电子束区熔定向凝固Nb基高温合金的组织和性能

研究了Nb-Si-Ti-Hf-Cr-Al-B-Y合金在电子束区熔炉上的定向凝固组织、室温断裂韧性和高温瞬时拉伸性能.合金的组织主要由Nb基固溶体(Nbss)、α-(Nb)5Si3和(Nb)3Si相组成.定向凝固后,初生Nbss枝晶以及Nbss α-(Nb)5Si3/(Nb)3Si层片状或棒状共晶团均沿着试棒轴线定向排列.当电子枪移动速率R=2.4 mm/min时,定向效果最好.定向凝固使合金在1250℃的拉伸强度及室温断裂韧性均显著提高.R=2.4 mm/min试棒的抗拉强度最高,达85.0 MPa,同时其室温断裂韧性也达到19.4 MPa·m1/2.     

Hf对Nb15W5Si2B合金室温和高温力学性能的影响

 为了寻求Nb-Si基合金高温强度和室温塑性之间的平衡,设计了以Nb基固溶体相Nb-SS占主导的Nb15W5Si2BxHf(x= 0,5,10,15,原子百分数）合金,研究了Hf元素对Nb15W5Si2B合金的组织、室温和高温压缩性能以及高温蠕变性能的影响。结果表明,Nb15W5Si2B合金由Nb-SS和Nb5Si3两相组成,Nb5Si3相呈网状分布;Hf的加入不改变相组成,但Nb5Si3相由网状分布逐步变成不连续小岛状分布,而且体积分数减少。Hf同时提高Nb15W5Si2B合金的高温静强度和室温塑性,但对Nb15W5Si2B高温压缩蠕变性能不利。最后讨论了Hf对Nb15W5Si2B合金强化与塑性化机理。     

钇对Ti-Ti5Si3共晶合金微观组织和力学性能的影响

研究了稀土元素钇（Y）对Ti-Ti5Si3共晶合金的微合金化作用。微观组织分析表明,添加微量Y,可以改变原始钛硅合金的共晶团形态和组织形貌。适量Y的加入（原子比0．025％）,不仅使共晶团中粗大的Ti5Si3相颗粒明显细化和钝化,而且合金的微观组织也更加均匀。合金的室温压缩塑性和强度也得到了有效提高。稀土元素Y对钛硅合金的作用,很可能是因为Y原子替代了Ti5Si3相中的部分Si原子,形成硅化物Ti5（Si,Y）3所致。     

V,Al对Nb-Si系超高温结构材料抗氧化性能的影响

采用真空非自耗电弧炉制备了Nb-22Ti-12Si三元以及三种不同V,Al含量的Nb.Ti-Si-V-Al五元Nb-Si合金,研究了四种合金铸态显微组织和1250℃的抗氧化性能.结果表明:V,Al的加入促进了反应Nb3Si→Nb Nb Nb5Si3,使合金相组成由Nb Nb3Si转变成为Nb Nb5Si3,从而增加了合金中Nb相体积分数;合金的抗氧化性能随V,Al含量的增加而提高;V,Al的加入使合金氧化皮结构发生了转变,生成了较为致密的氧化皮,降低了合金的氧化速率,减少了合金氧化皮的剥落和金属氧化损失量.Nb-21.9 Ti-11.9Si-4.4V-4.1Al经过1250℃/50h氧化后金属损失厚度仅为0.1mm.     

钛硅共晶合金中硅化物及其对显微硬度的影响

观察了钛硅共晶系合金的微观组织。综合分析了X射线能谱（X－EDS）、透射电子显微镜（TEM）以及X射线衍射（XRD）结果，确认了铸态组织中析出的硅化物本质，并测得该硅化物的显微维氏硬度。结果表明，钛硅共晶合金铸态组织由α-Ti和Ti5Si3两相组成。亚共晶钛硅合金中共晶区比枝晶区具有更高的显微硬度，而共晶和过共晶合金的共晶区显微硬度明显高于亚共晶合金。     

Microstructure evolution of a hypereutectic Nb–Ti–Si–Cr–Al–Hf alloy processed by directional solidification

In this work, the Nb–14Si–24Ti–10Cr–2Al–2Hf–0.1Y alloy(at.%) was processed by the liquid–metal-cooled directional solidification(DS) at 1750 C with withdrawal rates of 1.2, 6,18 mm/min and post heat treatment(HT) at 1450 C for 10 h. The microstructures of the directionally solidified and heat treated samples were investigated. The results show that the microstructure of directionally solidified alloy mainly consists of petaloid Nbss+ Nb5Si3eutectics and Ti-rich Nbss+ Nb5Si3+ Cr2Nb eutectics. With the increase of withdrawal rate, the primary Nb5Si3is eliminated, Nbss+ Nb5Si3eutectic cells turn round and connected with the microstructure refinement and Nbss+ Nb5Si3+ Cr2Nb eutectics turn to a river-like morphology. After heat treatment,Nbss+ Nb5Si3+ Cr2Nb eutectics disappeared and petaloid Nbss+ Nb5Si3eutectics turn to a specific fiber-mesh structure gradually, which is promoted by higher withdrawal rates. Furthermore,both the volume fraction of Cr2Nb and the content of Cr in Nbssof Nbss+ Nb5Si3eutectics change regularly with the increase of withdrawal rate and heat treatment at 1450 C for 10 h.     

