飞行器进近中的自适应协同传输与节点选择

针对单中继非再生放大转发(AF)的进近飞行器协同传输网络,在给出系统模型后,推导并分析了系统的输出信噪比(SNR)表达式,得到了中继节点参与协同传输的条件,提出了一种自适应的协同传输方案.目的节点判断是否采用中继传输并将结果发送到中继节点,中继节点根据接收到的信息调整传输模式.在此基础上,针对多节点正交性协同传输会显著...     

非对称衰落信道下无人机中继传输方案及性能分析

 无人机(UAV)作为中继传输平台受到了国内外研究人员的广泛关注。本文研究了非对称衰落信道下的无人机中继传输系统,提出了输出信噪比最大化准则下的波束形成(BF)优化方案,并推导出系统中断概率、遍历容量和平均误符号率等无线通信系统主要性能指标的理论表达式。通过计算机仿真验证了本文提出的中继传输方案及性能分析的正确性,并定量分析了天线数量、信道参数以及功率分配对系统性能的影响,为无人机中继传输系统的设计及性能评估提供了参考和依据。     

一种基于多无人机的中继节点布置问题建模与优化方法

针对战场环境下急需在无法通信的节点间构建有效通信链路的情形,使用多无人机作为中继节点,建立了中继节点布置(RNP)问题模型。模型以中继链路有效和无人机安全为约束,以中继布置点位置及相应的无人机为输出,不但考虑了使用的中继无人机数量,还考虑了构建中继链路花费的时间。考虑到该问题是难以求解的混合整数多目标优化问题,同时在紧急应用情形下,要求求解算法快速有效,建立了一种多项式时间中继节点布置算法(PTRPA)。仿真实验验证了所提模型确实能够在更短的时间内完成有效中继链路构建;通过Monte-Carlo方法对比和分析不同因素对PTRPA算法、随机抽样算法、遗传算法求解该问题的结果性能和时间性能的影响,验证了PTRPA算法不但能够给出接近最优的解,且快速有效,满足战场决策需求。     

基于移动Ad-hoc网络的QoS路由算法的研究

基于AODV(Ad—hoc 0n Dem and Vector)协议草案,再对助—hoc网络的QoS问题进行了深入的探讨和研究后,提出了一种“伴随式”QoS路由算法,该新算法能够适用于带有QoS业务要求的网络。并将该新算法与G reedy算法进行了比较分析,仿真结果说明新算法降低了控制消息的增加比例,并且具有较高的源节点与目的节点的连通率和较低的路径传输的延时抖动。     

空时分组编码的无人机中继通信航迹规划方法

无人机(UAV)中继通信是实现远距离点对点无线通信的一种重要技术手段。为提高无人机中继通信系统链路传输的可靠性,提出基于空时分组编码的无人机放大转发中继通信传输方案,并基于双跳链路遍历容量最大化的准则给出了无人机最佳航迹规划方法,并进一步利用FM-EM算法给出了基于空时分组编码无人机中继通信系统的中断概率及遍历信道容量计算公式。计算机仿真表明:提出的方法显著优于传统的单发单收(SISO)无人机中继通信系统。     

基于自适应步长选择的周期格型线搜索估计

稀疏、含噪观测条件下周期点过程的周期估计是一个经典的信号处理问题。针对该问题,提出了一种格型线搜索(LLS)算法,该算法通过数值方式搜索似然函数的最大值,但其性能取决于人为预先选取的搜索步长。推导了一个步长计算公式,并利用该公式改进了LLS算法。改进的LLS算法能够自适应选择搜索步长,其达到的克拉美-罗界(CRLB)的信噪比(SNR)门限与最大似然估计(MLE)算法一致,但计算复杂度比后者低一个多的数量级。性能分析与仿真实验表明,所提算法比已有算法能更好地实现估计精度与复杂度的折中。     

