首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到17条相似文献,搜索用时 109 毫秒
1.
反向旋转双转子系统动力学特性的有限元分析   总被引:1,自引:0,他引:1  
近年来,有限元方法在计算转子系统的动力学特性方面得到了很大的发展。利用有限元方法计算了反向旋转双转子系统的动力学特性,分析了反向旋转双转子结构的临界转速特性和主振型特点。研究了中介轴承刚度和转速比对该双转子系统临界转速的影响。通过对结果的分析,得到一系列十分有益的结论,可为反向旋转双转子系统的设计提供一定的参考价值。  相似文献   

2.
蒋云帆  石斌  张通  陈静  柏国伟 《推进技术》2022,43(10):351-362
中介轴承是耦合双转子航空发动机的关键部件,为了探明中介支承结构特征、装配条件和发动机工况对中介轴承刚度特性的影响,建立了中介圆柱滚子轴承刚度特性分析模型。模型综合考虑了中介支承结构形式、轴承内外环相对旋转方向、内外环配合参数、内外环锁紧螺母拧紧力矩、轴承工作温度、发动机转速、径向载荷和弹性流体动力润滑等方面的影响,分析了某型机中介轴承的径向刚度随各参数的变化规律。结果表明,内外环配合参数和发动机工况对中介轴承的刚度影响较大,设计时应考虑刚度变化对转子系统动力学特性的影响;中介轴承刚度对锁紧螺母的拧紧力矩不敏感。另外,中介轴承刚度同中介支承结构形式及内外环的相对旋转方向密切相关,设计时应结合气动性能和结构动力学的要求合理选取,避免对发动机的可靠性造成不利影响。  相似文献   

3.
带套齿联轴器的转子系统动力学特性研究   总被引:2,自引:1,他引:2       下载免费PDF全文
陈曦  廖明夫  李全坤 《推进技术》2015,36(7):1069-1077
针对大涵道比涡扇发动机低压转子中套齿式刚性联轴器结构,建立了套齿联轴器的力学模型和通过套齿联轴器连接的试验转子系统,通过动力学特性计算选择合适的支承刚度,以满足一阶、二阶临界转速的设计要求。理论分析和试验研究了轴向螺母拧紧力矩对套齿连接刚度以及对转子系统的临界转速、振型和不平衡响应等动力学特性的影响规律。结果表明:轴向螺母拧紧力矩会增大套齿联轴器的连接刚度,并且呈现明显的非线性特征。随着轴向螺母拧紧力矩从60N?m增大到120N?m,转子系统的一阶与二阶临界转速增长率分别为1.23%与0.51%;对应的不平衡响应幅值不同程度地增大;而对应的振型基本保持不变。改变不平衡量的轴向与周向位置会导致不平衡响应幅值大小及其变化率有所不同。  相似文献   

4.
弹性环挤压油膜阻尼器-转子系统临界转速特性   总被引:6,自引:0,他引:6       下载免费PDF全文
曹磊  高德平  江和甫 《推进技术》2008,29(2):235-239
弹性环挤压油膜阻尼器ERSFD是一种新型的旋转机械支点阻尼器,其良好的减振调频特性,能够有效地对转子振动进行控制。为了获得ERSFD-转子系统的临界转速特性,考虑了支点的刚度特性对临界转速的影响。首先,利用有限元接触分析技术和有限差分法计算,分别获得了弹性环和油膜的刚度特性,再通过ERSFD-转子系统的不平衡响应计算获得不同刚度特性下的临界转速特性,经转子动力特性试验验证,最终确定了影响临界转速的重要因素,即弹性环凸台处的接触状态。  相似文献   

