图像目标跟踪及其在UCAV中的应用

在图像跟踪中主要因素是目标的几何中心，只考虑目标的相对运动特性，就可以设法减少图像处理的工作量。由于目标的边缘不可能占满整幅图像．在目标边缘检测时不必对整幅图像进行处理。为此，从估计的中心向给定方向寻找目标的边界．得到目标边界点的一个子集合．再由该子集得到目标中心的近似值．并以此为基础构造目标跟踪方法，利用图像检测实现无人战斗机对目标的跟踪。仿真结果表明．该方法对于目标的跟踪是有效的。     

Low observable target motion analysis using amplitude information

In conventional passive and active sonar system, target amplitude information (AI) at the output of the signal processor is used only to declare detections and provide measurements. We show that the AI can be used in passive sonar system, with or without frequency measurements, in the estimation process itself to enhance the performance in the presence of clutter where the target-originated measurements cannot be identified with certainty, i.e., for “low observable” or “dim” (low signal-to-noise ratio (SNR)) targets. A probabilistic data association (PDA) based maximum likelihood (ML) estimator for target motion analysis (TMA) that uses amplitude information is derived. A track formation algorithm and the Cramer-Rao lower bound (CRLB) in the presence of false measurements, which is met by the estimator even under low SNR conditions, are also given. The CRLB is met by the proposed estimator even at 6 dB in a cell (which corresponds to 0 dB for 1 Hz bandwidth in the case of a 0.25 Hz frequency cell) whereas the estimator without AI works only down to 9 dB. Results demonstrate improved accuracy and superior global convergence when compared with the estimator without AI. The same methodology can be used for bistatic radar     

一种新的非平行轨迹机载双站斜视SAR成像算法(英文)

本文提出了一种用于非平行轨迹机载双站斜视SAR条带模式成像的新的解析算法。该算法用收、发雷达的多普勒调频率贡献比为加权系数推导了点目标回波的二维频谱。通过解目标位置相对于收、发载机飞行轨迹的耦合,将这个二维频谱中目标的距离参数和方位参数进行了分离。在二维频域内,补偿掉双站扭曲项后利用二维Chirp-Z变换(2D-CZT)校正了距离向和方位向的徙动,获得了精确聚焦的目标图像。雷达回波的二维残余徙动用沿距离向和方位向的分块来限制,推导了数据分块的条件,由此可以实现宽场景成像。仿真试验验证了这种2D-CZT算法的有效性。     

Novel Approach for ISAR Image Cross-Range Scaling

Inverse synthetic aperture radar (ISAR) imaging systems produce electromagnetic images of targets in the range-Doppler domain. In order to rescale the image in a homogeneous range-cross range domain (meters by meters), the modulus of the target effective rotation vector must be known. Although in some cases it can be retrieved by means of ancillary data, in most cases the modulus of the target effective rotation vector must be estimated. A blind technique is proposed for estimating the modulus of the target effective rotation vector that exploits information carried by the chirp rate of scattering centres. A technique based on image segmentation, local polynomial Fourier transform (LPFT), and image contrast (IC) maximisation is used in order to extract the scattering centres and estimate their chirp rate. Simulated and real data analyses are provided to confirm the effectiveness of the proposed algorithm.     

机动目标的逆合成孔径雷达成像

 逆合成孔径雷达(ISAR)和合成孔径雷达 (SAR)都是利用目标 (场景)与雷达的相对运动,提高横向分辨率,实现对目标 (场景 )的成像。SAR的运动方是雷达平台,可控制作平稳飞行,且用仪器测校其偏离误差;ISAR的运动方通常是非合作目标,运动不受控制,且难以精确测量。当目标作机动飞行时,以目标作固定基准,雷达等效地在空间形成流形复杂的逆合成孔径 (阵列 ),对这种情况下成像的问题进行了系统的研究。     

Efficient Approximation of Kalman Filter for Target Tracking

A Kalman filter in the Cartesian coordinates is described for a maneuvering target when the radar sensor measures range, bearing, and elevation angles in the polar coordinates at high data rates. An approximate gain computation algorithm is developed to determine the filter gains for on-line microprocessor implementation. In this approach, gains are computed for three uncoupled filters and multiplied by a Jacobian transformation determined from the measured target position and orientation. The algorithm is compared with the extended Kalman filter for a typical target trajectory in a naval gun fire control system. The filter gains and the tracking errors for the proposed algorithm are nearly identical to the extended Kalman filter, while the computation requirements are reduced by a factor of four.     

