Al2O3陶瓷蠕动进给超声磨削特性试验研究

在改装成的超声磨削机床上进行了陶瓷超声磨削与普通磨削的对比试验,以揭示蠕动进给超声磨削加工的磨削特性及其材料去除机理。结果表明:当超声振动方向与磨削进给方向相同时,超声振动所引起的抛磨作用非常显著,超声磨削的表面粗糙度比机械磨削的低;Al2O3陶瓷在一般条件下超声磨削的去除方式仍属于脆性断裂,以晶粒粉碎、穿晶断裂为主,但伴随有沿晶断裂、弹性划擦、塑性流动等现象。     

磁流变弹性体砂轮抛光镍基高温合金表面完整性研究

为了改善磨削后镍基高温合金GH4169的表面完整性,本文采用磁流变弹性体砂轮对镍基高温合金GH4169进行抛光试验研究。首先,通过模压成型的方法制备了磁流变弹性体砂轮,并对其表面微观形貌及不同磁场强度下的硬度进行了表征。其次将制备出的磁流变弹性体砂轮用于对镍基高温合金GH4169的抛光工艺试验中,并讨论抛光工艺参数中磁场强度对镍基高温合金表面完整性的影响。试验结果表明：在一定的磁场强度范围内,零件抛光后的表面粗糙度和显微硬度随着磁场强度的增大而减小,同时增大磁场强度也有利于改善零件的表面形貌,减少砂轮的磨损量,降低零件磨削后的亚表面损伤层厚度。     

Fretting wear behaviour of machined layer of nickel-based superalloy produced by creep-feed profile grinding

Fretting wear has an adverse impact on the fatigue life of turbine blade roots. The current work is to comparatively investigate the fretting wear behaviour of the nickel-based superalloy surfaces produced by polishing and creep-feed profile grinding, respectively, in terms of surface/subsurface fretting damage, the friction coefficient, wear volume and wear rate. Experimental results show that the granulated tribolayer aggravates the workpiece wear, while the flat compacted tribolayer enhances the wear resistance ability of workpiece, irrespective of whether the workpiece is processed by polishing or grinding. However, the wear behaviors of tribolayers are different. For the polished surface, when the normal load exceeds 100 N, the main defects are crack, rupture, delamination and peeling of workpiece materials; the wear mechanism changes from severe oxidative wear to fatigue wear and abrasive wear when the loads increase from 50 to 180 N. As for the ground surface, the main wear mechanism is abrasive wear. Particularly, the ground surface possesses better wear-resistant ability than the polished surface because the former has the lower values in coefficient friction (0.23), wear volume (0.06 × 10⁶ μm³) and wear rate (0.25 × 10^?16 Pa^?1). Finally, an illustration is given to characterize the evolution of wear debris on such nickel-based superalloy on the ground surface.     

Developing a novel radial ultrasonic vibration-assisted grinding device and evaluating its performance in machining PTMCs

Particle-reinforcing titanium matrix composites(PTMCs) exhibit the sharp raising applications in modern industries owing to its extraordinary physical and mechanical properties. However, the poor grindability and unstable grinding processes due to the existence of TiC particles and TiB short fibres inside PTMCs, leading to the sudden grinding burn and low material removal rate.In this work, a novel radial ultrasonic vibration-assisted grinding(RUVAG) device with a special cross structure was dev...     

超声ELID 复合磨削磨削力模型研究

以ELID 电解原理为基础,结合超声振动辅助磨削过程中单颗磨粒的运动学分析,建立了超声 ELID 复合磨削条件下的磨削力数学解析模型,并对模型进行了分析和仿真。对模型的分析表明:超声振动改 变了磨粒的运动轨迹,使同等条件下的未变形切屑厚度减小,砂轮的在线电解修整使磨粒始终处于锋锐状态, 而且影响砂轮的实际切削深度,进而对磨削力产生影响。磨削力随着超声振动频率、振幅、电解电压、脉冲比、 电解液电阻率的增大而减小;随着切削深度、工件速度的增大而增大。     

C/C复合材料的超声振动铣磨加工技术

介绍了超声振动铣磨加工,并将其与传统加工方式的相关加工因素对比(如表面质量、切削力等),分析出超声振动铣磨加工相较传统加工方式的优势;并通过超声辅助铣磨正交试验对复合材料表面加工质量的影响,论证超声振动铣磨加工多因素之间变化关系,进而得出影响超声辅助磨削的主要加工因素.     

Effect of grain refinement on cutting force of difficult-to-cut metals in ultra-precision machining

The nickel-based superalloy Inconel 718 is treated with Coupled Ultrasonic and Electric Pulse Treatment(CUEPT), and the surface grain is refined from the average size of 9550.0 nm to287.9, 216.3, 150.5, 126.3, 25.8 nm by different effective treatment currents, respectively. The ultraprecision turning experiments are carried out on the processed workpiece after CUEPT. The experimental results show that the average cutting force increases with the decrease of surface grain size.Moreover, a mathema...     