5.
王存 《推进技术》2021,42(6):1372-1379
为解决对转双转子航空发动机临界转速求解的难题,满足转子动力学设计需求,结合商业有限元软件,给出直接法和完全法两种临界转速求解方法,并结合算例详细论述了方法的理论基础和求解过程,最终以谐响应分析结果加以验证。研究结果表明:基于商业有限元软件特征值分析的完全法不需要任何振型信息,就可对正反进动曲线进行区分,极大简化了对转双转子系统临界转速的求解过程,而由有限元软件生成矩阵后进行处理并计算的直接法不需迭代,可由一次特征值求解得到全部临界转速。某双转子系统临界转速的计算结果表明,直接法、完全法和谐响应分析的结果完全一致。双转子对转时,正进动临界转速曲线随非激励源转子的转速绝对值增加而降低,使临界转速分布规律区别于同转转子,其动力特性需予以细致考虑。  相似文献   

6.
某微型发动机振动特性计算分析   总被引:2,自引:0,他引:2       下载免费PDF全文
研究了具有锥齿轮啮合及机匣系统的某微型发动机的振动特性。采用弯扭耦合传递矩阵法计算临界转速、不平衡响应和初始弯曲响应,计及转动惯量、陀螺力矩、剪切变形、粘性阻尼和轴向力的影响。为了提高机匣振动固有频率的计算精度,还采用轴质量均布的传递矩阵法计算转子-机匣系统的临界转速与不平衡响应。临界转速及不平衡响应计算结果与试验结果吻合较好。  相似文献   

7.
建立某型舰用燃气轮机压气机转子的有限元模型,对转子的动力学特性进行研究。计算了转子的固有频率和振型,求解了转子的临界转速和不平衡响应,并就转子前支承刚度变化对转子临界转速和不平衡响应的影响进行了分析。结果表明:转子为一刚性转子,其振动行为主要受转子一阶模态影响;转子的一阶临界转速为12 825 r/min;转子不平衡响应对第4级附近存在的不平衡量最敏感;转子前支承刚度增大对转子临界转速影响不大,但对转子不平衡响应有一定影响。本文结果可为燃气轮机的可靠运行及转子的进一步优化设计提供依据。  相似文献   

8.
考虑陀螺效应的转子动力学相似准则   总被引:3,自引:2,他引:1  
王永亮  孙立权  崔颖  韩聿 《航空动力学报》2015,30(12):2840-2847
针对考虑陀螺力矩的转子系统缩尺相似模型与原型是否满足动力学相似的问题,采用量纲分析法推导了考虑陀螺力矩的转子-简单支撑系统相似准则,得到了模型与原型各物理量相似比.通过求解不同相似比下Jeffcott转子系统临界转速的解析解,和利用有限元软件ANSYS对某转子系统临界转速和振型相似性进行了数值模拟,验证了所推导的考虑陀螺力矩转子系统相似准则的正确性.研究表明:考虑陀螺力矩、简单支撑和Rayleigh比例阻尼的转子系统,在相似转速下缩尺模型与原型的固有频率具有相似性,并且临界转速相似.   相似文献   

9.
为提供某型对转发动机低压转子临界转速的设计和调整的理论依据,开展了该转子的临界转速随支承刚度和轴向位置变化规律的研究.以该转子为研究对象,采用有限元法建立了转子动力特性的计算模型,基于不同的支承刚度和轴向位置,运用转子动力学分析软件SAMCEF/ROTOR对低压转子的前4阶临界转速进行了系统的计算分析,揭示了低压转子前4阶临界转速随支承刚度和轴向位置的变化规律.结果表明:支承刚度对低压转子的临界转速有显著影响,而支承轴向位置对临界转速的影响较小.  相似文献   

10.
反向旋转双转子稳态响应计算分析与试验   总被引:12,自引:5,他引:7  
航空发动机采用反向旋转的双转子系统, 有助于减小转子整体陀螺力矩对飞机的影响, 降低机匣负荷, 提高飞机机动性能.分析了一种具有中介轴承的反向旋转双转子结构的稳态响应, 其中介轴承外圈与低压转子联接, 内圈与高压转子联接.针对这种结构, 应用传递矩阵法, 结合边界条件, 分析了反向旋转双转子结构稳态不平衡响应的变化规律, 研究了内、外转子盘轴心轨迹和质心的变化特点, 并进行了相应的试验研究, 验证了计算仿真的相关结论.   相似文献   

