Temperature effect on buckling properties of ultra-thin-walled lenticular collapsible composite tube subjected to axial compression

This paper seeks to outline the temperature effect on the buckling properties of ultra-thin-walled lenticular collapsible composite tube(LCCT) subjected to axial compression.The buckling tests of the LCCT specimens subjected to axial compression were carried out on INSTRON-500 N servo-hydraulic machine in dry state and at the temperatures of 25 C, 100 C and 80 C. The load–displacement curves and buckling initiation loads were measured and the buckling initiation mechanism was discussed from experimental observations. Experiments show that the buckling initiation load, on average, is only about 2.2% greater at the low temperature of 80 C than at the room temperature of 25 C due to the material hardening, demonstrating an insignificant increase in the buckling initiation load, whereas it is about 19.5% lower at the high temperature of 100 C than at the room temperature owing to the material softening, implying a significant decrease in the buckling initiation load. The failure mode of the LCCT in axial compression tests at three different temperatures can be reckoned to be characteristic of the buckling initiation and propagation around the central region until rupture. The finite element(FE) model is presented to simulate the buckling initiation mechanism based on the eigenvalue-based methodology. Good correlation between experimental and numerical results is achieved.     

Effects of different aging treatments on microstructures and mechanical properties of Al-Cu-Li alloy joints welded by electron beam welding

Post-weld single aging treatment(solution treatment at 510 ℃ for 1 h, water quenching,and aging at 155 ℃ for 16 h) and post-weld double aging treatment(solution treatment at 510 ℃ for 1 h, water quenching, aging at 155 ℃ for 16 h, and aging at 130 ℃ for 12 h) are carried out on Al-Cu-Li alloy joints by electron beam welding(EBW) respectively. The effects of aging treatments on microstructures and mechanical properties of welded joints are investigated. Results show that the mechanical properties of welded joints are obviously improved after both aging treatments. The strength coefficient of joints is increased from 0.64 in an as-welded condition(AW) to 0.90 after post-weld double aging treatment. Microstructure analysis shows that the precipitates of the fusion zone within grains and grain boundaries are less in the AW condition. After post-weld heat treatment(PWHT), a lot of fine needle-like phases T_1(Al_2 Cu Li) precipitate in grain boundaries of the fusion zone, and more horseshoe-shaped β' (Al_3 Zr) particles precipitate within grains. In addition,grains of the fusion zone are refined after post-weld double aging treatment, which leads to an effect of grain refinement strengthening. Consequently, the mechanical properties of welded joints are greatly improved.     

Fatigue crack propagation of new aluminum lithium alloy bonded with titanium alloy strap

A new type of aluminum lithium alloy (Al-Li alloy) Al-Li-S-4 was investigated by test in this paper. Alloy plate of 400 mm · 140 mm · 6 mm with single edge notch was made into samples bonded with Ti-6Al-4V alloy (Ti alloy) strap by FM 94 film adhesive after the surface was treated. Fatigue crack growth of samples was investigated under cyclic loading with stress ratio (R) of 0.1 and load amplitude constant. The results show that Al-Li alloy plate bonded with Ti alloy strap could retard fatigue crack propagation. Retardation effect is related with width and thickness of strap. Flaws have an observable effect on crack propagation direction.     

Yield anisotropy and tension/compression asymmetry of a Ni3Al based intermetallic alloy

In order to investigate the yielding behavior of the newly developed Ni 3 Al-based intermetallic alloy IC10, yield stresses have been measured in tension and compression with different orientations. The specimens were cut from a sheet with different angles inclined from the solidification direction. The inclined angles were taken to be 0 , 22.5 , 45 , 67.5 and 90 . All experiments were conducted at room temperature except for orientation 0 , whose deformation temperatures ranged from 298 to 1273 K. Experimental results show that the yield strength of alloy IC10 has the anomalous behavior which has been observed for other Ll 2 -long-range ordered intermetallic alloys, but it is less pronounced. The abnormalities show the following characteristics: (i) the yield strength increases as the temperature is raised below the peak temperature, (ii) yield strength anisotropy, (iii) tension/compression asymmetry. Compared to Ni 3 Al single crystals, the polycrystalline exhibits some different yielding behaviors which may be due to the high volume fraction of c phase.     

Brazing of C/C composite and Ti-6Al-4V with graphene strengthened AgCuTi filler: Effects of graphene on wettability,microstructure and mechanical properties

Graphene nanosheets(GNSs) strengthened AgCuTi composite filler(AgCuTi_G) was used to braze C/C composite and Ti-6Al-4V. The effects of GNSs on the wettability of AgCuTi_G filler on the C/C composite surface and the interfacial microstructure and mechanical properties of brazed joints were investigated. The results indicate that the addition of GNSs reduced the wettability of AgCuTi_G. The interfacial microstructure of brazed joints evolved with the addition of GNSs, where Ti_3Cu_4 and TiCu_4 were converted to TiCu and the thickness of the reaction layer adjacent to the base material decreased. The maximum shear strength of joints brazed at 0.3 wt% GNSs was 23.3 MPa(880℃/10 min). Further adding GNSs deteriorated the shear strength of the joints. Fracture of the joints occurred in the C/C composite substrate and the TiC layer adjacent to C/C composite.     

