On Increasing Usable MTI Filter Bandwidth by Removing Linear-Phase Constraint

It has been shown in the literature that the linear-phase constraint of finite-duration impulse-response (FIR) digital filters can, under certain circumstances, be effectively traded either for a better filter amplitude response or a reduction in the number of filter coeficients. It is shown that such a tradeoff can be exploited for moving target indicator (MTI) radar signal processors to increase the usable bandwidth for target detection. Although it is demonstrated that the increase is significant for narrowband (ground) clutter, it is negligible for wideband (weather) clutter.     

Clutter Suppression by Complex Weighting of Coherent Pulse Trains

Uniform coherent pulse trains offer a practical solution to the problem of designing a radar signal possessing both high range and range-rate resolution. The Doppler sensitivity provides some rejection of off-Doppler (clutter) returns in the matched filter receiver. This paper considers the use of a processor in which members of the received pulse train are selectively weighted in amplitude and phase to improve clutter suppression. The techniques described are particularly suitable for rejecting interference entering the processor through ambiguous responses (range sidelobes) of the signal. The complex weights which are derived are optimum in the sense that they produce the maximum clutter suppression for a given detection efficiency. In determining these weights, it is assumed that the distribution of clutter in range and range rate relative to targets of interest is known. Thus, clutter suppression is achieved by reducing the sidelobe levels in specified regions of the receiver response. These techniques are directly applicable to array antennas; the analogous antenna problem would be to reduce sidelobe levels in a particular sector while preserving gain. Complex weighting is most successful when the clutter is limited in both range and velocity.     

Theory of Adaptive Radar

This paper reviews the principles of adaptive radar in which both the spatial (antenna pattern) and temporal (Doppler filter) responses of the system are controlled adaptively. An adaptive system senses the angular-Doppler distribution of the external noise field and adjusts a set of radar parameters for maximum signal-to-interference ratio and optimum detection performance. A gradient technique for control of the radar array/filter weights is described and shown to generate weights which asymptotically approach optimum values. Simulation results illustrate the convergence rate of adaptive systems and the performance improvement which can be achieved.     

An Algorithm for Designing Burst Waveforms with Quantized Transmitter Weights

An algorithm is described which finds optimum transmitter and receiver weights to maximize clutter suppression in a predetermined clutter region when using burst waveforms. It is assumed that the transmitter weights can only take on values from a finite set. This optimization problem is solved using a branch and bound algorithm. An example is given which shows the improvement in clutter suppression when this new design procedure is used as compared to a simpler nonoptimal procedure.     

机载MIMO雷达空时自适应杂波对消器

针对机载多输入多输出(MIMO)雷达杂波分布呈现空时耦合特性,提出一种空时自适应杂波对消器.利用机载MIMO雷达的脉冲回波数据,构造杂波对消器的系数矩阵.通过空时自适应杂波对消器的预处理,可以有效地抑制杂波,并通过与常规空时处理算法的级联,最终可以有效提高动目标的检测性能.实现了由传统地基雷达杂波对消器向机载运动平台的推广.仿真结果表明,这种自适应杂波对消器不仅适用于正侧视雷达,对于非正侧视雷达也同样适用.     

Optimum Processing of Unequally Spaced Radar Pulse Trains for Clutter Rejection

A train of radar pulses from one resolution cell can be processed coherently to reject echoes from external clutter and detect targets moving radially with respect to the clutter. Optimum methods of signal processing are defined for systems in which the interpulse spacings are multiply staggered to avoid target blind speeds. Likelihood ratio tests are developed for systems in which the target Doppler frequency is known a priori and for systems employing a bank of filters to cover the target Doppler band. To implement such tests, the N pulses in the train are added with complex weights and the amplitude of the sum compared with a detection threshold. The set of weights which maximizes the average signal-to-clutter ratio is also computed for a single-filter system with unknown target Doppler frequency. When the clutter autocorrelation function is exponential, the clutter covariance matrix can be inverted analytically. This latter result is useful for comparing different interpulse-spacing codes for a particular system application.     