Cr对Nb-16Si-22Ti-2Al-2Hf合金显微组织与高低温力学性能的影响

 以Nb-16Si-22Ti-2Al-2Hf成分为基础,分别添加了2%和17%(原子分数,后同)的Cr元素替代Nb(分别称2Cr和17Cr合金),研究了Cr含量对Nb-16Si-22Ti-2Al-2Hf合金相组成、显微组织形貌、室温断裂韧性和高温强度的影响,分析了高低温失效机制。结果表明,铸态和1 375 ℃×100 h热处理后2Cr合金由Nbss和Nb₅Si₃两相组成;当Cr含量为17%时,出现了具有C15结构的Laves Cr₂Nb相,合金由Nbss、Nb₅Si₃和Cr₂Nb三相组成,热处理后在Nb₅Si₃中还析出了球状Cr₂Nb相。随着Cr含量由2%提高到17%,热处理合金的室温断裂韧性K_Q由14.32 MPa·m^1/2下降到10.30 MPa·m^1/2。合金强度与Cr含量的关系受温度影响,随Cr含量提高,室温和1 150 ℃时合金的硬度或强度增高,而1 250 ℃和1 350 ℃时合金强度降低。如1 150 ℃时2Cr和17Cr合金的屈服强度σ_0.2分别为349 MPa和387 MPa;1 350 ℃时分别为306 MPa和74 MPa。     

Nb-Si-Mo三元系合金相图

 Nb/Nb5Si3原位复合材料是一种有望替代镍基超合金用做飞机发动机叶片的新一代超高温结构材料。采用非自耗电弧熔炼技术制备出不同成分的Nb/Nb5Si3原位复合材料,利用X射线衍射仪、扫描电镜和能谱仪对Nb-Si-Mo三元系合金的相组成和微观组织进行研究。结果表明：Nb-Si-Mo三元系部分液相面投影图（<37.5 at% Si）含有4个初生相区,其立体相图中存在2个液固四相平衡反应和1个固态四相平衡反应。在2个液固四相平衡反应面之间存在一个三相共晶平衡棱柱,成分位于该棱柱内的合金会通过L→Nbss+β-Nb5Si3反应凝固生成Nbss/β-Nb5Si3片层共晶。     

Microstructure, Mechanical Properties and Oxidation Resistance of Nb-22Ti-14Si-2Hf-2Al-xCr Alloys

Nb-22Ti-14Si-2Hf-2Al-xCr (x=2, 6, 10, 14, 17 at%) alloys are prepared by arc-melting under argon atmosphere. Microstructural characteristics, mechanical properties and oxidation resistance of the arc-melted alloys are investigated. At 2 at% Cr content, the microstructure is composed of Nbss, Nb3Si and a small quantity of Nb5Si3, when the Cr contents increase, Nb3Si disappears. For the high Cr content (x ≥ 10 at%) alloys, besides the Nbss and Nb5Si3, Cr2Nb is also detected. With the increase of Cr content, the volume fractions of Cr2Nb and Nb5Si3 increase, while that of Nbss increases firstly and then begins to degrade when the Cr content is higher than 6 at%. For the alloy with 2 at% Cr, the room temperature fracture toughness is about 14.5 MPa·m1/2, but badly decreases to about 8.5 MPa·m1/2, when the Cr contents increase. Vickers hardness of Nbss tends to increase linearly from about 400 to 500, while that of silicides is not sensitive to Cr contents, about 950. The appearance of Cr2Nb phase significantly improves the high temperature oxidation resistance of the alloys with high Cr contents. The isothermal oxidation tests show that the oxidation kinetics of the alloys with various Cr contents follows parabolic oxidation kinetics.     

一种含铼和碳的镍基单晶高温合金显微组织的研究

研究了一种含铼和碳的镍基单晶高温合金的铸态和热处理态的显微组织。结果表明:合金铸态组织中枝晶干和枝晶间区域的γ'相呈近立方状,枝晶间区域析出了少量的共晶相和MC型碳化物;合金经固溶处理后,共晶相完全消除,显微偏析得到明显改善。经标准热处理后,枝晶干和枝晶间的γ'相立方度提高,枝晶干区域γ'相的体积分数和尺寸都小于枝晶间区域的,其体积分数和尺寸分别为61%,0.32μm和68%,0.41μm,而碳化物的形貌和尺寸无明显变化。合金经1095℃/100h处理后,枝晶干析出了一定量富集Re和W的TCP相。     

