基于地面移动通信基站的差分气压测高方法

为了解决现有的卫星定位系统高程定位精度较低的问题,提出利用已发展完备的地面移动通信基站作为气压差分测量基准点的差分气压测高的方法.该方法以用户接收机附近的分布密集的地面移动通信基站为气压校正基准点,并利用移动通信基站的传输链路把相关的测量数据传送给用户,用户接收机便可以用移动通信基站观测点的高程值、气压值以及温度值,结合接收机测点处的气压值和温度值,利用高程与气压值之间的对应关系,得到用户接收机处的绝对高程值.实际试验结果表明:使用本方法后,室内高程定位精度约为1 m,室外的高程定位精度优于1 m.测高分辨率约为0.2 m,可以使GNSS(Global Navigation Satellite System)的三维位置定位精度提高约60%.本方法不仅可以弥补GNSS高程精度差的缺陷,作为高程约束参与测量方程解算还会提高水平测量精度,而且还克服了传统的气压测高精度依赖于气象站,而大多数用户接收机离气象站的距离较远,造成气压测高精度偏低的局限性.所以本方法能辅助增强卫星导航系统,提高三维定位精度,用于室内定位可以解决室内楼层的分辨问题.     

基于帝国竞争优化的双目标综合决策选星算法

全球卫星导航系统（GNSS）的应用前景已经得到世界各国的普遍承认,其应用领域也趋于多样化,在此背景下,卫星接收机也要求其具有更快的解算速度和可靠的精度。针对目前多数接收机的选星算法都是固定选星数目从而限制算法机动性的问题,提出基于帝国竞争优化算法（ICA）的双目标综合决策选星算法。为了更好获取几何构型较好的卫星星座,引入可见卫星的卫星仰角和方向角先验信息,进行先验性约束,通过构建几何精度因子（GDOP）以及选星数目2个目标,进行综合决策的快速选星,提高了选星的灵活度,并且在满足用户精度的要求下减轻了多星座卫星接收机的计算负担。通过仿真实验和实测数据对双目标综合决策选星算法验证的结果表明:所提算法在高度截止角5°下引入先验性约束条件后平均选星数目在仿真数据和实测数据中缩减率分别为51.8%和45.4%,平均GDOP值较无约束下分别减少0.209 2和0.248 4。同时,所提算法单次选星平均耗时分别为0.168 4 s和0.303 1 s,与遍历法的选星耗时4 s相比,提高了95.79%和92.42%。      

基于混沌粒子群优化的北斗/GPS组合导航选星算法

全球卫星导航系统（GNSS）接收机在接收信号的过程中会受到诸如建筑物遮挡、信号干扰等因素的影响,无法得到全部可见星。为减轻多星座组合接收机的处理负担,研究利用部分可见卫星进行定位的快速选星算法,提出了一种基于混沌粒子群优化（CPSO）的北斗/GPS组合导航选星算法。首先,对当前历元时刻可见卫星进行连续编码,按照选星数目分组,每个分组视为一个粒子。然后,通过混沌映射初始化粒子种群,选取几何精度因子（GDOP）作为评价粒子优劣的适应度函数;粒子通过粒子群优化算法的速度-位移模型更新自身位置,逐渐趋近空间卫星几何分布较好的卫星组合全局最优解。最后,采集北斗/GPS实际数据对选星算法进行仿真验证和性能比较,结果表明,所提算法在选星颗数多于5颗时,单次选星耗时为遍历法选星的37.5%,选星结果的几何精度因子计算误差在0~0.6之间。该算法可适用于北斗/GPS组合导航定位不同选星颗数的情况。      

Enhanced multipath mitigation method based on multi-resolution CNR model and adaptive statistical test strategy for real-time kinematic PPP