Data fusion and tracking using HMMs in a distributed sensor network

This work deals with the problem of multiple target tracking, from the measurements made on a field of passive sonars activated by an active sonar (multistatic network). The difficulties encountered then are of two kinds: each sensor alone does not provide full observability of a target, and multiple, possibly maneuvering targets moving in a cluttered environment must be dealt with. The algorithm presented here is based on a discrete Markovian modelization of the targets evolution in time. It starts with a fusion of the detections obtained at each measurement time. Tracking and target motion analysis (TMA) are next achieved thanks to dynamic programming (DP). This approach leads to multiple and maneuvering target tracking, with few assumptions; for instance, the use of deterministic target state models are avoided. Simulation results are presented and discussed.     

Track-While-Scan Algorithm in a Clutter Environment

A track-while scan (TWS) algorithm is developed for targets in a clutter environment. The problem has been studied using only the position measurements [1, 5-8], but the simulation results have not been satisfactory. Modern processing techniques (FFT processor) ) in air traffic control and surveillance radar receivers provide both position and radial velocity. The radial velocity measurement may be conveniently used in the target-track correlation process, which will reduce the association ambiguity in the clutter environment. t. In the clear environment the algorithm using the position and radial velocity measurements has been treated in [3, 4]. A TWS algorithm, using both position and radial velocity measurements for targets in a clutter environment, is presented here. The algorithm obtained is nonlinear and adaptive. In order to evaluate the improvement due to radial velocity measurement a simulation has been performed on a digital computer. The algorithm was run with and without radial velocity measurements to compare its performances. An improvement was noted especially when the target path included an accelerated portion.     

一种基于移动辅助节点的单兵导航系统协同初始化算法

惯性导航系统凭借其自主性强、隐蔽性好、可靠性高的优势,在单兵作战、反恐救援中发挥越来越重要的作用。针对单兵惯性导航系统精度较低,在长期工作后精度下降严重,需要重新初始化的问题,以单兵与无人平台的协同作业为背景,提出了一种基于移动式辅助节点的单兵导航系统协同快速初始化方法。该方法以目标节点的角增量、位移增量信息与测距信息作为输入,采用粒子滤波技术对单兵导航系统的位置和航向进行协同估计。试验表明,该算法最少仅需1个辅助节点即可实现较好的单兵惯导系统位置和航向初始化。     

Velocity Estimation from Position Outputs of a Three-Dimensional Radar

Kalman filtering equations to obtain estimates of velocity from radar position information are defined. In a track-while-scan operation, a three-dimensional radar sensor measures range, bearing, and elevation (r, ?, ?) of an airborne target at uniform sampling intervals of time T. The noisy position measurements are converted to x, y, z coordinates and put through a Kalman filter to obtain x, y, z velocity components. The filtering equations together with steady-state error estimates are given.     

Multi-Target/Multi-Sensor Tracking using Only Range and Doppler Measurements

A new approach is described for combining range and Doppler data from multiple radar platforms to perform multi-target detection and tracking. In particular, azimuthal measurements are assumed to be either coarse or unavailable, so that multiple sensors are required to triangulate target tracks using range and Doppler measurements only. Increasing the number of sensors can cause data association by conventional means to become impractical due to combinatorial complexity, i.e., an exponential increase in the number of mappings between signatures and target models. When the azimuthal resolution is coarse, this problem will be exacerbated by the resulting overlap between signatures from multiple targets and clutter. In the new approach, the data association is performed probabilistically, using a variation of expectation-maximization (EM). Combinatorial complexity is avoided by performing an efficient optimization in the space of all target tracks and mappings between tracks and data. The full, multi-sensor, version of the algorithm is tested on simulated data. The results demonstrate that accurate tracks can be estimated by exploiting spatial diversity in the sensor locations. Also, as a proof-of-concept, a simplified, single-sensor range-only version of the algorithm is tested on experimental radar data acquired with a stretch radar receiver. These results are promising, and demonstrate robustness in the presence of nonhomogeneous clutter.     