Improved Range Resolution Filters for Rectangular-Pulse Radar Systems

The performance of several new clutter-reduction filters suitable for rectangular-pulse radar systems is investigated. The new filters consist of various approximations and modifications of two filters known to be optimal for certain criteria: the well-known Urkowitz filter which optiizes the clutter improvement ratio, and the newer sidelobe reduction filter which minimizes output noise power subject to peak sidelobe constaints. The new filters are compared usig five basic criteria: clutter improvement ratio, signal-to-noise ratio, sidelobe peak ratio, pulse compression ratio, and filter complexity. The results are summarized in tabular and graphical form.     

A Nonadaptive Processing of Radar Pulse Trains for Clutter Rejection

The problem of detecting coherent pulse trains with uniform amplitude in a clutter-plus-noise environment is considered. A radar processor for detecting targets moving radially with respect to the clutter is proposed. The minimum interpulse spacing of the transmitted signal is assumed long enough that returns are not received simultaneously from different ranges within a region of extended clutter, and the central frequency of the clutter power spectrum is postulated to be known. The processor is singled out as the linear filter, orthogonal to the clutter central frequency component, which yields the maximum ratio of peak signal power to average noise power. The filter can be implemented by slightly modifying the structure of the conventional matched filter. The performance of such a filter is compared with that achievable if full a priori knowledge of the input interference were available and with that of the conventional matched filter. This comparison is made on a signal-to-interference power ratio basis after assuming a transmitted signal consisting of equally spaced pulses and an interference characterized by an exponential covariance matrix.     

The Effect of Spectral Shape on Clutter Standard Deviation

Many radar systems now employ wideband waveforms and noncoherent averaging techniques to reduce the scintillation of the backscatter from ground clutter. The purpose of this paper is to quantify the effects of the wideband spectral shape on the clutter standard deviation after noncoherent averaging of the received signal. Relationships are developed which quantify the clutter standard deviation for any spectral shape and any ratio of transmitted band-width to processed bandwidth.     

Further results on radar pointing error reduction using discreteextended Kalman filtering

A recently proposed method of reducing target glint errors in radar systems using extended Kalman filtering is further extended with the inclusion of and compensation for clutter effects. A discrete target model and discrete Kalman filter (DKF) are used. Simulation results demonstrating the DKF are presented, and the limits on the effectiveness of the method are investigated. The major advantage of the DKF is that it can be implemented in software in the digital processor of the radar, offering flexibility over continuous time filters. The ability of the filter to reduce clutter effects further demonstrates the usefulness of this technique for radar pointing error reduction     

CFAR behavior of adaptive detectors: an experimental analysis

We conduct an experimental analysis for assessing the constant false alarm rate (CFAR) behavior of four coherent adaptive radar detectors in the presence of experimentally measured clutter data. To this end we exploit several data files containing both land, lake, and mixed land and sea clutter, collected by two radar systems (the MIT Lincoln Laboratory Phase-One radar and the McMaster IPIX radar) at different polarizations, range resolutions, and frequency bands. The results show that all the receivers, in the presence of real data, don't respect their nominal probability of false alarm (P/sub fa/), namely they exhibit a false alarm rate higher than the value preassigned at the design stage. Nevertheless one of them, the recursive persymmetric adaptive normalized matched filter (RP-ANMF) is very robust, in the sense that it presents an acceptable displacement from the nominal P/sub fa/, in correspondence of all the analyzed scenarios.     

一种基于角度-多普勒补偿的均匀圆形天线机载雷达杂波抑制方法

采用均匀圆形相控阵天线的机载雷达杂波分布随距离变化而变化,各距离单元的杂波不再满足独立同分布的条件,造成统计型空时自适应处理(STAP)器性能下降。基于此,本文建立了均匀圆形天线机载雷达模型,对其杂波分布进行了分析,得出了空间角随阵元数非线性变化的特性造成其杂波距离维分布非均匀的结论。研究了一种均匀圆形天线机载雷达杂波抑制方法,该方法先通过修正的角度 多普勒补偿(MADC)预处理消除在杂波谱中心处的非均匀,再利用基于导数更新(DBU)技术进一步减小在其他方位杂波的非均匀程度。仿真结果表明了该方法的有效性。     