11.
《中国航空学报》2021,34(12):110-124
In this paper, the nonlinear resonance characteristics of a dual-rotor system are investigated with the consideration of a local defect on the inter-shaft bearing of the system. A simplified model of the dual-rotor system is proposed by considering that there is a local defect on the inner ring of inter-shaft bearing. The local defect is modelled as an inverted isosceles trapezoidal groove, which can make great influence on the inter-shaft bearing force due to the change of radial clearance of the inter-shaft bearing. The motion equations of the dual-rotor system are formulated by using the Lagrange equation. The Runge-Kutta method is employed to solve the motion equation. The amplitude-frequency response curve of the dual-rotor system is obtained, the abnormal resonance characteristics are analyzed. In addition, the influence of defect parameters, rotors and support parameters and inter-shaft bearing parameters on the amplitude-frequency characteristics of the system are discussed. The results show that there are two main resonance peaks and four abnormal resonance peaks on the amplitude-frequency response curve of the dual-rotor with a local defect on the inner ring of the inter-shaft bearing. Through analyzing the vibration response of the abnormal resonance peaks, it is found that the first two abnormal resonances are caused by the combined resonance, which are related to the inner ring fault and the rotational speed of high or low pressure rotors, and the last two resonances are caused by the induced resonance of the inner ring fault. At the same time, when the parameters of defect, rotors and support and inter-shaft bearing change, the resonance of the system also shows the corresponding change law.  相似文献   

12.
高维反向旋转双转子系统的建模方法及动力特性   总被引:2,自引:0,他引:2  
为了弥补有限元方法预测含局部非线性的双转子系统动力特性的不足,借助有限元软件和固定界面模态综合法,建立了高维双转子系统非线性动力学模型,随后利用Newmark算法思想提出了一种隐式时域求解该问题的方法,该方法的求解效率主要取决于非线性力处的自由度个数.在考虑挤压油膜阻尼器非线性力和中介轴承非线性力的基础上,研究了双不平衡激励作用下的反向旋转双转子系统的非线性动力响应特性.研究表明:系统响应中除内、外转子自转频率外,出现了2个自转频率的组合频率;随中介轴承径向游隙的增加,系统转速分岔图中出现了分岔和混沌现象,且临界转速略有下降;系统轴心轨迹呈花瓣状,与试验结果基本吻合.   相似文献   

13.
含滚动轴承的同向和反向旋转双转子系统动力学响应   总被引:12,自引:8,他引:4  
以双转子航空发动机为研究对象,建立了航空发动机双转子-滚动轴承-机匣耦合动力学模型.模型中考虑了低压转子与高压转子的中介轴承耦合作用,滚动轴承模型中考虑了滚动轴承间隙、非线性赫兹接触力以及变柔性VC(varying compliance)振动等因素.利用仿真模型,进行了同向和反向旋转双转子系统的拍振响应分析,结果表明当高低压转子的转速差较小时,双转子系统的拍振响应明显.同时研究了同转和反转双转子系统轴心轨迹响应的差异,研究表明反向旋转双转子系统的轴心轨迹会形成“花瓣”状.最后,利用双转子试验器验证了仿真结果的正确性,进一步验证本文所建模型的正确性.   相似文献   

14.
航空发动机滚动轴承-双转子系统动态特性分析   总被引:10,自引:7,他引:3  
在滚动轴承动力学和转子动力学分析基础上,建立了含滚动轴承动力学与转子动力学耦合以及高、低压转子间耦合的滚动轴承-双转子系统动力学方程,采用精细积分法和预估-校正Adams-Bashforth-Moulton多步法相结合的算法,对航空发动机滚动轴承-双转子系统非线性动力学方程进行求解,并对滚动轴承结构参数与转子动态特性的关系进行了理论分析.分析结果表明:①中介轴承径向游隙较小时转子系统振动量较小且转子运行较平稳,但中介轴承保持架打滑率会有所提高,应合理选取中介轴承的径向游隙值;中介轴承滚子数量对转子运转稳定性有较大影响,减小中介轴承滚子数量可降低保持架打滑率,但转子系统的振动量会增大;②支承轴承内、外沟曲率半径系数及径向游隙较小时转子系统的振动量较小,转子运转较稳定;支承轴承滚动体数量对转子运转稳定性有较大影响,滚动体数量增多有利于转子系统运行的平稳性.   相似文献   