一种多元铌硅系原位复合材料的高温氧化行为

 采用电弧熔炼的方法制备了Nb-16Si-24Ti-6Cr-6Al-2Hf (原子百分数)多元铌硅系原位复合材料。进行了高温氧化试验，使用扫描电镜、能谱和X-射线衍射仪进行分析。结果表明该复合材料铸态组织主要由Nbss和β-Nb5Si3组成；经1250℃/100h静态氧化后，生成厚的氧化皮，其主要成分为CrNbO4，TiNb2O7；在氧化皮下发生严重的内氧化现象；氧优先在Nbss相中扩散并形成内氧化产物；硅化物对氧的扩散起到一定的阻挡作用；硅化物的分散分布有利于氧化皮中压应力的释放。     

Effects of B on the Microstructure and Oxidation Resistance of Nb-Ti-Si-based Ultrahigh-temperature Alloy

Nb-Ti-Si-based ultrahigh-temperature alloys concocted with boron ranging from 0 to 2 at% are prepared by arc-melting technology. The effects of adding boron on their as-melted microstructure and oxidation resistance are analyzed. The (Nb,Ti)ss, β-(Nb,Ti)₅Si₃ and γ-(Nb,Ti)₅Si₃ exist in Nb-22Ti-16Si-6Cr-3Al-4Hf alloy, while (Nb,Ti)ss, α-(Nb,Ti)₅Si₃ and γ-(Nb,Ti)₅Si₃ are present in Nb-22Ti-16Si-6Cr-3Al-4Hf-1B and Nb-22Ti-16Si-6Cr-3Al-4Hf-2B alloys. The oxidation of Nb-Ti-Si-based ultrahigh-temperature alloys is dominated by the diffusion of oxygen through (Nb,Ti)ss. Compared to boron-free alloys, the boron-containing alloys have significantly lower oxidation rate when oxidized at 1 200 °C for less than 50 h, but, for more than 50 h, their oxidation resistance deteriorates.     

喷射沉积A1-Si-Fe-Mn-Cu-Mg合金的微观组织与力学性能

利用喷射沉积技术制备了Al-20Si-5Fe-(0～3)Mn-3Cu-1Mg合金。借助扫描电镜(SEM)、透射电镜(TEM)、X射线衍射和拉伸试验等手段研究了喷射沉积合金的微观组织和力学性能，分析了不同Mn含量对合金组织演变的影响。结果表明，当合金中加入3％Mn时，组织中针状的Al-Si-Fe金属间化合物被颗粒状的Al     

Liquid-Solid Phase Equilibria of Nb-Si-Ti Ternary Alloys

To determine the liquid-solid phase equilibria of the Nb-Si-Ti ternary system, Nb-Si-Ti alloys of different compositions are prepared. By means of scanning electron microscopy （SEM）, X-ray diffraction （XRD） and electron probe microanalysis （EPMA）, the phases in the alloys, such as Si-based solutions, Ti（Nb）Si, Ti（Nb）Si2, Nb（Ti）Si2, Ti（Nb）5Si4, Nb（Ti）5Si3, Ti（Nb）5Si3, Nb（Ti）3Si and Nb-based solutions are identified, and the phase evolution is analyzed. As a result, the microstmctural and microchemical evidence provides a clear definition of the Nb-Si-Ti liquidus surface projection and indicates that the ternary phase diagram has seven transition reactions.     

真空吸铸TiAl基合金组织研究

利用金属型真空吸铸技术获得了TiAl基合金薄板件,并研究了该铸件的铸态组织以及合金元素对其组织的影响。实验结果表明:由于金属型的强制冷却作用,金属型真空吸铸的Ti-47Al合金薄板铸件铸态组织细小,平均晶粒尺寸在60μm左右;W元素的添加有利于B2相的形成,从而细化组织,其机理是B2相阻碍了α晶粒长大;Si元素添加生成的Ti5Si3相,主要分布在晶界处,形成的Ti5Si3第二相质点会阻碍TiAl基合金凝固过程中组织的长大,有利于细化TiAl基合金组织。     

Phase Equilibria in Nb-Si-Mo Ternary Alloys at 1 273 K and 2 073 K

Phase equilibrium in Nb-Si-Mo ternary alloys （〈37.5 at.% Si） at 1 273 K and 2 073 K is investigated by using X-ray diffraction （XRD） analysis, scanning electron microscopy （SEM） and energy dispersive spectroscopy （EDS）. The partial isothermal section at 1 273 K, which contains four single-phase regions, five two-phase regions and two three-phase regions, is basically the same as that at 1 973 K. However, when the temperature increases to 2 073 K, the three-phase region of Nbss＋ct-（Nb（Mo））sSi3＋13-（Nb,Mo）sSi3 obviously moves towards the Nb-rich comer. This suggests that Nb-Si-Mo ternary alloys remain stable at least up to 1 973 K.