This study proposes an enhanced multipath mitigation method based on multi-resolution carrier-to-noise-ratio (CNR) model and adaptive statistical test strategy for real-time kinematic precise point positioning (PPP) applications. The multi-resolution CNR model is established with GPS observation data collected from DOY 152 to 181 of 2019 by 230 globally distributed IGS stations, which used to analyze the relevant factors affecting CNR. Statistical results indicate that the CNR is not only related to the satellite elevation, but also closely related to the receiver types and specific satellite. The maximum difference between different receivers can reach 20 dB for the same satellite at the same elevation. In addition, the performance of the CNR is also obviously different between each satellite, and the maximum difference between different satellites is about 10 dB for the same receiver at the same elevation. Hence, in terms of the method which is based on CNR information for multipath detection and mitigation, the independence of receiver types, satellite and frequency must be considered. With the above analysis, this study developed a multi-resolution CNR model based on different receiver types, different satellites and different elevation firstly. Then, combined with the adaptive statistical test strategy which is based on the difference of CNR between inter-frequency and the difference of CNR between adjacent epochs, the multipath can be detected effectively. For the epoch which affected by multipath, the down-weighted strategy based on CNR is adopted to mitigate the influence of multipath on positioning. Real-time kinematic PPP data are collected to assess the proposed method, and the results demonstrate that the proposed method can detect the multipath effectively, and the detection rate can reach 90.28%. Moreover, after adopting the mitigation strategy, the RMS bias of the east, north and up components are improved about 19.95%, 17.89% and 23.07% compared to the original results, respectively. It is worth noting that this proposed method is also suitable for other GNSS, such as GLONASS and BDS, but the corresponding CNR model must be established simultaneously.     

基于信道复用方法的GNSS共视信号模拟

全球导航卫星系统（GNSS）共视（CV）技术应用中需要对GNSS共视信号进行模拟仿真,可以降低对共视接收机和共视算法进行测试过程中的成本。为此,提出了一种基于信道复用方法的GNSS共视信号的双路信号模拟方法。首先,对GNSS共视技术原理进行了分析。然后,根据GNSS直射信号的模拟思路,设计了基于GNSS直射信号模拟器的GNSS共视信号模拟方法,对共视信号传播过程中可能产生的误差进行了分析。最后,对零基线、短基线、长基线3种场景下仿真的共视信号,以及实场采集的试验数据进行了验证分析。验证的结果表明,仿真的GNSS共视信号定位准确,定位精度在米级;共视比对结果均方根值（RMS）精度优于12 ns,可以进行共视法时间传递,证明了提出的共视信号模拟方法能够有效地用于GNSS共视信号生成。对GNSS共视信号模拟器、共视接收机的研制和共视算法的研究具有一定的理论参考意义和实际应用价值。      

Demonstration of a high sensitivity GNSS software receiver for indoor positioning

Advances in signal processing techniques contributed to the significant improvements of GNSS receiver performance in dense multipath environments and created the opportunities for a new category of high-sensitivity GNSS (HS-GNSS) receivers that can provide GNSS location services in indoor environments. The difficulties in improving the availability, reliability, and accuracy of these indoor capable GNSS receivers exceed those of the receivers designed for the most hostile urban canyon environments. The authors of this paper identified the vector tracking schemes, signal propagation statistics, and parallel processing techniques that are critical to a robust HS-GNSS receiver for indoor environments and successfully incorporated them into a fully functional high-sensitivity software receiver. A flexible vector-based receiver architecture is introduced to combine these key indoor signal processing technologies into GSNRx-hs™ – the high sensitivity software navigation receiver developed at the University of Calgary. The resulting receiver can perform multi-mode vector tracking in indoor environment at various levels of location and timing uncertainties. In addition to the obvious improvements in time-to-first-fix (TTFF) and signal sensitivity, the field test results in indoor environments surrounded by wood, glass, and concrete showed that the new techniques effectively improved the performance of indoor GNSS positioning. With fine GNSS timing, the proposed receiver can consistently deliver indoor navigation solution with the horizontal accuracy of 2–15 m depending on the satellite geometry and the indoor environments. If only the coarse GNSS timing is available, the horizontal accuracy of the indoor navigation solution from the proposed receiver is around 30 m depending on the coarse timing accuracy, the satellite geometry, and the indoor environments. From the preliminary field test results, it has been observed that the signal processing sensitivity is the dominant factor on the availability of the indoor navigation solution, while the GNSS timing accuracy is the dominant factor on the accuracy of the indoor navigation solution.     