基于稀疏重建的MIMO-OTH雷达多模杂波抑制算法

针对由多模传播引起的多普勒扩展杂波(SDC)严重影响天波超视距雷达(OTHR)对慢速船舰目标的检测这一问题,在基于多输入多输出体制的新一代天波超视距(MIMO-OTH)雷达系统下,利用空域信息抑制多模SDC。传统处理方法需要目标角度先验信息,而在实际中,该信息往往很难获得。为此,提出一种新的基于稀疏重建的多模杂波抑制算法。该算法将二维的稀疏角度搜索转变为一维的角度搜索,使运算量大大降低,且估计出的收发角(DOA-DOD)自动配对,同时可获得各个传播路径下信号的时间多普勒信息,达到了理想的MIMO-OTH雷达多模杂波抑制效果。仿真结果证明了所提算法的有效性。     

Modified Difference Change Detector for Small Targets in SAR Imagery

One of the most straightforward techniques for detecting changes in an image involves forming the difference between a test image and a reference image. Unfortunately, such a technique can give rise to a large number of false alarms due to the statistical variability of the underlying pixel values, as has been well established within the radar community over the years. One method for dealing with this large number of false alarms involves forming the ratio, rather than the difference, of two synthetic aperture radar (SAR) images. We introduce a modified version of the standard differencing technique to overcome problems associated with pixel value variability. The new (modified) differencing approach utilizes assumptions about the statistics of the image background and the object being sought (target) to reduce the number of false alarms due to highly variable background (clutter) regions, and it includes the standard ratio test as a special case. In fact, we find that the modified difference approach can also be viewed as a modified version of the ratio test with a threshold that varies as a function of the background clutter radar cross section (RCS). We also present an abridged, albeit suboptimal, version of this approach that eliminates assumptions regarding the target's probability distribution, and we analyze both of the approaches. We then compare these results with those obtained with a standard ratio test, and illustrate how the modified difference test reduces to the ratio test under certain operating conditions. The abridged version of the modified approach is applied to high resolution synthetic aperture radar imagery and compared with results obtained with the classical differencing technique, and following this, the modified difference technique is compared with the standard ratio test. Results suggest that under appropriate conditions the abridged, modified technique can successfully detect changes without the need for any image segmentation.     

A novel target detection approach based on adaptive radar waveform design

To resolve problems of complicated clutter, fast-varying scenes, and low signal-clutterratio (SCR) in application of target detection on sea for space-based radar (SBR), a target detection approach based on adaptive waveform design is proposed in this paper. Firstly, complicated sea clutter is modeled as compound Gaussian process, and a target is modeled as some scatterers with Gaussian reflectivity. Secondly, every dwell duration of radar is divided into several sub-dwells. Regular linear frequency modulated pulses are transmitted at Sub-dwell 1, and the received signal at this sub-dwell is used to estimate clutter covariance matrices and pre-detection. Estimated matrices are updated at every following sub-dwell by multiple particle filtering to cope with fast-varying clutter scenes of SBR. Furthermore, waveform of every following sub-dwell is designed adaptively according to mean square optimization technique. Finally, principal component analysis and generalized likelihood ratio test is used for mitigation of colored interference and property of constant false alarm rate, respectively. Simulation results show that, considering configuration of SBR and condition of complicated clutter, 9 dB is reduced for SCR which reliable detection requires by this target detection approach. Therefore, the work in this paper can markedly improve radar detection performance for weak targets.     

MTI Optimization in a Multiple-Clutter Environment

A means of optimizing a moving target indicator (MTI) filter for rejecting several types of clutter, which are generated by different mechanisms such as by rain or the ground, is formulated. lt is found that the optimal performance of such a filter depends on the spectral density functions, average radar cross sections, and the relative mean Doppler frequencies of each type of clutter. lt is shown that the optimal improvement factor of such a filter is bounded by the weighted average (weighted in accordance with the radar cross sections of the clutter types) of the improvement factor for the individual clutter type. lt is also shown that the improvement factor of such a filter is a function of the relative mean Doppler frequency f0 between the clutter types. As f0 increases, the performance of the MTI system degrades. The worst improvement factor occurs when f0 is equal to half of the radar pulse-repetition frequency (PRF).     

