Maximizing the Usable Bandwidth of MTI Signal Processors

A technique is presented for maximizing the percentage of usable Doppler bandwidth throughout which a radar return can be detected while maintaining an acceptable clutter suppression. The technique employs the weighted Chebyshev approximation to the design of a transversal high-pass digital filter which has an optimal passband ripple for a given number of filter weights and associated integration gain consistent with the required increase in signal-to-noise ratio needed for acceptable probabilities of detection and false alarm. Conventional approaches to the design of a movingtarget arget indictor (MTI) filter which maximizes the improvement factor by clutter suppression typically improve the signal-to-background noise ratio over less than 50 percent of the range between dc and the pulse-repetition frequency fT. This technique can increase the usable bandwidth to 80 percent or more of fT. Two examples are included which utilize parameter values from the Army Missile Command's experimental radar and demonstrate the interactive influence of such filter parameters as the number of weights, passband ripple and bandedge, and stopband attenuation and cutoff.     

Properties of Staggered PRF Radar Spectral Components

Expressions for moving target indicator (MTI) improvement factor limitation due to pulse repetition frequency (PRF) staggering and loss of target detectability for various values of Doppler frequency in the passband are presented. It is also shown that the product of variance of stagger periods and clutter variance is an important parameter determining the performance of a staggered PRF MTI radar.     

Design of MTI Radar on the Basis of Detection Probability

A single (quadrature) channel moving target indicator (MTI) radar system employing a tapped delay line filter is analyzed. The point of view taken is that of optimal clutter rejection in conjunction with subsequent receiver decision operations. The random nature of the spread of target Doppler shifts is taken into account. Based on the above, a procedure is presented by means of which the detection probability can be numerically evaluated for an optimized filter frequency response.     

On the Optimization of MTI Clutter Rejection

In this paper is formulated the problem of optimization of the improvement factor of a nonrecursive MTI by minimization of a quadratic form. The minimum normalized clutter output (a reciprocal of the average improvement factor) is the minimum eigenvalue of this quadratic form, and the corresponding eigenvector is the optimal weight to be used in this filter. By use of classic matrix theory, some properties of this MTI improvement factor are shown, namely, that it is bounded and is a monotonic function of the clutter spectrum variance. Also discussed is the limit of an MTI system having a large number of cancellers. Finally, the problem of a staggered-PRF MTI filter is examined, for which it is shown that its improvement factor is bounded by two equivalent constant-PRF MTI systems. One of these systems has a PRF equal to the lowest PRF of the staggered-PRF system, while the other has a PRF equal to the highest PRF of the staggered system.     

Design and Evaluation of an Adaptive MTI Filter

The design and evaluation of an adaptive moving target indicator (MTI) filter, the adaptive canceler for extended clutter (ACEC) is dealt with, taking into consideration adaptivity to clutter mean Doppler frequency. This consideration is one of the most important operational requirements in adaptive MTI's and permits a relatively simple hardware implementation as compared to more general optimization and adaptivity criteria (briefly described). The ACEC's algorithm compensates in real time for the clutter mean Doppler frequency. Performances have been obtained by digital computer simulation in various operational conditions.     

Constrained Improvement MTI Radar Processors

A new class of staggered PRF MTI radar processors is developed in this paper. These processors are constrained to achieve a specified value of MTI improvement and, subject to this constraint, minimize variations in processor response as a function of target Doppler frequency. The selection of both filter weights and PRF stagger sequences is discussed and a number of representative designs are presented.     

Correspondence - Optimum Radar Signal for Detection in Clutter

It is shown that in order to maximize the detectability of a radar target in clutter whose Doppler is unknown and is uniformly distributed over the Doppler bandwidth a simple CW or narrowband signal is optimal. The optimality criterion is the average deflection coefficient, with the averaging being over target Doppler frequency. Most remarkably the result does not depend on the clutter spectrum but holds for any distribution of clutter energy with frequency.     

Clutter suppression using recursive and nonrecursive MTI filters

The author calculates the effectiveness of clutter suppression of a moving-target-indicator (MTI) filter in tandem with a fast-Fourier-transform (FFT) Doppler filter bank, taking into account the transient response of the MTI filter. Both recursive and nonrecursive filters are considered. The analysis is extended to the high-pulse-repetition-frequency (PRF) case with clutter fold over. The results can be used to select key design parameters, including the MTI filter, the window size, and the initial transient segment to be discarded. Numerical examples are included     

On Increasing Usable MTI Filter Bandwidth by Removing Linear-Phase Constraint

It has been shown in the literature that the linear-phase constraint of finite-duration impulse-response (FIR) digital filters can, under certain circumstances, be effectively traded either for a better filter amplitude response or a reduction in the number of filter coeficients. It is shown that such a tradeoff can be exploited for moving target indicator (MTI) radar signal processors to increase the usable bandwidth for target detection. Although it is demonstrated that the increase is significant for narrowband (ground) clutter, it is negligible for wideband (weather) clutter.     