Effect of ultrasonic vibration on finished quality in ultrasonic vibration assisted micromilling of Inconel718

Inconel718 was machined with the traditional micromilling (TMM) and ultrasonic vibration assisted micromilling (UVAMM) with the different technology parameters, whose surface quality and burrs formation were studied. The results show that TMM often forms pits, bumps and gullies in the size effect range. UVAMM effectively improves the surface quality compared with TMM. The surface defects are significantly reduced with the increase of feed per tooth (ƒ_z). When ƒ_z exceeds 4 μm, the effect of ultrasonic vibration on the surface quality is no longer obvious. The minimum burr size on the down milling side and the up milling side are 50.23 μm and 36.57 μm, respectively. The feasibility of vibration cutting in improving surface quality and suppressing burr size was verified. UVAMM effectively suppresses the formation of built-up edge, which can significantly improve the micromilling process. The cutting force is obtained through simulation and experiment. They are agreement in the change trend. The finite element simulation can be used to predict the cutting force. Compared with TMM, feeding force (F_x), radial force (F_y) and axial force (F_z) of UVAMM decrease by 7.6%, 11.5% and 1.3%, respectively.     

大厚度扩散焊NLU成像检测技术

针对钛合金大厚度扩散焊,基于非线性超声(Non-linear ultrasonic,NLU)原理,构建了一种NLU成像方法和检测系统,设计制备了不同的大厚度扩散焊试件,进行了NLU成像检测试验分析。检测结果表明,采用NLU成像检测方法,可实现钛合金大厚度扩散焊的超声可视化检测,最大检测厚度可达70mm。     

镍基高温合金GH4169磨削参数对表面完整性影响

研究了用单晶刚玉砂轮磨削镍基高温合金GH4169时,磨削参数对表面完整性中的表面特征(表面粗糙度、表面形貌、表面显微硬度和表面残余应力)的影响,以期优化磨削参数.砂轮速度依次选择15,20,25m/s,磨削深度分别选择50,100,150μm,工件速度分别选择5,10,15m/min.研究结果表明:表面粗糙度对工件速度的变化最敏感,表面显微硬度对砂轮速度变化最敏感,表面残余应力对砂轮速度变化最敏感;同时表明了磨削参数对磨削表面形貌、显微硬度梯度、微观组织、残余应力梯度的影响,揭示了表面完整性中的变质层形成规律.其塑性变形层在5～10μm,显微硬度变化影响层为80～100μm,残余应力影响层厚度为80～200μm,其为磨削镍基高温合金表面完整性控制研究提供相关的实验数据基础.      

新型刚玉砂轮磨削GH4169镍基高温合金的性能评价研究

镍基高温合金是航空发动机部件的常用材料,其磨削加工存在工具损耗严重、寿命短等难题。针对3种新研制的刚玉砂轮(分别为粒度60#的微晶和单晶混合磨料砂轮、粒度60#的单晶刚玉砂轮,以及粒度70#的单晶刚玉砂轮),开展了GH4169镍基高温合金材料的磨削试验,从磨削力、磨削温度、砂轮磨损以及表面粗糙度等方面对3种砂轮的磨削性能进行了评价。结果表明,3种砂轮磨削GH4169材料在砂轮磨损和表面粗糙度方面未表现出明显差异,而通过对磨削力和磨削温度的综合评价发现粒度60#的单晶刚玉砂轮的磨削性能更优。3种砂轮磨削GH4169材料的磨削比在0.5~3之间。在正常磨削条件下,3种砂轮的磨削表面粗糙度Ra小于0.4μm。同时发现,砂轮磨损(主要包括磨粒的破碎和脱落)是造成磨削表面缺陷形成的重要原因。     

Al2O3陶瓷蠕动进给超声磨削加工表面质量的试验研究

为探索利用简单形状砂轮对陶瓷材料进行数控展成型面超声磨削,通过对Al2O3陶瓷进行蠕动进给超声磨削和机械磨削对比试验研究,探索各加工参数对磨削表面质量的影响规律.结果表明:超声振动方向与蠕动进给方向平行时可降低表面粗糙度值,而超声振动方向与蠕动进给方向垂直时则不利于改善加工表面质量;在超声磨削条件下,为了提高加工表面质量,应采取较小的磨削深度、较低的进给速度和适当高的磨削速度以及复合进给磨削方式.结合试验结果理论分析了蠕动进给超声磨削和蠕动进给机械磨削加工机理,并根据试验结果选择磨削参数进行了陶瓷叶片型面超声磨削的可行性试验.     

