基于HSP50110、HSP50210和FPGA的机载超短波电台接收通道设计

介绍了基于软件无线电原理利用Intersil公司下变频芯片HSP50110、科斯塔斯环芯片HSP50210和FPGA芯片EP1C12实现的某机载超短波电台数字扩频接收机通道,它可以完成AM、FM、FSK、PSK等常用调制方式的下变频、同步、解调及伪码的快速并行捕获与跟踪。系统带宽8．1218MHz,用FPGA实现了一种新的全并行捕获延迟锁定环算法,捕获时间不大于一个伪码周期,抗干扰容限大于80dB。     

一种基于数据跳变检测的高动态环境GPS信号参数估计方法

鉴于高动态环境中 Ｇ Ｐ Ｓ信号参数估计和调制数据跳变检测所遇到的问题,采用扩展卡尔曼滤波方法（ Ｅ Ｋ Ｆ）对信号参数进行了估计,分析了通过载波辅助技术实现伪码延时估计的原理,重点研究了一种简单的数据跳变检测和估计参数修正方法。模拟结果表明这种方法在信号参数估计精度和动态跟踪性能等方面都能够满足高动态环境的要求。     

干扰环境下直扩系统中DMF捕获性能研究

基于数字匹配滤波器(DMF)的捕获电路具有较快的捕获速度,因此它在直扩系统(DSSS)中得到了广泛的应用。为了在干扰环境下进一步提高其捕获性能,本文对影响捕获性能的检测概率和虚警概率进行了分析;并对直扩系统中基于DMF的平均捕获时间进行了计算机仿真,从而找到了在平均捕获时间较小时应该满足的信干比、干噪比和判决门限,为改善直扩系统的捕获性能提供了理论依据。     

深空测控再生伪码测距技术研究

针对深空测控任务中低信噪比情况下的航天器高精度测距问题,对再生伪码测距技术进行论述。介绍再生伪码测距技术原理,再生伪码测距通过再生方式消除信号上行链路噪声,提高了信噪比,但需要复杂的相关器;分析再生伪码测距采用的陶思沃斯码结构,详细论述再生伪码测距信号的地面上行、星上再生、地面下行处理过程,重点介绍各处理过程中的指标条件,并对再生伪码测距进行误差分析;重点对比分析再生伪码测距与传统透明转发测距,指出前者适合于深空低信噪比条件下的高精度测距,后者适用于近地高信噪比条件下的测距。     

航天扩频测控系统抗传统测控信号干扰研究

随着扩频技术的应用,航天测控网形成了传统测控体制与扩频测控体制相结合的局面,会出现潜在的相互干扰问题。针对这种情况,运用仿真软件建立模型,根据传统测控信号经过相关器后频谱的变化,分析扩频测控系统的处理增益,并详细说明了在扩频测控信号接收带宽内距中心载波不同位置的传统测控信号对扩频测控系统处理增益的影响,以及不同扩频码速率下系统处理增益的变化情况。最后运用本文的分析成果进行举例计算。     

扩频应答机码跟踪环的一种实现方法

讨论了一种伪随机码跟踪环的特性，分析了码相关间隔、预检积分时间、环路带宽及信噪比等参数对码跟踪性能的影响。该方案不仅能够对PN码相位的变化作出调整，同时对PN码多普勒进行跟踪，较适合于测控应答机中PN码跟踪环的应用。     

扩频系统中伪码防错锁技术研究

针对扩频系统中出现的伪码错锁问题,分析了产生伪码错锁的原因,根据伪码自相关性和互相关性特点,从伪码捕获策略、错锁自动判决策略等角度研究了伪码防错锁措施：选择自相关性和互相关性尽可能好的码;合理设置捕获门限;减小多普勒捕获范围;采用并行伪码捕获方法,并在捕获过程中防止载波错捕现象发生;单独建立验证通道,进行相关值比较判决等。实践表明,采用文中方法可提高正确捕获概率,缩短捕获时间,从硬件设计上有效解决了伪码错锁问题。     