基于最大似然估计的TDOA/FDOA无源定位偏差补偿算法

在到达时差/到达频差(TDOA/FDOA)无源定位系统中,定位问题的非线性使得定位的结果存在偏差,特别是在噪声较大或者接收站布站不合理的情况下,定位的偏差尤其显著。针对这一问题,提出了一种基于最大似然估计的偏差补偿算法。该方法分为3步:首先,利用最大似然估计器对目标的位置和速度进行求解;其次,通过利用目标定位的估计值和含噪的测量值,对目标的位置和速度偏差值进行理论分析和推导;最后,将最大似然估计解减去理论偏差值,得到经过偏差补偿的新的目标定位解。理论分析和实验仿真证明,在一定噪声的情况下,所推导的目标位置和速度的理论偏差值与实际偏差值相符,并且经过偏差补偿后的定位算法,在保持目标定位的均方根误差(RMSE)与原最大似然算法一致的情况下,目标的位置和速度偏差值远远小于原最大似然算法的偏差值,目标定位精度得到了有效的提高。     

光电经纬仪红外成像跟踪处理器的研究与实现

以高性能数字信号处理器TMS320C6203为核心,结合CPLD（可编程逻辑器件）进行逻辑控制,用FPGA（现场可编程门阵列）进行预处理,设计了实时目标检测和跟踪系统。介绍了实时图像处理系统的硬件组成、工作原理、软件流程,重点分析目标检测算法和系统实时性。该系统被成功用于光电经纬仪红外图像处理系统中,经试验证明,系统对弱小目标的检测、识别和跟踪能力达到实际工程的实时性需求,大大提高了数据采集能力与处理速度,采样精度得到很大提高,完全满足系统设计要求。     

GPS code and carrier multipath mitigation using a multiantennasystem

Multipath is a major source of error in high precision Global Positioning System (GPS) static and kinematic differential positioning. Multipath accounts for most of the total error budget in carrier phase measurements in a spacecraft attitude determination system. It is a major concern in reference stations, such as in Local Area Augmentation Systems (LAAS), whereby corrections generated by a reference station, which are based on multipath corrupted measurements, can significantly influence the position accuracy of differential users. Code range, carrier phase, and signal-to-noise (SNR) measurements are all affected by multipath, and the effect is spatially correlated within a small area. In order to estimate and remove code and carrier phase multipath, a system comprising a cluster of five GPS receivers and antennas is used at a reference station location. The spatial correlation of the receiver data, and the known geometry among the antennas, are exploited to estimate multipath for each satellite in each antenna in the system. Generic receiver code and carrier tracking loop discriminator functions are analyzed, and relationships between receiver data, such as code range, carrier phase, and SNR measurements, are formulated and related to various multipath parameters. A Kalman filter is described which uses a combination of the available information from the antennas (receivers) in the multiantenna cluster to estimate various multipath parameters. From the multipath parameters, the code range and carrier phase multipath is estimated and compensated. The technique is first tested on simulated data in a controlled multipath environment. Results are then presented using field data and show a significant reduction in multipath error     

Monocular Vision-based Two-stage Iterative Algorithm for Relative Position and Attitude Estimation of Docking Spacecraft

Visual sensors are used to measure the relative state of the chaser spacecraft to the target spacecraft during close range rendezvous phases. This article proposes a two-stage iterative algorithm based on an inverse projection ray approach to address the relative position and attitude estimation by using feature points and monocular vision. It consists of two stages: absolute orientation and depth recovery. In the first stage, Umeyama's algorithm is used to fit the three-dimensional (3D) model set and estimate the 3D point set while in the second stage, the depths of the observed feature points are estimated. This procedure is repeated until the result converges. Moreover, the effectiveness and convergence of the proposed algorithm are verified through theoretical analysis and mathematical simulation.     