Research on Ultrasonic Vibration Grinding of the Hard and Brittle Materials

It is well known that grinding techniques are main methods to machine hard and brittle materials such as engineering ceramics. But the conventional grinding has many shortcomings such as poorer surface finish,quicker wear and tear of grinding tools,lower effi-ciency and so on. Ultrasonic vibration grinding (UVG) which combines ultrasonic machining and grinding emerged as a developing and promising technique in recent years. In this paper,experimental studies on UVG were conducted on several kinds of hard and brittle material by altering processing parameters such as vibration frequency and its amplitude,diamond abrasive grit size,cutting depth,feeding speed and rotary speed of tools. The experimental results show that alteration in any of above mentioned parameters will bring effects on the processed surface finish of these materials. Of them,the diamond abrasive grit size has the greatest. Moreover,conven-tional grinding experiments were also carried out on these materials. By comparison,it was found that the UVG is superior to the con-ventional method in terms of the ground surface quality,the working efficiency and the wear rate of tools.     

Development of a new high-shear and low-pressure grinding wheel and its grinding characteristics for Inconel718 alloy

Nickel-based alloy has been widely used due to its outstanding mechanical properties. However, Nickel-based alloy is a typical difficult-to-machine material, which is a great constrain for its application in the manufacturing field. To improve the surface quality of the ground workpiece, a new high-shear and low-pressure grinding wheel, with high ratio of tangential grinding force to normal grinding force, was fabricated for the grinding of selective laser melting (SLM) manufactured Inconel718 alloy. The principle of high-shear and low-pressure grinding process was introduced in detail, which was quite different from the conventional grinding process. The fabrication process of the new grinding wheel was illustrated. A serial of experiments with different processing parameters were carried out to investigate the grinding performance of the developed grinding wheel via analyzing surface roughness and surface morphology of the ground workpiece. The optimal processing parameters of high-shear and low-pressure grinding were obtained. The surface roughness of ground workpiece was reduced to 0.232 μm from the initial value of 0.490 μm under the optimal grinding conditions. It was found that the initial scratches on the ground workpiece were almost completely removed after the observations with the metalloscopy and the field-emission scanning electron microscopy (FE-SEM). The capability of the newly developed high-shear and low-pressure grinding wheel was validated.     

纳米电刷镀技术在发动机叶片再制造中的应用

某型发动机高压压气机整流叶片,材料为镍基高温合金.服役过程中因叶片榫头两侧与机匣榫槽发生微动磨损,尺寸减小,导致叶片停用.通过采用现代纳米电刷镀方法,对报废叶片进行再制造,使叶片重新满足使用要求.     

超细晶硬质合金加工机理及加工性能

围绕超细晶硬质合金精密磨削加工、在线电解修整磨削加工、电火花加工、超声复合加工、激光复合加工等加工方法,系统综述了超细晶硬质合金的加工机理和加工性能,并展望了超细晶硬质合金高效精密加工未来的研究重点。     

Electrochemical cutting of mortise-tenon joint structure by rotary tube electrode with helically distributed jet-flow holes

In aero-engines, mortise-tenon joint structures are often used to connect the blades to the turbine disk. The disadvantages associated with conventional manufacturing techniques mean that a low-cost, high-efficiency, and high-quality nickel-based mortise–tenon joint structure is an urgent requirement in the field of aviation engineering. Electrochemical cutting is a potential machining method for manufacturing these parts, as there is no tool degradation in the cutting process and high-quality s...     

矩形薄板在不同边界条件下的固有振动分析

研究了在弹性支撑和弹性嵌固边界条件下,弹性矩形薄板固有振动特性的变化规律。利用单项梁函数组合法推导出矩形薄板在2种边界条件下的振型和固有频率的计算公式,应用此公式计算出弹簧系数的变化和薄板固有频率等特征的变化趋势,为分析实际悬臂板类结构振动的特征打下基础。     

薄壁结构焊接接头CTOD试验分析

设计测试薄壁结构平面应力断裂韧性的三点弯曲测试试样,应用于GH4169焊接接头CTOD测试试验。采用光学金相显微镜和扫描电镜观察分析各试样的裂纹扩展形貌和断口形貌。依据BS7448标准的规定分析CTOD测试过程有效性。结果表明,采用设计三点弯曲试样进行的GH4169焊接接头CTOD测试过程是有效的;GH4169母材的断裂韧性较好,裂纹为延性起裂特性;GH4169焊缝和熔合区的断裂韧性较差,裂纹为脆性起裂特性。     

定向结晶及相应单晶材料弹性常数间的关系

使用解析法和有限元数值方法,对定向结晶镍基高温合金以及相应镍基单晶材料工程弹性常数值进行了研究。结果表明二者之间存在相当紧密的联系,其中的3项常数在理想状态下可以认为是对应相等的,并且,在已知其数值的情况下,可以通过解析法和有限元法计算出定向结晶材料的其余常数。根据计算结果,总结出2类材料弹性常数值的规律,提出了相应的建议。