共查询到20条相似文献,搜索用时 201 毫秒
1.
2.
本文对微细切削刀具在微细切削加工中的作用进行了阐述.根据微细切削刀具的工作环境,分析了其应当具备的特点;从微细切削刀具的加工机理、设计方法和制备技术三个方面概述了与微细切削刀具相关的研究成果;针对该研究方向上目前存在的瓶颈问题进行了总结. 相似文献
3.
本文对微细切削刀具在微细切削加工中的作用进行了阐述。根据微细切削刀具的工作环境,分析了其应当具备的特点;从微细切削刀具的加工机理、设计方法和制备技术三个方面概述了与微细切削刀具相关的研究成果;针对该研究方向上目前存在的瓶颈问题进行了总结。 相似文献
4.
5.
作者研制的超声旋转三维数控加工机 ,具有电流反馈式频率跟踪及进给压力自适应控制功能 ,用它进行了碳纤维复合材料超声旋转孔加工实验研究。对于直径不大于Φ 1 0 mm的孔 ,采用硬质合金钻头加工。对于直径大于 Φ1 0 mm的孔 ,采用电镀金刚石工具套料加工。并尝试用小工具加工大孔的超声轮廓控制加工方法。上述实验研究均取得了较好的效果。 相似文献
6.
廖文敏 《北华航天工业学院学报》2011,21(6):18-20
针对硬质合金模具的加工表面精度要求,进行了高速钢与硬质合金两种材料的电火花加工工艺对照实验。为获得较低的表面粗糙度,选取了较小的电加工参数。实验结果表明,在该实验条件下,电火花加工的表面粗糙度不再满足常规条件下的经验公式,而与工件材料的再凝结特征、成分及电蚀产物的排出条件有关。 相似文献
7.
廖文敏 《华北航天工业学院学报》2011,(6):18-20
针对硬质合金模具的加工表面精度要求,进行了高速钢与硬质合金两种材料的电火花加工工艺对照实验。为获得较低的表面粗糙度,选取了较小的电加工参数。实验结果表明,在该实验条件下,电火花加工的表面粗糙度不再满足常规条件下的经验公式,而与工件材料的再凝结特征、成分及电蚀产物的排出条件有关。 相似文献
8.
发动机涡轮导向叶片气膜孔的加工工艺 总被引:1,自引:0,他引:1
《航天制造技术》2008,(6)
介绍了高速电火花小孔加工的工作原理和加工工艺,通过实际工件的加工试验,得出了叶片型面上小孔加工的工艺参数,采用此工艺方法加工的气膜孔能够满足其表面质量、位置精度和其它设计要求。 相似文献
9.
球头零件和凸、凹球面表面是航天型号产品中较难加工的零件和表面。文中介绍了在普通电火花线切割机床上用薄壁筒状电极电火花磨削加工球头及球面的方法、原理;加工方案、机床的改装;加工要点及如何选择加工参数。 相似文献
10.
新工艺新功能材料与微电子技术是传感器发展的三大基础技术。本领域的主要关键技术是有限元分析计算软件与CAD设计系统,异型构件的坯件制造、精密微细加工技术,新的联结与封装技术等几个方面,简介了若干实例。 相似文献
11.
介绍了一种新的刚体转动的四元数模型。这些模型可以提高再定向控制的对边界条件的适应能力,在此基础上还介绍了这些模型的一些实际应用。 相似文献
12.
A. A. Davydov 《Cosmic Research》2011,49(4):335-344
A communication satellite (small spacecraft) injected into a geosynchronous orbit is considered. Flywheel engines are used
to control the rotational spacecraft motion. The spacecraft after the emergency situation has passed into a state of uncontrolled
rotation. In this case, no direct telemetric information about parameters of its rotational motion was accessible. As a result,
the problem arose to determine the rotational satellite motion according to the available indirect information: current taken
from the solar panels. Telemetric measurements of solar panel current obtained on the time interval of a few hours were simultaneously
processed by the least squares method integrating the equations of rotational satellite motion. We present the results of
processing 10 intervals of the measurement data allowing one to determine the real rotational spacecraft motion and to estimate
the total angular momentum of flywheel engines. 相似文献
13.
14.
为满足航天器微振动环境模拟的需要,开展了多自由度微振动时域波形复现控制方法研究。首先,介绍了基于时域波形复现的多自由度微振动环境模拟控制理论方法。其次,针对六自由度微振动激励系统,应用MATLAB软件建立了基于实测传递函数矩阵的多输入多输出微振动激励仿真系统,针对微振动时域波形复现闭环控制过程进行了算法编程,并给出了仿真的闭环控制流程图。最后,通过算例对多自由度微振动时域波形复现进行了数值仿真,以给定的白噪声为输入,模拟对实际存在的系统非线性、测量误差等影响因素的控制效果。仿真结果验证了多自由度微振动时域波形复现控制方法的可行性及有效性,所得结论可以为研究多自由度微振动时域波形复现控制系统提供参考。 相似文献
15.
The problem of determining an estimation of current spacecraft motion parameters on the stage of its descent is solved on the basis of readings of an optoelectronic navigation system and additional information from the self-contained inertial navigation system at the most general assumptions on the nature of motion of the object and the statistical properties of the noise of the measuring devices. 相似文献
16.
17.
The problem of optimal control over many-revolution spacecraft orbit transfers between circular coplanar orbits of satellites is considered. The spacecraft flight is controlled by a thrust vector of a jet engine with restricted thrust (JERT). The mass expenditure is minimized at a limited time of flight. The optimal control problem is solved based on the maximum principle. The boundary value problem of the maximum principle is solved numerically using the shooting method. A modified computation scheme of the shooting method is suggested (multi-point shooting), as well as a method (correlated with the scheme) of choosing the initial approximation with the use of a solution to the optimization problem in the impulse formulation. The scheme and method allow one to construct many-revolution spacecraft orbit transfers. 相似文献
18.
热变形对天线指向机构的指向精度具有重要影响,但利用传统的设计方法很难实现对指向精度的准确计算,尤其是热变形对指向精度影响的研究工作更是少见。为此建立了机构的三维实体热-结构耦合有限元分析模型,根据有限元分析结果并结合机构的运动链关系,构建了各关键运动副运动误差的计算方法;在此基础上实现了机构指向误差的计算,研究了运动副名义、最大以及最小配合间隙条件下,温度载荷对各关键运动副运动误差和指向精度的影响。研究结果表明,温度载荷对关键运动副的运动误差以及机构的指向精度具有重要影响,随着温度载荷偏离常温数值的增加,指向误差不断增大,名义配合间隙条件下的指向误差最大。 相似文献
19.