Radar/Sonar Signal Design for Bounded Doppler Shifts

In many detection and estimation problems, Doppler frequency shifts are bounded. For clutter or multipath that is uniformly distributed in range and symmetrically distributed in Doppler shift relative to the signal, detectability of a point target or a communication signal is improved by minimizing the weighted volume of the magnitude-squared autoambiguity function. When clutter Doppler shifts are bounded, this volume is in a strip containing the range axis on the range-Doppler plane. For scattering function estimation, e.g., for weather radar, Doppler flow meters, and distributed target classifiers, it is again relevant to minimize ambiguity volume in a strip. Strip volume is minimized by using a pulse train, but such a signal has unacceptably large range sidelobes for most applications. Other waveforms that have relatively small sidelobe level within a strip on the range-Doppler plane, as well as small ambiguity volume in the strip, are obtained. The waveforms are composed of pulse pairs that are phase modulated with Golay complementary codes.     

An Adaptive MTI for Weather Clutter Suppression

A digital realization of an adaptive clutter-locking loop is presented. The purpose of the loop is to estimate the mean Doppler frequency of the clutter. The clutter spectrum is then shifted toward the zero Doppler by this estimate. A fixed moving target indicator (MTI) canceler following the loop suppresses the shifted clutter. Experimental simulations illustrate the feasibility of the loop. Results indicate that the proposed canceler works significantly better than a fixed canceler, while not as well as the 10-pulse moving target detector (MTD) processor. However, the complexity of the MTD is significantly more than the relatively simple adaptive processor presented here.     

A Generalized Clutter Computation Procedure for Airborne Pulse Doppler Radars

A general procedure for analyzing ground clutter effects in airborne pulse Doppler radars is described. The quantity computed is the expected clutter power at the output of any specified range gate/ Doppler filter processing cell. The procedure has been computerized and is quite general with respect to antenna gain pattern, clutter cross section variation, PRF, pulse and range gate shapes, and the various receiver processing functions. It is applicable only to distributed ground clutter and linear processing, and excludes the dynamic effects of continuous antenna scanning. To exemplify the use of the procedure, two studies conducted for a postulated high PRF radar are described, and the results are presented.     

Clutter Covariance Matrix Form Effect on Adaptive MTI Performance

The performance of an adaptive moving target indicator (MTI), which employs a Wiener predictor by means of a transversal filter, is discussed, taking into consideration the effect of the form of the clutter covariance matrix on the MTI performance. It is emphasized that the main tap position in the transversal filter is an important factor which provides degrees of freedom in the clutter covariance matrix to improve the MTI performance. Calculation results show that by exploiting these degrees of freedom, excellent performance is feasible, in particular shorter transient response.     

Polish radar technology

Polish radar research and development since 1953 is reviewed, covering the development and production of surveillance radars, height finders, tracking radars, air traffic control (ATC) radars and systems, and marine and Doppler radars. Some current work, including an L-band ATC radar for enroute control, a weather channel for primary surveillance radar, signal detection in non-Gaussian clutter, adaptive MTI filters and postdetection filtering, and a basic approach to radar polarimetry, is examined.<>     

Measurements of L-band inland-water surface-clutter Doppler spectra

Although radar surface-clutter reflectivities from terrain are generally much greater than those from water, strong Bragg resonances at low but non-zero Doppler frequencies in backscatter from small inland bodies of water might potentially cause false alarms for moving target indicator (MTI) or other Doppler signal-processing techniques designed for target detection in ground clutter. To provide data for investigating this concern, measurements of L-band radar backscatter were recorded from the surface of a small inland freshwater reservoir in central Massachusetts. These measurements were of unusually high system stability and spectral purity so as to provide up to 80 dB of available spectral dynamic range. Strong Bragg spikes occurred in the clutter Doppler spectra from the reservoir at low (3 to 4 Hz) but non-zero Doppler frequencies. This strong Bragg resonance was persistent in time and space throughout the measurements. Spectral results are presented for all four combinations of linear polarization. Comparison with tree clutter spectral results indicates that, when an occasional water body comes under surveillance at vertical polarization in otherwise generally forested terrain, water clutter spectral density is expected to exceed surrounding-terrain tree clutter spectral densities in the Bragg-offset Doppler vicinity by large amounts     