粒子群优化粒子滤波的接收机自主完好性监测

接收机自主完好性监测（RAIM）是航空卫星导航接收机必不可少的功能,为保持全球卫星导航系统（GNSS）在卫星发生故障时系统性能不降级,需要对卫星故障进行检测和隔离。针对接收机观测噪声非高斯分布的特点,提出一种基于粒子群优化粒子滤波（PSO-PF）的故障检测和隔离算法。通过粒子群优化粒子滤波对状态估计进行一致性检验实现故障检测。采集实测数据验证算法的检测性能,并与基于基本粒子滤波的完好性监测算法进行比较,结果表明:本文所提算法在非高斯测量噪声下可检测并隔离全球定位系统（GPS）故障卫星,其性能优于基于基本粒子滤波的完好性监测算法性能,对研究北斗卫星导航系统（BDS）接收机自主完好性监测具有一定的意义。      

Carrier phase prediction method for GNSS precise positioning in challenging environment

Since the signals of global navigation satellite system (GNSS) are blocked frequently in challenging environments, the discontinuous carrier phases seriously affect the application of GNSS precise positioning. To improve the carrier phase continuity, this paper proposes a carrier phase prediction method based on carrier open-loop tracking. In the open-loop tracking mode, the carrier numerically controlled oscillator (NCO) is controlled by the predicted Doppler, but not by the loop filter output. To improve the phase prediction effective time, accurate receiver clock drift estimation is studied in the prediction method. The phase prediction performance is tested on GNSS software receiver. In the phase prediction effective time tests, open-loop processes were set for the tested channel. The test results show that, when some satellite signals are blocked in 15?s, the probability of carrier phase error less than quarter cycles is more than 94%. In the real time kinematic (RTK) positioning tests, some satellite signals are blocked in 10–15?s repeatedly. The test results show that, the carrier phase continuity is basically not affected by the signal interruption, and the RTK can almost keep continuous centimeter-level positioning accuracy without re-fixing the integer ambiguity.     

Evaluation and analysis on positioning performance of BDS/QZSS satellite navigation systems in Asian-Pacific region

By using the observation data and products of precise obit and clock offset from Multi-GNSS Experiment (MGEX) of the International GNSS Service (IGS) and GNSS Research Centre, Curtin University in this paper, the positioning performance of BDS/QZSS satellite navigation system has been analyzed and evaluated in aspects of the quantity of visible satellites, DOP value, multipath effect, signal-to-noise ratio, static PPP and kinematic PPP. The analysis results show that compared to BDS single system when the cutoff angle are 30°and 40°, the DOP value of BDS/QZSS combined system has decreased above 20%, and the quantity of visible satellites increased about 16–30% respectively, because of the improved spatial geometric configuration. The magnitude of satellite multipath effect of BDS system shows the trend of MEO?>?IGSO?>?GEO, which is consistent with that of QZSS satellite system, as the constellation structure of the two systems is similar. The variation tendencies of signal-to-noise ratio with respect to elevation angle of the two systems are almost the same at all frequencies, showing that at the same elevation angle the signal-to-noise ratio of MEO satellites is higher than that of IGSO satellites, as the higher obit is the lower transmitting power is obtained. For having a specially designed obit, the variation of signal-to-noise ratio of BDS system is more stable. However, the magnitude of signal-to-noise ratio of QZSS system appears the trend of frequency 3?>?frequency 2?>?frequency 1. The static PPP performance of the BDS/QZSS combination system has been improved more significantly than the BDS single system in E, N and U directions. When the cutoff angle are at 7°, 15° and 30°, the PPP accuracy is increased about 25–34% in U direction, 10–13% and 23–34% in E and N directions respectively. When the elevation angle is large (40°), compared to BDS single system at lower elevation angles (7° and 15°) the PPP accuracy of the BDS/QZSS combination system is improved above 30% in U direction. In kinematic PPP performance, compared to BDS single system, the accuracy, availability and reliability of the BDS/QZSS combination system has been improved too, especially at large elevation angles (30° and 40°), the kinematic PPP accuracy in E and U directions has been improved about 10–50%, and above 50% in U direction. It can be concluded that the combination with QZSS system can improve the positioning accuracy, reliability and stability of BDS system. In the future, with the improvement of the satellite construction of Japan’s QZSS system and the global networking of China’s BDS satellites, the QZSS satellites will contribute greatly to improve the positioning accuracy, reliability, availability and stability of GNSS systems in areas such as cities, mountains, densely-packed buildings and severely covered areas in Asian-Pacific region.     

NeQuick G model based scale factor determination for using SBAS ionosphere corrections at low earth orbit

A space-based augmentation system (SBAS) provides real-time correction data for global navigation satellite system (GNSS) users near ground. In order to use the SBAS ionosphere correction for low Earth orbit (LEO) satellites, the correction should be scaled down for the LEO altitude. This scale factor varies with ionosphere distribution and it is hard to determine the value at LEO in real time. We propose a real-time scale factor determination method by using Galileo GNSS’s NeQuick G model. A LEO satellite GPS data and SBAS data received on ground were used to evaluate the performance of the NeQuick G derived variable scale factor. The NeQuick G derived scale factor shows a significant accuracy improvement over NeQuick G model or pre-determined constant scale factor. It improves a vertical positioning accuracy of the LEO satellite. The error mean reductions of the vertical positioning over NeQuick G and the constant scale factor are 31.5% and 11.7%, respectively.     