基于网络编码的空间DTN中CGR改进算法

随着空间通信技术的发展,卫星节点的增多,以及容延迟容中断通信需求的不断提高,空间DTN (DelayTolerant Network,容延迟网络)环境中各通信节点间的路由技术日益重要,相继出现了多种适用于DTN的路由技术.基于空间DTN的结构与特点,对CGR(Contact Graph Routing,接触图路由)算法以及基于编码的路由算法进行了分析比较,然后针对空间DTN中CGR算法的缺点和不足,研究提出了基于NC(Network Coding,网络编码)的空间DTN中的CGR改进算法(NC-CGR),并通过仿真实验平台对算法性能进行了分析评估.仿真结果表明,相比于CGR算法,NC-CGR算法在链路传输时延、传输包裹数目、中继缓存大小、链路丢包率等不同条件下的适应性方面均表现出较大优势,更适用于具有复杂拓扑、带宽受限、高动态特性的空间DTN环境.     

一种高动态低信噪比卫星导航信号捕获方法

为提升高动态低信噪比环境下卫星导航信号的捕获性能,提出了一种基于分数阶傅里叶变换(FrFT)及部分匹配滤波(PMF)的捕获方法。在该方法中,接收机首先利用PMF对接收信号做分段相干积分,随后借助快速傅里叶变换(FFT)对分段积分结果做离散快速FrFT,最后通过检测FrFT输出的峰值完成信号的捕获。由于具有多普勒频率变化率的卫星导航信号在FrFT后呈现能量聚焦特性,所提方法能够显著提高信号的长时间相干积分增益。同时对所提算法的捕获概率、平均捕获时间以及算法复杂度等性能指标进行了理论分析及计算机仿真验证。仿真表明,与传统的PMF-FFT方法相比,所提方法能够通过延长相干积分时间的方式有效提升高动态低信噪比卫星导航信号的捕获概率、降低捕获时间。     

深空中继通信束聚合效能研究

针对深空中继通信环境中BP/LTP协议加入束聚合策略对数据传输效率的影响问题,建模分析LTP数据块传输时间,考虑多会话并发及中继节点参与,获得应用数据在深空中继环境中总传输时间的期望,分析出束聚合策略对深空中继通信性能的影响。通过数值实验对不同束聚合值在典型深空中继通信环境中的效率进行了检验。结果表明:在应答链路不阻塞的约束下,越小的束聚合规模传输效率越高,且节点发送缓存大小对性能有重要影响。     

基于SA-DPSO混合优化算法的协同空战火力分配

针对超视距(BVR)多机协同空战中,火力单元采用一次性完全分配原则容易造成资源浪费的问题,提出了一种新的火力分配数学模型。该模型带有毁伤概率门限,能够保证在满足毁伤概率门限的前提下,优先保证威胁度大的目标被分配且选择对各目标相对贡献较大的火力单元,使其对目标的毁伤概率平均值达到最大且尽量少地消耗火力单元,从而节省和充分利用火力资源。在此基础上,提出采用模拟退火(SA)-离散粒子群(DPSO)混合优化算法求解协同空战火力分配,提高了算法收敛速度、精度以及全局搜索能力,避免陷入局部极小。仿真算例验证了新模型的优点以及SA-DPSO混合优化算法的有效性。     

Relay selection based on MAP estimation for cooperative communication with outdated channel state information

In this paper, we consider an amplify-and-forward (AF) cooperative communication system when the channel state information (CSI) used in relay selection differs from that during data transmission, i.e., the CSI used in relay selection is outdated. The selected relay may not be actually the best for data transmission and the outage performance of the cooperative system will deteriorate. To improve its performance, we propose a relay selection strategy based on maximum a posteriori (MAP) estimation, where relay is selected based on predicted signal-to-noise ratio (SNR). To reduce the computation complexity, we approximate the a posteriori probability density of SNR and obtain a closed-form predicted SNR, and a relay selection strategy based on the approximate MAP estimation (RS-AMAP) is proposed. The simulation results show that this approximation leads to trivial performance loss from the perspective of outage probability. Compared with relay selection strategies given in the literature, the outage probability is reduced largely through RS-AMAP for medium-to-large transmitting powers and medium-to-high channel correlation coefficients.     