Comparison between monostatic and bistatic antenna configurationsfor STAP

The unique characteristics of bistatic radar operation on the performance of airborne/spaceborne moving target indicator (MTI) radars that use space-time adaptive processing (STAP) are discussed. It has been shown that monostatic STAP radar has the following properties. 1) For a horizontal flight path and a planar Earth the curves of constant clutter Doppler (isodops) are hyperbolas. 2) For a sidelooking antenna geometry the clutter Doppler is range independent. 3) Clutter trajectories in the cosφ-F plane (F=normalized Doppler) are in general ellipses (or straight lines for a sidelooking array). We demonstrate that these well-known properties are distorted by the displacement between transmitter and receiver in a bistatic configuration. It is shown that even for the sidelooking array geometry the clutter Doppler is range-dependent which requires adaptation of the STAP processor for each individual range gate. Conclusions for the design of STAP processors are drawn     

Some High-Velocity Clutter Effects in Matched and Mismatched Receivers

A generalized ambiguity function including the effects of Doppler dispersion is defined as the time cross correlation of the complex envelopes of two signals, both derived from the same basic waveform but with different delays and Doppler effects. The Doppler effects include the frequency shift and expansion or contraction of the modulation time scale. This expansion or contraction is the Doppler dispersion. While the general ambiguity function cannot be expressed directly in terms of the Woodward or undispersed ambiguity function, its squared magnitude can be expressed in terms of the Woodward ambiguity function. The relation is not simple, being an integral form. Nevertheless, since the Woodward ambiguity function is known for many signals, the relation may simplify the determination of the squared magnitude of the general ambiguity function. We consider the clutter output of a matched filter or correlation receiver where the receiver is matched to a waveform having a specific delay and specific time compression. The variance of the clutter output is the two-dimensional convolution of the clutter ``scattering function' with the squared magnitude of the general ambiguity function. This is a generalization of an earlier result which is formally the same but using the Woodward ambiguity function. This last result is generalized for a mismatched receiver. In such a case, the variance of the clutter output is the double convolution of the clutter scattering function with the cross ambiguity function of the transmitted waveform, modified by the average velocity of the clutter, and the receiver reference waveform.     

Clutter rejection and transmitter-receiver requirements in anairborne radar

Ground clutter rejection requirements imposed on the exciter transmitter-receiver units of multirole airborne radar are examined. Methods are given to determine the characteristics of the units, such as noise, spurious spectral lines level, and analog-to-digital converter (ADC) dynamics, in both high- and medium-pulse-repetition-frequency modes of operation. It is shown that the spectral noise does not depend on either the wave form or the Doppler bandwidth. The reference oscillator spectral noise must be about -155 dB_c/Hz. The level of spurious lines generally depends only on the duty cycle, and the requirement is -80 dB_c for each line. ADC requires 12 to 14 b. The high-frequency mode is the most promising for detecting targets with very low radar cross sections in head-on configuration (free clutter domain)     

Optimum Processing of Unequally Spaced Radar Pulse Trains for Clutter Rejection

A train of radar pulses from one resolution cell can be processed coherently to reject echoes from external clutter and detect targets moving radially with respect to the clutter. Optimum methods of signal processing are defined for systems in which the interpulse spacings are multiply staggered to avoid target blind speeds. Likelihood ratio tests are developed for systems in which the target Doppler frequency is known a priori and for systems employing a bank of filters to cover the target Doppler band. To implement such tests, the N pulses in the train are added with complex weights and the amplitude of the sum compared with a detection threshold. The set of weights which maximizes the average signal-to-clutter ratio is also computed for a single-filter system with unknown target Doppler frequency. When the clutter autocorrelation function is exponential, the clutter covariance matrix can be inverted analytically. This latter result is useful for comparing different interpulse-spacing codes for a particular system application.     

Clutter Suppression by Complex Weighting of Coherent Pulse Trains

Uniform coherent pulse trains offer a practical solution to the problem of designing a radar signal possessing both high range and range-rate resolution. The Doppler sensitivity provides some rejection of off-Doppler (clutter) returns in the matched filter receiver. This paper considers the use of a processor in which members of the received pulse train are selectively weighted in amplitude and phase to improve clutter suppression. The techniques described are particularly suitable for rejecting interference entering the processor through ambiguous responses (range sidelobes) of the signal. The complex weights which are derived are optimum in the sense that they produce the maximum clutter suppression for a given detection efficiency. In determining these weights, it is assumed that the distribution of clutter in range and range rate relative to targets of interest is known. Thus, clutter suppression is achieved by reducing the sidelobe levels in specified regions of the receiver response. These techniques are directly applicable to array antennas; the analogous antenna problem would be to reduce sidelobe levels in a particular sector while preserving gain. Complex weighting is most successful when the clutter is limited in both range and velocity.