基于GNSS的高轨卫星定位技术研究

利用全球卫星导航系统(GNSS)进行导航定位具有全球、全天候、实时和高精度的优点,应用于高地球轨道(HEO)卫星的定位,能够提供精确的轨道和姿态确定,并且可以克服目前主要利用地面测控系统对HEO卫星进行定位的设备复杂、投资高等缺点,使得自主导航成为可能.本文对利用GNSS的高轨卫星定位相关技术进行了研究,分析了单一GNSS系统和多个GNSS组合系统的卫星可见性、动态性和几何精度因子(GDOP).通过仿真分析表明,利用组合GNSS系统并通过提高GNSS接收机灵敏度的方法,可以解决GNSS进行HEO卫星定位的相关问题,并能保证HEO卫星定位精度的要求.      

A novel predictive algorithm for double difference observations of obstructed BeiDou geostationary earth orbit (GEO) satellites

Transmission link disturbances and device failure cause global navigation satellite system (GNSS) receivers to miss observations, leading to poor accuracy in real-time kinematic (RTK) positioning. Previously described solutions for this problem are influenced by the length of the prediction period, or are unable to account for changes in receiver state because they use information from previous epochs to make predictions. We propose an algorithm for predicting double difference (DD) observations of obstructed BeiDou navigation system (BDS) GEO satellites. Our approach adopts the first-degree polynomial function for predicting missing observations. We introduce a Douglas-Peucker algorithm to judge the state of the rover receiver to reduce the impact of predictive biases. Static and kinematic experiments were carried out on BDS observations to evaluate the proposed algorithm. The results of our navigation experiment demonstrate that RTK positioning accuracy is improved from meter to decimeter level with fixed ambiguity (horizontal?<?2?cm, vertical?<?18?cm). Horizontal accuracy is improved by over 50%, and the vertical accuracies of the results of the static and kinematic experiments are increased by 47% and 27% respectively, compared with the results produced by the classical approach. Though as the baseline becomes longer, the accuracy is weakened, our predictive algorithm is an improvement over existing approaches to overcome the issue of missing data.     

发射系下的SINS/CNS/GNSS组合导航UKF滤波算法

弹载系统的组合导航系统模型常建立在发射惯性坐标系下,且捷联惯性/天文导航/卫星导航（SINS/CNS/GNSS）是一种目前研究较多的组合模式。该组合导航系统的状态方程具有强非线性的特点,常用的滤波方法为扩展卡尔曼滤波（EKF）。为了提高组合导航系统的精度及可靠性,对该组合导航系统的无迹卡尔曼滤波（UKF）模型进行了设计,直接将姿态、位置与速度参数作为状态的一部分,利用CNS及GNSS提供的姿态与位置构成量测方程,并详细给出了姿态样本点的生成、均值及方差的生成过程。仿真结果表明,相对于EKF算法,采用UKF算法后各导航参数的精度可提高约20%~30%,并且系统的实时性也可以得到保证。     

2006年12月13日太阳射电暴对GPS观测的影响

日地空间环境不仅影响航天器运行和安全, 也是导航、定位和通信等无线 电应用系统主要的误差源. 其中来自太阳L波段的射电暴被认为是全球导航卫星 系统(GNSS)稳定和性能的潜在威胁因素, 当L波段射电爆发达到一定阈值时, 将给用户带来不同程度的射电噪声干扰, 严重时会引起接收机失锁和定位服务 中断. 本文对2006年12月13日太阳射电暴对GPS造成的影响进行了研究, 利用太阳射电 观测数据、L波段闪烁观测数据和向阳面不同区域的GPS观测网数据, 分析 GPS观测对射电暴的响应. 结果表明, 此次事件对GPS观测产生了明显的影响, 射 电暴期间GPS发生幅度闪烁事件和明显失锁现象, 多个台站上空的多颗GPS 卫星 信号完全中断长达6min左右, 且多个台站上空锁定的卫星数目小于4颗, 使 得GPS定位完全失效. 相对而言, 射电暴期间日下点附近的GPS台站受到的影响 比远离日下点的大.      