Surface integrity and fatigue behavior when turning γ-TiAl alloy with optimized PVD-coated carbide inserts

This paper presents a comprehensive investigation on the effects of tool and turning parameters on surface integrity and fatigue behavior in turning c-Ti Al alloy. The wear of inserts surface, cutting forces, and surface roughness were studied to optimize PVD-coated carbide inserts.Surface topography, residual stresses, microhardness, and microstructure were analyzed to characterize the surfaces layer under different turning parameters. Surface integrity and fatigue life tests of c-Ti Al alloy were conducted under turning and turning-polishing processes. The results show that compared to CNMG120412-MF4, CNMG120408-SM is more suitable because it obtained low cutting force, surface roughness, and tool wear. With increasing the cutting speed and depth, the depths of the compressive residual stress layer, hardening layer, and plastic deformation layer increased. For turning and turning-polishing specimens, the compressive residual stress was relaxed by less than 20%–30% after 10~7 cycles. The fatigue life of a turning-polishing specimen with R_a= 0.15 mm has increased 3 times from that of a turning specimen with R_a= 0.43 mm.     

激光冲击强化对钛合金高温微动疲劳寿命的影响

为了解高温工作环境下激光冲击强化工艺(LSP)对钛合金材料微动疲劳寿命的影响,开展了强化前后TC11钛合金在室温、300°C和500°C下的微动疲劳试验并测试了试验件表层的残余应力及硬度。结果表明:随着温度的升高,激光冲击强化对TC11钛合金微动疲劳寿命的提高倍数逐渐减小。在轴向载荷为400MPa,法向载荷为65.5MPa时,经激光冲击强化后TC11钛合金试验件在室温、300°C和500°C下的微动疲劳寿命分别为强化前的5.5倍、3.5倍和1.7倍;强化后试验件表层的残余应力会在高温下发生松弛,且松弛程度会随温度的升高而增大,这是激光冲击强化效果随温度升高而逐渐弱化的主要原因。     

4种典型航空钛合金材料高温裂纹扩展性能对比试验

试验测定了4种典型航空钛合金材料（即TC18、TC21、TC4 DT、Ti 6Al 4V/ELI）在两种温度（25℃和250℃）下裂纹扩展性能,在试验数据的基础上,进行裂纹扩展性能对比分析,并对试样断口进行扫描电镜(SEM)分析,研究了高温和载荷联合作用对裂纹扩展的影响机理,结果表明:不同温度下，不同钛合金材料裂纹扩展速率之间存在很大的差异性；与室温断口相比,高温断口表面呈现浅黄色,并伴有大量二次裂纹；钛合金的裂纹扩展性能是受温度和载荷的联合作用影响,裂纹闭合和氧化作用共同决定了其扩展历程。      

Influences of pre-torsion deformation on microstructure and mechanical properties of pure titanium subjected to subsequent tension deformation

A series of experimental studies was carried out to investigate the influences of pre-torsion on microstructure evolution, mechanical properties, and fracture appearance of pure titanium subjected to subsequent tension deformation. An introduction of pre-torsion strain can improve the materials’ mechanical properties through micro hardness evaluation. That is, the micro hardness of tensile samples with pre-torsion deformation is much higher than that of samples processed by single torsion or tension. It can be seen from the microstructure that pre-torsion deformation can be used to refine grains better and control grains’ morphology by combining subsequent tension. The results indicate that the grains are refined most evidently for tensile samples with 2 turn pre-torsion deformation. Moreover, fracture analysis indicates that tensile samples with pre-torsion strain can present good comprehensive performance. In conclusion, pre-torsion deformation plays an important role in improving comprehensive performance and controlling microstructure evolution on pure titanium subjected to later tension deformation.     