FSO链路中基于平均信噪比的自适应功率传输技术

文章提出了 1种基于平均信噪比(Signal-to-Noise Ratio,SNR)的自适应功率传输技术,旨在补偿大气湍流引起的闪烁效应,以提升自由空间光(Free-Space Optical,FSO)通信系统的性能。在无需大气湍流状态信息估计的情况下,根据接收信号的平均 SNR来调整发射信号的发射功率,实现基于自适应功率传输技术的大气湍流效应补偿。建立了不同湍流强度下具有不同噪声水平的信道模型,并将所提出的技术与固定阈值判决(Fixed Threshold Deci-sion,FTD)和自适应阈值判决(Adaptive Threshold Decision,ATD)技术进行了比较分析。仿真结果表明,在不同的湍流强度下,该技术的误码率(Bit Error Rate,BER)性能相较于 FTD有了显著的提高,并且接近于 ATD。因此,该技术可以有效提高 FSO链路的通信能力。     

Proactive optimization of transmission power and 3D trajectory in UAV-assisted relay systems with mobile ground users

In this paper, an Unmanned Aerial Vehicle (UAV)-assisted relay communication system is studied, where a UAV is served as a flying relay to maintain a communication link between a mobile source node and a remote destination node. Specifically, an average outage probability minimization problem is formulated firstly, with the constraints on the transmission power of the source node, the maximum energy consumption budget, the transmission power, the speed and acceleration of the flying UAV relay. Next, the closed-form of outage probability is derived, under the hybrid line-of-sight and non-line-of-sight probability channel model. To deal with the formulated nonconvex optimization, a long-term proactive optimization mechanism is developed. In particular, firstly, an approximation for line-of-sight probability and a reformulation of the primal problem are given, respectively. Then, the reformulated problem is transformed into two subproblems: one is the transmission power optimization with given UAV’s trajectory and the other is the trajectory optimization with given transmission power allocation. Next, two subproblems are tackled via tailoring primal–dual subgradient method and successive convex approximation, respectively. Furthermore, a proactive optimization algorithm is proposed to jointly optimize the transmission power allocation and the three-dimensional trajectory. Finally, simulation results demonstrate the performance of the proposed algorithm under various parameter configurations.     

基于提前停止判决的编码软信息辅助载波同步

 针对目前编码辅助载波同步算法中复杂度较高、延时大的问题,提出了引入辅助停止判决机制的编码辅助载波同步算法。在现有的编码辅助载波同步结构基础上,该算法能对环路信噪比(SNR)进行实时判定,在环路SNR满足限定条件后提前停止编码辅助载波同步迭代,而不影响译码性能。采用新的相位估计方式估计含相位噪声的载波相位,提升了该条件下的环路信噪比。仿真采用码率为1/2的低密度奇偶校验(LDPC)码作为编码方式,结果表明:在误码率为10^-5时,该算法减少了约50%的编码辅助载波同步迭代次数;在含相位噪声的信号条件下,与理想解调译码相比,性能损失不超过0.15 dB。     

Sequential dynamic resource allocation in multi-beam satellite systems:A learning-based optimization method

Multi-beam antenna and beam hopping technologies are an effective solution for scarce satellite frequency resources. One of the primary challenges accompanying with Multi-Beam Satellites(MBS) is an efficient Dynamic Resource Allocation(DRA) strategy. This paper presents a learning-based Hybrid-Action Deep Q-Network(HADQN) algorithm to address the sequential decision-making optimization problem in DRA. By using a parameterized hybrid action space,HADQN makes it possible to schedule the beam patte...     