一种地基GNSS接收机差分码偏差估算方法

GNSS不同频点间的码伪距作差会引入信号的差分码偏差(DCB),包括GNSS卫星及地面接收机的DCB.本文提出一种地基GNSS接收机差分码偏差参数估算方法,首先由电离层文件参数作线性插值,计算出电离层延迟误差.之后对IGS站观测文件进行加权最小二乘法估计,得到GPS卫星和地面GNSS接收机的L1C频点和L2P频点间码偏...     

A MARS-based method for estimating regional 2-D ionospheric VTEC and receiver differential code bias

The geometry-free linear combination of dual-frequency GNSS reference station ground observations are currently used to build the Vertical Total Electron Content (VTEC) model of the ionosphere. As it is known, besides ionospheric delays, there are differential code bias (DCB) of satellite (SDCB) and receiver (RDCB) in the geometry-free observation equation. The SDCB can be obtained using the International GNSS Service (IGS) analysis centers, but the RDCB for regional and local network receivers are not provided. Therefore, estimating the RDCB and VTEC model accurately and simultaneously is a critical factor investigated by researchers. This study uses Multivariate Adaptive Regression Splines (MARS) to estimate the VTEC approximate model and then substitutes this model in the observation equation to form the normal equation. The least squares method is used to solve the RDCB and VTEC model together. The research findings show that this method has good modeling effectiveness and the estimated RDCB has good reliability. The estimated VTEC model applied to GPS single-frequency precise point positioning has better positioning accuracy in comparison to the IGS global ionosphere map (GIM).     

Estimation of QZSS differential code biases using QZSS/GPS combined observations from MGEX

As an important error source in Global Navigation Satellite System (GNSS) positioning and ionospheric modeling, the differential code biases (DCB) need to be estimated accurately, e.g., the regional Quasi-Zenith satellite system (QZSS). In this paper, the DCB of QZSS is estimated by adopting the global ionospheric modeling method based on QZSS/GPS combined observations from Multi-GNSS experiment (MGEX). The performance of QZSS satellite and receiver DCB is analyzed with observations from day of year (DOY) 275–364, 2018. Good agreement between our estimated QZSS satellite DCB and the products from DLR and CAS is obtained. The bias and root mean square (RMS) of DCB are mostly within ±0.3 ns. The day-to-day fluctuation of the DCB time series is less than 0.5 ns with about 96% of the cases for all satellites. However, the receiver DCB is a little less stable than satellite DCB, and their standard deviations (STDs) are within 1.9 ns. The result shows that the stability of the receiver DCBs is not significantly related to the types of receiver or antenna.     

Iridium/ORBCOMM机会信号融合定位技术

在全球导航卫星系统(GNSS)不可用情况下，低地球轨道(LEO)卫星机会信号(SOP)定位技术是一种有效的导航定位解决方案。单LEO星座机会信号定位技术面临星座构型不足或可见卫星偏少等问题，多LEO星座机会信号融合定位技术可有效解决该问题。通过分析瞬时多普勒定位原理，建立了Iridium/ORBCOMM机会信号融合定位模型，引入基于Helmert方差估计的加权最小二乘算法进一步提高定位精度。实测数据表明:基于Helmert方差估计的Iridium/ORBCOMM机会信号融合定位精度优于70 m，验证了多LEO星座机会信号融合定位的可行性和有效性。      

VLBI observations to the APOD satellite

The APOD (Atmospheric density detection and Precise Orbit Determination) is the first LEO (Low Earth Orbit) satellite in orbit co-located with a dual-frequency GNSS (GPS/BD) receiver, an SLR reflector, and a VLBI X/S dual band beacon. From the overlap statistics between consecutive solution arcs and the independent validation by SLR measurements, the orbit position deviation was below 10?cm before the on-board GNSS receiver got partially operational. In this paper, the focus is on the VLBI observations to the LEO satellite from multiple geodetic VLBI radio telescopes, since this is the first implementation of a dedicated VLBI transmitter in low Earth orbit. The practical problems of tracking a fast moving spacecraft with current VLBI ground infrastructure were solved and strong interferometric fringes were obtained by cross-correlation of APOD carrier and DOR (Differential One-way Ranging) signals. The precision in X-band time delay derived from 0.1?s integration time of the correlator output is on the level of 0.1?ns. The APOD observations demonstrate encouraging prospects of co-location of multiple space geodetic techniques in space, as a first prototype.