Radical recombination in a hydrocarbon-fueled scramjet nozzle

To reveal the radical recombination process in the scramjet nozzle flow and study the effects of various factors of the recombination, weighted essentially non-oscillatory(WENO)schemes are applied to solve the decoupled two-dimensional Euler equations with chemical reactions to simulate the hydrocarbon-fueled scramjet nozzle flow. The accuracy of the numerical method is verified with the measurements obtained by a shock tunnel experiment. The overall model length is nearly 0.5 m, with inlet static temperatures ranging from 2000 K to 3000 K, inlet static pressures ranging from 75 k Pa to 175 k Pa, and inlet Mach numbers of 2.0 ± 0.4 are involved.The fraction Damkohler number is defined as functions of static temperature and pressure to analyze the radical recombination progresses. Preliminary results indicate that the energy releasing process depends on different chemical reaction processes and species group contributions. In hydrocarbon-fueled scramjet nozzle flow, reactions with H have the greatest contribution during the chemical equilibrium shift. The contrast and analysis of the simulation results show that the radical recombination processes influenced by inflow conditions and nozzle scales are consistent with Damkohler numbers and potential dissociation energy release. The increase of inlet static temperature improves both of them, thus making the chemical non-equilibrium effects on the nozzle performance more significant. While the increase of inlet static pressure improves the former one and reduces the latter, it exerts little influence on the chemical non-equilibrium effects.     

Effect of stress ratio on HCF and VHCF properties at temperatures of 20 °C and 700 °C for nickel-based wrought superalloy GH3617M

This paper attempts to investigate the effects of stress ratio and high temperature on the HCF(high-cycle-fatigue) and VHCF(very-high-cycle-fatigue) behaviors of nickel-based wrought superalloy GH3617 M. Fatigue tests over the full HCF and VHCF regimes were conducted on superalloy GH3617 M subjected to constant-amplitude loading at five stress ratios of -1, -0.5, 0,0.4, and 0.8 in environments of 20 °C and 700 °C temperatures. From experimental observation and fractographic analysis, fatigue mechanisms were deduced to reveal the synergistic interaction between high temperature and stress ratio on the HCF and VHCF behaviors of superalloy GH3617 M. A phenomenological model was crafted from available fatigue design knowledge to evaluate the synergistic interaction, and a good correlation between predictions and experiments has been achieved.     

7YSZ coating prepared by PS-PVD based on heterogeneous nucleation

Plasma spray-physical vapor deposition (PS-PVD) as a novel coating process based on low-pressure plasma spray (LPPS) has been significantly used for thermal barrier coatings (TBCs). A coating can be deposited from liquid splats, nano-sized clusters, and the vapor phase forming different structured coatings, which shows obvious advantages in contrast to conventional technologies like atmospheric plasma spray (APS) and electron beam-physical vapor deposition (EB-PVD). In addition, it can be used to produce thin, dense, and porous ceramic coatings for special applications because of its special characteristics, such as high power, very low pressure, etc. These provide new opportunities to obtain different advanced microstructures, thus to meet the growing requirements of modern functional coatings. In this work, focusing on exploiting the potential of gas-phase deposition from PS-PVD, a series of 7YSZ coating experiments with various process conditions was performed in order to better understand the deposition process in PS-PVD, where coatings were deposited on different substrates including graphite and zirconia. Meanwhile, various substrate temperatures were investigated for the same substrate. As a result, a deposition mechanism of heterogeneous nucleation has been presented showing that surface energy is an important influencing factor for coating structures. Besides, undercooling of the interface between substrate and vapor phase plays an important role in coating structures.     

Tribological evaluation of surface modified H13 tool steel in warm forming of Ti–6Al–4V titanium alloy sheet

The H13 hot-working tool steel is widely used as die material in the warm forming of Ti–6Al–4V titanium alloy sheet. However, under the heating condition, severe friction and lubricating conditions between the H13 tools and Ti–6Al–4V titanium alloy sheet would cause difficulty in guaranteeing forming quality. Surface modification may be used to control the level of friction force, reduce the friction wear and extend the service life of dies. In this paper, four surface modification methods(chromium plating, TiAlN coating, surface polishing and nitriding treatment)were applied to the H13 surfaces. Taking the coefficient of friction(CoF) and the wear degree as evaluation indicators, the high-temperature tribological behavior of the surface modified H13 steel was experimentally investigated under different tribological conditions. The results of this study indicate that the tribological properties of the TiAlN coating under dry friction condition are better than the others for a wide range of temperature(from room temperature to 500 C), while there is little difference of tribological properties between different surface modifications under graphite lubricated condition, and the variation law of CoF with temperature under graphite lubricated is opposite to that under the dry friction.     

Fatigue life prediction model of 2.5D woven composites at various temperatures

As one of the new structural layout in the family of woven composites, 2.5D Woven Composites(2.5D-WC) have recently attracted an increasing interest owing to its excellent properties, i.e. high specific strength and fatigue resistance, in the aerospace and automobile industry. Indepth understanding of the fatigue behavior of this material at un-ambient temperatures is critical for the engineering applications, especially in aero-engine field. Here, fatigue behavior of 2.5D-WC at different temperatures was numerically investigated based on the unit cell approach. Firstly, the unit cell model of 2.5D-WC was established using ANSYS software. Subsequently, the temperature-dependent fatigue life prediction model was built up. Finally, the fatigue lives alongside the damage evolution processes of 2.5D-WC at ambient temperature(20 ℃) and unambient temperature(180 ℃) were analyzed. The results show that numerical results are in good agreement with the relevant experimental results at 20 and 180 ℃. Fatigue behavior of 2.5D-WC is also sensitive to temperature, which is partially attributed to the mechanical properties of resin and the change of inclination angle of warp yarns. We hope that the proposed fatigue life prediction model and the findings could further promote the engineering application of 2.5D-WC, especially in aero-engine field.     