基于DSP的高动态数字解扩接收机的研究

讨论了高动态、低信噪比、长伪码序列扩频信号的伪码捕获、跟踪、载波跟踪与数据解调方法。提出了一种基于高速数字信号处理技术和现场可编程逻辑器件 ( FPGA)的全数字高动态解扩接收机方案。     

基于VHDL语言的扩频相关器设计与实现

介绍了扩频相关器在信号处理中对特定码字进行相关处理,完成信号的解扩或解码,恢复出传送的信息.扩频相关器采用数字处理方式,处理信号的形式比较灵活,可以对不同的码型、不同的码长进行相关处理,为位同步的提取带来了极大的方便.设计了包含相关器的整个直扩系统,并进行了仿真,验证了所设计的相关器的正确性.     

Performance analysis of GPS carrier phase observable

The accuracy analysis of Global Positioning System (GPS) carrier phase observable measured by a digital GPS receiver is presented. A digital phase-locked loop (DPLL) is modeled to extract the carrier phase of the received signal after a pseudorandom noise (PRN) code synchronization system despreads the received PRN coded signal. Based on phase noise characteristics of the input signal, the following performance of the first, second, and third-order DPLLs is analyzed mathematically: (1) loop stability and transient process; (2) steady-state probability density function (pdf), mean and variance of phase tracking error; (3) carrier phase acquisition performance; and (4) mean time to the first cycle-slipping. The theoretical analysis is verified by Monte Carlo computer simulations. The analysis of the dependency of the phase input noise and receiver design parameters provides with an important reference in designing the carrier phase synchronization system for high accuracy GPS positioning     

Predicting and adapting satellite channels with weather-induced impairments

Efficiency improvements using predictive and adaptive methods over satellite channels with weather-induced impairments are presented. Scintillation and rain attenuation are the two dominant factors for signal fading over satellite-Earth paths at operating frequencies over 10 GHz. We develop statistical and spectral analyses of these processes, and obtain simple linear predictors for received signal attenuation using autoregressive (AR) models. For adaptation, we propose changing signal transmission power, modulation symbol size, and/or code rate as the state of the channel changes. In particular, we introduce a continuous power control and discrete rate control strategy. Quantitative analyses of power consumption and channel capacity indicate that there can be a substantial gain in performance with such adaptive schemes.     

单载波干扰对星载扩频应答机码跟踪回路影响研究

扩频码同步是基于扩频体制卫星测控通信中的一项关键技术。研究单载波对星载扩频应答机中全时间超前-滞后非相干跟踪回路的影响,分析单载波干扰存在时跟踪抖动的恶化程度,给出相应的数学表达式,并进行了Matlab仿真。仿真结果表明：在一定的跟踪回路带宽下,恶化程度随着系统的扩频增益或频偏的增加而减小,并随着干信比的增加而增加。单载波干扰不变的前提下,恶化程度随着回路带宽的增加而增加。     

扩频通信系统伪码相位跟踪环性能研究

在现代通信系统中,对于全数字化扩频接收机来说,由于伪码跟踪环中鉴相器具有非线性特性,所以有可能使扩频通信环路工作在非线性区域。本文分析了一种非相干伪码跟踪环路的线性以及非线性跟踪性能,并得到了环路的收敛域与收敛条件,这些分析结果对环路参数的设计都是至关重要的。     

A new algorithm to optimize Barker code sidelobe suppressionfilters

The authors suggest a new algorithm for binary coding waveform sidelobe reduction after matched filtering and present a general method by which optimized sidelobe suppression filters for Barker codes can be obtained with a peak output sidelobe 2.62 dB lower than the results found in the literature (for 13-b Barker code). This optimization algorithm is also promising for other binary coding waveforms, such as truncated pseudonoise (PN) sequences and concatenated codes. This new approach can readily be applied to sidelobe-reduction filter design for other binary coding waveforms, such as truncated PN sequences, concatenated codes, etc., which often find their applications in radar systems and spread spectrum communication systems     

