SNRs) they perform comparably, but at low SNRs the former's performance deteriorates much more rapidly. The loop's ability to maintain the carrier frequency despite the noise accompanying the PSK signal is measured by the mean and the variance of the oscillator's control voltage. In particular, Spilker's loop for QPSK and the Costas loop for BPSK signals are discussed.