Energy-efficiency maximization for fixed-wing UAV-enabled relay network with circular trajectory

With the development of Unmanned Aerial Vehicles (UAVs), the applications of UAVs have been extensively explored. In the field of wireless communications, the relay nodes are often used to extend network coverage. However, traditional fixed ground relays cannot be flexibly deployed due to their low heights and fixed locations. Hence, deploying UAV as relay node is a promising solution and has become a research hotspot. In this paper, we consider an UAV-enabled relaying network in which a fixed-wing UAV is deployed between the Base Station (BS) and Ground Users (GUs). We study the energy-efficiency gap between the link “BS-UAV-GUs” and the link “BS-GUs”, and jointly optimize UAV relay transmission power and flight radius to achieve the highest energy-efficiency. Firstly, the UAV/BS-GUs channels models and the UAV energy consumption model are built. Secondly, the optimization objective function is formulated to maximize the energy-efficiency gap. Then, the solution of the optimization problem is divided into a two-step iteration process, in which the UAV relay transmission power and flight radius are adjusted to maximize the energy-efficiency gap. Finally, the experimental results under different simulation scenarios (such as cities, forests, deserts, oceans, etc.) are shown to illustrate the effectiveness of the proposed algorithm. The results show that the proposed algorithm can always find the optimal UAV relay transmission power and flight radius settings, and achieve the largest energy-efficiency gap. The convergency speed of the proposed algorithm is fast, and can obtain the optimal solution within only a few iterations.     

认知协作Ad Hoc网络中分布路由跨层控制策略

认知无线电Ad Hoc网络中,吞吐量最大化是一个关键的挑战.为了实现这一目标,协同传输是前景看好的技术,利用在每个空间节点的多样性中继链路以增加性能,特别是在无线环境中由于不同的信道质量、有限的能源和带宽资源,这种想法是有吸引力的.文章在分布式动态环境下,研究了联合动态路由.中继分配和频谱分配分布式和本地算法,提出了一...     

Relay selection in cooperative communication systems over continuous time-varying fading channel

In this paper, we study relay selection under outdated channel state information (CSI) in a decode-and-forward (DF) cooperative system. Unlike previous researches on cooperative commu-nication under outdated CSI, we consider that the channel varies continuously over time, i.e., the channel not only changes between relay selection and data transmission but also changes during data transmission. Thus the level of accuracy of the CSI used in relay selection degrades with data transmission. We first evaluate the packet error rate (PER) of the cooperative system under contin-uous time-varying fading channel, and find that the PER performance deteriorates more seriously under continuous time-varying fading channel than when the channel is assumed to be constant during data transmission. Then, we propose a repeated relay selection (RRS) strategy to improve the PER performance, in which the forwarded data is divided into multiple segments and relay is reselected before the transmission of each segment based on the updated CSI. Finally, we propose a combined relay selection (CRS) strategy which takes advantage of three different relay selection strategies to further mitigate the impact of outdated CSI.     

Optimization of beamforming and path planning for UAV-assisted wireless relay networks

Recently, unmanned aerial vehicles （UAVs） acting as relay platforms have attracted considerable attention due to the advantages of extending coverage and improving connectivity for long-range communications. Specifically, in the scenario where the access point （AP） is mobile, a UAV needs to find an efficient path to guarantee the connectivity of the relay link. Motivated by this fact, this paper proposes an optimal design for beamforming （BF） and UAV path planning. First of all, we study a dual-hop amplify-and-forward （AF） wireless relay network, in which a UAV is used as relay between a mobile AP and a fixed base station （BS）. In the network, both of the AP and the BS are equipped with multiple antennas, whereas the UAV has a single antenna. Then, we obtain the output signal~to-noise ratio （SNR） of the dual-hop relay network. Based on the criterion of maximizing the output SNR, we develop an optimal design to obtain the solution of the optimal BF weight vector and the UAV heading angle. Next, we derive the closed-form outage probability （OP） expression to investigate the performance of the dual-hop relay network conveniently. Finally, computer simulations show that the proposed approach can obtain nearly optimal flying path and OP performance, indicating the effectiveness of the proposed algorithm. Furthermore, we find that increasing the antenna number at the BS or the maximal heading angle can significantly improve the performance of the considered relay network.