SAR image formation via semiparametric spectral estimation

A new algorithm, referred to as the SPAR (Semiparametric) algorithm, is presented herein for target feature extraction and complex image formation via synthetic aperture radar (SAR). The algorithm is based on a flexible data model that models each target scatterer as a two-dimensional (2-D) complex sinusoid with arbitrary unknown amplitude and constant phase in cross-range and with constant amplitude and phase in range. By attempting to deal with one corner reflector, such as one dihedral or trihedral, at a time, the algorithm can be used to effectively mitigate the artifacts in the SAR images due to the flexible data model. Another advantage of SPAR is that it can be used to obtain initial conditions needed by other parametric target feature extraction methods to reduce the total amount of computations needed. Both numerical and experimental examples are provided to demonstrate the performance of the proposed algorithm     

Data association for deghosting in Y-shaped passive linear array sonars

This paper deals with data association using three sets of passive linear array sonars (PLAS) geometrically positioned in a Y-shaped configuration, fixed in an underwater environment. The data association problem is directly transformed into a 3D assignment, which is known to be NP hard. For generic passive sensors, it can be solved using conventional algorithms, while in PLAS, it becomes a formidable task due to the presence of bearing ambiguity. Thus, the central issue of the problem in PLAS is how to eliminate the bearing ambiguity without increasing tracking error. To solve this problem, the 3D assignment algorithm used the likelihood value of only those observed bearing measurements is modified by incorporating frequency information in consecutive time-aligned scans. The region of possible ghost targets is first established by the geometrical relation of PLAS with respect to target. The ghost targets are then confirmed and eliminated by generating multiple observations in consecutive scans. Representative simulations demonstrate the effectiveness of the proposed approach.     

基于序列图像的航天器自主导航降维滤波方法

非合作目标的运动感知与状态估计,是太空领域技术发展的重要组成部分。非合作目标相对状态的精确估计是相对导航的难点问题。传统的非合作目标扩展卡尔曼滤波算法需要结合非合作目标的质心位置,增加了状态变量的维数,提高了系统不确定性,从而会影响状态扩展卡尔曼滤波的收敛速度。提出了一种基于序列图像的非合作目标相对导航方法,该方法在不对质心进行估计的情况下首先对非合作目标姿态进行估计,在完成非合作目标姿态估计后再对其质心进行估计。本文推导了光学相机测量值与目标真实姿态的关系,构建了基于序列图像的测量模型,分别建立了不含有非合作目标质心位置的状态方程和基于非合作目标位置、速度矢量的状态方程,设计了适用于非合作目标状态估计的扩展卡尔曼滤波算法。仿真实验表明该方法可在10 Hz采样频率下经过50次采样（即5 s）内快速收敛,从而有利于空间飞行器的在轨服务与维护。     

Track formation with bearing and frequency measurements in clutter

Target motion analysis from a narrowband passive sonar that yields bearing and frequency measurements in the presence of false detections (clutter) in a low-SNR (low signal-to-noise ratio) environment is discussed. The likelihood function used to compute the maximum likelihood estimation of the track parameters (localization and frequency) incorporates the false alarms via the probabilistic data association technique. The Cramer-Rao lower bound is calculated and results obtained from simulations are shown to be compatible with it. A test of track acceptance is also presented     

双基地角时变下的ISAR等效旋转中心估计

双基地逆合成孔径雷达（ISAR）距离-多普勒算法成像时，容易引起越分辨单元徙动问题，影响成像质量，为了抑制越分辨单元徙动，需要估计目标的等效旋转中心。本文针对双基地角时变下的ISAR等效旋转中心估计问题，提出了一种等效旋转中心估计算法。该算法首先将运动补偿后的一维距离像序列分为两组并分别成像，得到两幅图像；其次，假定某个距离单元为等效旋转中心位置，对两幅图像进行畸变校正，使得两幅图像只存在一个视角差，按视角差旋转其中的一幅图像，并与另一幅图像作相关，得到相关系数；然后，假定下一个距离单元为等效旋转中心位置，重复上述步骤，直至遍历结束，相关系数最大值对应的假定位置就是估计的等效旋转中心。最后进行了仿真对比实验，表明本文算法能够有效估计双基地角时变下的ISAR等效旋转中心位置。