共查询到20条相似文献,搜索用时 546 毫秒
1.
无人机对地自动攻击占位轨迹生成研究 总被引:1,自引:0,他引:1
基于无人机对地自动攻击过程,应用最小值原理求解了无人机对地自动攻击占位段的应飞轨迹,该方法将威胁模型、飞机运动方程和对地攻击任务有机结合,使生成的占位轨迹既能有效规避各种威胁又能为武器投放创造条件。对占位轨迹计算中的两点边值问题采用了共轭梯度法求解。通过实例仿真表明该方法是正确有效的,所得占位轨迹波动平缓没有剧烈折线现象,对占位机动研究具有一定的参考价值。 相似文献
2.
3.
针对无人机以不同载荷自主着陆时,固定的纵向参考轨迹线不能满足着陆速度及其他着陆参数对轨迹的要求的问题,文章根据无人机不同的飞行性能和着陆性能要求,设计纵向着陆轨迹,结合着陆过程的控制逻辑,设计控制律。并通过Matlab/Simulink建立无人机的自主着陆阶段的仿真模型,验证了设计的着陆轨迹和着陆控制律满足着陆性能要求。 相似文献
4.
5.
军用无人机可以用来执行各种任务,如侦察、监视、攻击、拦截等。未来战争中,军用无人机的使用将会非常广泛,正在向无人战斗机(UCAV)、多用途无人机、微型无人机、无人机集群等方向扩展 相似文献
6.
基于打靶法的战机攻击导引方法研究 总被引:1,自引:0,他引:1
在以往战机空战攻击导引研究中, 仅考虑如何导引载机使之与目标的相对距离达到武器发射射程, 没有同时考虑拦截角度的需求; 或只考虑拦截角而不考虑相对距离的需求。针对这一不足, 本文在深入分析战机攻击导引理论问题的基础上, 创新地用打靶法, 同时考虑追击距离与拦截角度两末端约束, 进行攻击轨迹优化设计。大量仿真研究表明, 所设计的攻击导引方法, 不仅能很好地满足所需的相对距离和拦截角两末端约束, 而且具有较好的可实现性。本研究可为新一代战机导引攻击系统的研制与某型飞机的国产化设计提供参考。 相似文献
7.
分析了目前高超声速飞行器的发展现状和发展趋势,指出高超武器已经给现有的防空反导武器系统带来极大威胁和挑战。针对高超声速飞行器的拦截问题,分析梳理了相关的技术难点。为保证拦截成功,采用多枚拦截器编队拦截高超声速目标是目前高效可行的技术途径,而多临近空间拦截器自主协同制导控制技术则是关键技术。针对多临近空间拦截器编队攻击自主协同制导控制技术,分别从建模、决策规划、感知、制导、控制以及评估6个方面提出需要解决的关键技术问题。最后对多临近空间拦截器编队拦截自主协同制导控制技术进行了总结与展望。 相似文献
8.
针对目标和其发射的拦截弹对来袭攻击弹进行协同拦截问题,设计了一种最优协同拦截制导律。建立描述目标、攻击弹和拦截弹三者相对运动关系的模型,引入零控脱靶量对模型进行降阶处理。考虑拦截弹对攻击弹的拦截精度、拦截末端时目标的安全性以及目标、拦截弹的控制能量问题,基于攻击弹-拦截弹零控脱靶量、攻击弹-拦截弹终端横向相对运动速度零控脱靶量、目标-攻击弹零控脱靶量以及目标和拦截弹的加速度,建立了性能指标函数,同时考虑目标和拦截弹加速度的有限性,基于极小值原理设计了最优协同拦截制导律。仿真结果表明,相比目标和拦截弹独立飞行的情况,采用协同拦截制导律,在考虑了目标安全性的前提下,机动性较弱的拦截弹能够以较平直的弹道成功拦截攻击弹。 相似文献
9.
10.
田燕妮 《海军航空工程学院学报》2005,(3)
美国北美航空航天司令部(NORAD)正在制定称之为“顶级要求文件”(CRD)的、防御来袭巡航导弹和无人机攻击的指导性文件。该文件要确定未来威胁的性质、现有能力的特点和对付未来威胁的能力特点,主要考虑的是能将各传感器和各射手联网的“系统中的系统”,提供对巡航导弹和无人机的多层防御。该文件的制定正处于最后阶段。考虑到北美海岸线很长,所有潜在的、雷达反射面很小的飞行器都可能侵入,同时缺乏对其拦截的有效武器,因此,防御来袭巡航导弹和无人机攻击是一项非常具有挑战性的任务。北美航空航天司令部的计划主管 W·霍奇金少将说,“9.11”事件之后,北美航空航天司令部的任务已经从冷战时代的监视威胁并提供重大战略告警,转为每天不停地提供航空航天领域的时间敏感目标的瞄准信 相似文献
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:3,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
13.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
14.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
15.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
16.
17.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
18.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
19.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
20.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献