Imaging of a compact range using autoregressive spectral estimation[radiation patterns measurement]

The spurious scattering mechanisms of a compact range, which cause spurious signals as well as the desired plane wave to illuminate the test zone, are addressed. It is shown that an accurate estimation of the direction-of-arrival and amplitude of spurious signals in a compact range is beyond the resolution available from the Fourier transform. An estimation technique based on autoregressive (AR) modeling of field probe data is developed to locate and quantify the spurious signal sources. The probe aperture is divided into a number of overlapping subapertures so that the far-field criterion for each subaperture is satisfied. Then, the subaperture data are modeled as an AR process. Singular value decomposition and forward-backward linear prediction are used to estimate the model order and the AR parameters. Examples of probe measurements and analysis for an actual compact range are given     

基于二相编码的探测干扰一体化信号波形设计与仿真

如今,在信号处理技术飞速发展的背景下,针对传统的雷达信号设计暴露出的功能单一、低截获性能差以及距离速度分辨力较低等问题,构建了 1种基于十三位巴克码的探测干扰一体化信号波形。文中对其调制原理进行了分析,对其中的二相编码序列分量、伪随机码序列分量进行自相关函数特征分析,并分别从模糊函数、功率谱角度分析其探测特性和干扰特性。仿真实验证明,探测干扰一体化信号样式相较于单一调制的十三位巴克码信号具有较好的模糊函数和功率谱特性,在保持二相编码信号良好的多普勒敏感特性基础上,具有更好的距离分辨力以及更 大的干扰带宽。     

A Parametric Technique for Time Delay Estimation

The problem of estimating the time difference of arrival of a signal with unknown spectrum to two receivers is treated. A signal model containing both spectral and delay parameters is derived. The model parameters are computed by a two-step procedure: (1) the modified Yule-Walker equations are used to estimate the autoregressive spectrum of the source signal, and (2) a frequency domain squared error criterion is minimized to provide the delay estimate. The performance of the proposed technique is illustrated by simulation results.     

GPS选择可用性(SA)信号采集与建模

 分析了ＧＰＳ测量伪距的各组成部分,设计了一个ＧＰＳ数据实时采集系统,通过定位计算和时钟偏移滤波的方法分离ＳＡ误差信号,经检验指出ＳＡ误差信号基本是零均值的平稳随机过程,对一段时期定点观测到的ＳＡ误差信号进行ＡＲ（１３）的模型辨识,获得大量的模型数据,从时域和频域对模型参数进行分析得到一些有益的结论。     

Modeling and analysis for the GPS pseudo-range observable

In this paper, a digital system for the Global Positioning System (GPS) pseudo-range observable is modeled and analyzed theoretically. The observable is measured in a GPS receiver by accurately tracking the pseudorandom noise (PRN) code phase of the input GPS signal using a digital energy detector and a digital delay lock loop (DDLL). The following issues are presented: (1) mathematical modeling of the digital PRN code acquisition and tracking system, (2) the closed-form expression derivation for the detection and false-alarm probabilities of the acquisition process and for the variance of code phase tracking error, and (3) the linear and nonlinear performance analysis of the DDLL for optimizing the receiver structures and parameters with tradeoff between the tracking errors due to receiver dynamics and due to input noise     

Detectability of Spread-Spectrum Signals

Methods of detecting spread-sprectrum signals without knowledge of the pseudorandom code used to generate the signal are described. Exact and approximate methods of calculating relationships among detection probability, false alarm rate, and signal-to-noise ratio are given for radiometers and for channelized pulse-detection systems. The detection performance of the radiometer is compared graphically with that of pulse-detection systems, for two different kinds of pulse detection decision rules. Detection performance as a function of certain signal parameters is shown to be very different for a pulse-detection system than for a radiometer, and this difference in behavior provides a basis for selecting signal parameters that minimize the probability of detection. The reasoning that underlies the selection process is explained, and the process is outlined for each of several signal parameters.