共查询到20条相似文献,搜索用时 125 毫秒
1.
针对准Z源逆变器(qZSI)驱动永磁同步电机(PMSM)系统的特点,在两相静止坐标系下,提出一种有限集模型预测控制策略。由准Z源网络电容电压闭环与PMSM电磁功率前馈生成电感电流参考值,通过预测电感电流值并引入子代价函数来确定是否选择直通(ST)状态,以实现qZSI的升压控制。在非直通(NST)状态下,分别对8种开关状态下的PMSM定子电流进行预测,并与转速闭环控制生成的参考电流进行比较,选择最优的开关状态,以实现对PMSM的控制。仿真结果表明,所提控制策略可实现对qZSI的升压及PMSM转速的控制,系统具有良好的稳态及动态性能。 相似文献
2.
在基于双电流阈值的位置估计基础上,提出了一种考虑电流传感器故障和估计误差补偿的位置估计容错技术。通过双电流阈值与脉冲电流峰值比较估计位置检索脉冲信号,利用开关磁阻电机相与相之间的独立性,利用正常相的电磁信息间接估计传感器故障相的转子位置信号。通过仿真计算得到转速对位置估计误差的影响,并提出了位置误差补偿措施。在一台12/8结构样机中进行了相关试验,试验结果表明,所提方法提高了无位置传感器技术的容错性,验证了该算法的正确性和可行性。 相似文献
3.
多相电机在定子开路故障下具有良好的容错性能,与此相关的设备和控制策略改进方面的研究理论也不断被提出。然而,却少有基于统一模型的适用于多相开路故障的容错控制策略。提出了一种应用于双三相永磁同步电机(PMSM)系统三相或三相以下开路故障的容错控制策略,并获得了良好的电机电力和动态性能。针对发生单相到三相开路故障的PMSM提出了统一数学模型,提取出每种故障下对应电机不对称性的矩阵。通过电压方程,推导出每种故障对应的解耦变换矩阵。为了对相电流中的每种谐波进行无差别抑制,建立了谐波子空间。考虑开路故障相数的增加,提出了用于三相开路的有中性点电流的容错控制策略,达到了降低相电流幅值和提升系统冗余度的目的。最后通过试验和仿真结果,验证了理论分析的正确性。 相似文献
4.
5.
6.
针对永磁同步电机(PMSM)因过电压、过电流及误操作等容易造成电流传感器故障,影响PMSM的控制精度的问题,提出一种基于扩展卡尔曼滤波的PMSM无电流传感器预测控制算法。对于PMSM,通常需要两个电流传感器来采集定子电流信息,所提方法通过扩展卡尔曼滤波估计定子电流代替电流传感器。通过基于扩展卡尔曼滤波的PMSM无电流传感器预测控制算法与常规有电流传感器在线变速和变载仿真对比得到,所提方法具有和有电流传感器相同的控制性能。参数鲁棒性仿真表明,所提方法具有较强的参数鲁棒性,能够满足实际控制需要。 相似文献
7.
针对现有永磁同步电机(PMSM)转子初始位置角辨识方法存在的缺点,研究PMSM数学模型,推导电机转子位置与电机绕组电感之间的数学关系。提出利用电机三相绕组静态电感值初步判断转子位置,并用变频器发送激励电压实现转子的极性判断,进而准确辨识出转子的初始位置角。检测过程中无需转子预定位,且电机转子处于机械锁定或自由停止状态下均可实现。试验结果证明所提方法检测精度高,能够满足PMSM矢量控制的需求,具有一定的推广应用价值。 相似文献
8.
无位置传感器的中低速运行控制是开关磁阻电机研究的难点问题。为实现中低速阶段对转子位置的连续估计,提出一种基于PWM控制的无位置传感器方法。该方法将开通关断角所对应的参考信号与高频三角载波进行交截,并将得到的PWM信号作为不对称半桥功率变换器的开关管驱动信号。通过对PWM信号进行频谱分析可知,该PWM注入方式等效于注入载波频率的高频正弦信号。然后,对电流信号进行滤波及坐标变换处理,解算出连续的转子位置信息。针对电感曲线正弦度不高的问题,通过移相相减的方法消除二次谐波,简化了位置估计过程。该方法无需额外注入高频正弦信号,易于工程实现,并具备高频信号注入法的精度。最后针对一台12/8结构样机,进行了相应的仿真和实验,验证了该方法的可行性。 相似文献
9.
10.
为降低变频器供电引起的永磁同步电机(PMSM)电磁振动噪声,首先理论分析了变频器引入的PMSM振动噪声源,然后利用MATLAB/Simulink建立仿真模型,通过dSPACE进行编译并控制一台PMSM,比较了随机开关频率调制技术和死区补偿技术降低振动噪声的优缺点,提出一种混合随机开关频率死区补偿技术。试验结果表明,此方法综合随机开关频率调制技术和死区补偿技术的优点,能降低逆变器引入电流谐波引起的中低频振动噪声和逆变器开关频率与电流谐波相互作用引起的高频振动噪声。 相似文献
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:3,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
13.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
14.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
15.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
16.
17.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
18.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
19.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
20.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献