Nonuniform Three-dimensional Configuration Distributed SAR Signal Reconstruction Clutter Suppression

This paper deals with the problem of clutter suppression in spaceborne distributed synthetic aperture radar (D-SAR) with nonuniform three-dimensional (3D) configuration geometry. In order to make a breakthrough of the configuration limitation of the traditional space time adaptive processing (STAP) based on uniform array and improve the inhomogeneous clutter suppression performance, this paper considers signal reconstruction technique using array interpolation to process the D-SAR signal. An array interpolation signal reconstruction method based on pitching-partition is derived then a signal reconstruction 3D-STAP clutter suppression method applied to nonuniform 3D configuration is proposed. In particular, the proposed method is compared with conventional methods and the performance analysis is carried out based on simulations. The improvement factor (IF) for clutter suppression is imported and reported as a benchmark on the clutter suppression effect.     

基于杂波对消-自聚焦的多通道SAR-GMTI

对超高频(UHF)波段多通道合成孔径雷达(SAR)动目标检测技术进行研究,解决了长相干积累时间导致动目标在方位向散焦严重的问题。采用分块自聚焦技术对多通道SAR地面移动目标指示(GMTI)系统自适应杂波抑制后的SAR图像进行处理,改善杂波抑制后的SAR图像中动目标的聚焦情况,增强动目标与周围剩余杂波的对比度,进而提高恒虚警率(CFAR)检测的性能。与传统杂波抑制后直接进行CFAR检测方法相比较,该方法降低了检测虚警概率。实测数据处理结果显示动目标的信杂比明显提高,动目标方位向聚焦成功,证明了该方法的有效性。     

非高斯杂波下自适应雷达目标检测新方法

在球不变随机向量(SIRV)非高斯杂波背景下,研究了多脉冲相参雷达目标的自适应检测问题。假设杂波具有相同的协方差矩阵结构和可能相关的纹理分量,提出了新的协方差矩阵估计器,并获得了相应的自适应归一化匹配滤波器(ANMF)。理论分析表明,在估计杂波分组大小与实际情况匹配时,所获得的ANMF对杂波功率水平和协方差矩阵结构均具有恒虚警率(CFAR)特性。仿真结果表明:当估计的杂波分组大小失配时,所获得的ANMF具有近似CFAR特性,并进一步分析了不同参数变化对所提检测器性能的影响。与已有的ANMF相比,所获得的ANMF具有更好的检测性能,且迭代次数更小,其相对于已知杂波协方差矩阵的最优归一化匹配滤波器(NMF)的检测损失也更小,具有很好的实际应用前景。     

The effect of the clutter-to-noise ratio on Doppler filterperformance

The effect of the clutter-to-noise ratio on the performance of a Doppler filter is considered. Clutter is assumed to have a power level which is unknown and varies in range. The assessment of the performance of a Doppler filter is based on the gain of the filter, which is the normalized output signal-to-interference ratio improvement at a given Doppler. The gain is generally a complex function of the statistics of the clutter. New upper and lower bounds on the gain differential between the expected design point clutter-to-noise ratio and the actual clutter-to-noise ratio are found. These bounds are independent of the clutter covariance matrix and are only a function of the unknown clutter-to-noise ratio. The bounds are valid for both Gaussian and non-Gaussian noise and for arbitrary linear filters. The upper and lower bounds differ by the theoretical coherent integration gain, 10 logN dB, where N is the number of pulses. A tighter lower bound is found for the case when the filters are matched filters. A simple exact expression is found for matched filters assuming a Gaussian Markov clutter model as the clutter spectral width approaches zero. An easily implementable adaptive procedure is given which improves performance due to the unknown clutter-to-noise ratio. This work extends a previous result, valid for the Emerson filter, that shows the effect of clutter-to-noise ratio on performance in terms of an average quantity, the improvement factor