SCC investigation of low alloy ultra-high strength steel 30CrMnSiNi2A in 3.5wt%NaCl solution by slow strain rate technique

To evaluate stress corrosion cracking(SCC) mechanism of low alloy ultra-high strength steel 30CrMnSiNi2 A in environment containing NaCl, SCC behavior of the steel in 3.5wt% NaCl solution is investigated by slow strain rate technique(SSRT) with various strain rates and applied potentials, surface analysis technique, and electrochemical measurements. SCC susceptibility of the steel increases rapidly with strain rate decreasing from 1 · 10 5s 1to 5 · 10 7s 1, and becomes stable when strain rate is lower than 5 · 10 7s 1. SCC propagation of the steel in the solution at open circuit potential(OCP) needs sufficient hydrogen which is supplied at a certain strain rate.Fracture surface at OCP has similar characteristics with that at cathodic polarization 1000 mVSCE, which presents characteristic fractography of hydrogen induced cracking(HIC).All of these indicate that SCC behavior of the steel in the solution at OCP is mainly controlled by HIC rather than anodic dissolution(AD).     

Low-frequency unsteadiness of vortex wakes over slender bodies at high angle of attack

A type of flow unsteadiness with low frequencies and large amplitude was investigated experimentally for vortex wakes around an ogive-tangent cylinder. The experiments were carried out at angles of attack of 60–80 and subcritical Reynolds numbers of 0.6–1.8×105. The reduced frequencies of the unsteadiness are between 0.038 and 0.072, much less than the frequency of Karman vortex shedding. The unsteady flow induces large fluctuations of sectional side forces. The results of pressure measurements and particle image velocimetry indicate that the flow unsteadiness comes from periodic oscillation of the vortex wakes over the slender body. The time-averaged vortex patterns over the slender body are asymmetric, whose orientation is dependent on azimuthal locations of tip perturbations. Therefore, the vortex oscillation is a type of unsteady oscillation around a time-averaged asymmetric vortex structure.     

Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.     

Investigations on damage resistance of carbon fiber composite panels toughened using veils

This research focused on how to improve damage resistance of carbon fiber laminates. It was carried out at Cranfield University Composites Centre, Milton Keynes, UK as an MSc by research thesis project. A series of low-cost composite laminates, with or without novel veils provided by Tenax, was manufactured using current aircraft carbon fiber preforms via vacuum infusion (VI) molding in this research. All the investigations on damage resistance of these panels were carried out according to the British Standard (BS ISO 18353:2009). Initial damage was induced using a falling weight apparatus mounting a 16 mm hemispherical tip. C-scan and Micrograph were employed to reveal damage characteristics. Finally, both compression after impact (CAI) and plain compression strength were experimented. The behaviors of these panels, including damage size, damage construction, residual compression strength, and compression strength reduction, were utilized to investigate how and to what extent the veils affected the damage resistance. The results show that using veils is an efficient method of improving the damage resistance of the laminates studied. Maximum 32% increase in residual compression strength is achieved via veils accompanying with 7% increase in cost.     

Springback prediction of thick-walled high-strength titanium tube bending

Significant springback occurs after tube rotary-draw-bending （RDB）, especially for a high-strength Ti-3A1-2.5V tube （HSTT） due to its high ratio of yield strength to Young＇s modulus. The combination scheme of explicit and implicit is preferred to predict the springback. This simulation strategy includes several numerical parameters, such as element type, number of elements through thickness （NEL）, element size, etc. However, the influences of these parameters on spring- back prediction accuracy are not fully understood. Thus, taking the geometrical specification 9.525 mm × 0.508 mm ofa HSTT as the objective, the effects of numerical parameters on prediction accuracy and computation efficiency of springback simulation of HSTT RDB are investigated. The simulated springback results are compared with experimental ones. The main results are： （1） solid and continuum-shell elements predict the experimental results well; （2） for C3DSR elements, NEL of at least 3 is required to obtain reliable results and a relative error of 29% can occur as NEL is varied in the range of 1-3; （3） specifying damping factor typically works well in Abaqus/Emplicit simulation of springback and the springback results are sensitive to the magnitude of damping factor. In addition, the explanations of the effect rules are given and a guideline is added.