15.
A 5-DOF Model for Aeroengine Spindle Dual-rotor System Analysis   总被引:1,自引:0,他引:1  
This paper develops a five degrees of freedom(5-DOF) model for aeroengine spindle dual-rotor system dynamic analysis.In this system,the dual rotors are supported on two angular contact ball bearings and two deep groove ball bearings,one of the latter-mentioned bearings works as the inter-shaft bearing.Driven by respective motors,the dual rotors have different co-rotating speeds.The proposed model mathematically formulates the nonlinear displacements,elastic deflections and contact forces of bearings with consideration of 5-DOF and coupling of dual rotors.The nonlinear equations of motions of dual rotors with 5-DOF are solved using Runge-Kutta-Fehlberg algorithm.In order to investigate the effect of the introduced 5-DOF and nonlinear dy-namic bearing model,we compare the proposed model with two models:the 3-DOF model of this system only considering three translational degrees of freedom(Gupta,1993,rotational freedom is neglected);the 5-DOF model where the deep groove ball bearings are simplified as linear elastic spring(Guskov,2007).The simulation results verify Gupta’s prediction(1993) and show that the rotational freedom of rotors and nonlinear dynamic model of bearings have great effect on the system dynamic simula-tion.The quantitative results are given as well.  相似文献   

16.
高速圆柱滚子轴承保持架动力学特性分析   总被引:7,自引:6,他引:1  
建立了高速圆柱滚子轴承动力学微分方程,采用精细积分法和预估-校正Adams-Bashforth-Moulton多步法相结合的算法,对高速圆柱滚子轴承动力学微分方程进行求解,并对保持架的动力学特性进行了理论分析.结果表明:过大的保持架间隙比不利于保持架稳定运转;在一个套圈固定、另一个套圈工作状态下,保持架引导方式采用旋转套圈引导时,保持架打滑率较低;保持架采用外引导方式时保持架质心运动较为稳定;在内外圈同向旋转且外圈转速高于内圈转速条件下,保持架采用外引导方式时,保持架打滑率较低;在内外圈反向旋转且外圈转速高于内圈转速条件下,保持架质心轨迹变得不规则;保持架采用外引导方式时,保持架打滑率为负值.   相似文献   

17.
《中国航空学报》2021,34(10):128-147
Rolling bearing and Squeeze Film Damper (SFD) are used in rotor support structures, and most researches on the nonlinear rotor-bearing system are focused on the simple rotor-bearing systems. This work emphasizes the comparative analysis of the influence of SFD on the nonlinear dynamic behavior of the dual-rotor system supported by rolling bearings. Firstly, a reduced dynamic model is established by combining the Finite Element (FE) method and the free-interface method of component mode synthesis. The proposed model is verified by comparing the natural characteristics obtained from an FE model with those from the experiment. Then, the steady-state vibration responses of the system with or without SFD are solved by the numerical integration method. The influences of the ball bearing clearance, unbalance, centralizing spring stiffness and oil film clearance of SFD on the nonlinear steady-state vibration responses of the dual-rotor system are analyzed. Results show that SFD can effectively suppress the amplitude jump of the dual rotor system sustaining two rotors unbalance excitations. As the ball bearing clearance or unbalance increases, the amplitude jump phenomenon becomes more obvious, the resonance hysteresis phenomenon strengthens or weakens, the resonant peaks shift to the left or the right, respectively. SFD with unreasonable parameters will aggravate the system vibration, the smaller the oil film clearance, the better the damping performance of the SFD, the larger the centralizing spring stiffness is, the larger resonance amplitudes are.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号