Precision Synchronization of Satellites in Inclined Orbits

Synchronization between an Earth station and a satellite in geostationary orbit can be accomplished by repeatedly transmitting sync burst signals and making small timing corrections. However, when a satellite is in an inclined nonsynchronous orbit, such as a navigation satellite, the problem is more complex due to the high relative velocity of the navigation satellite relative to the ground. One possible solution to the problem is examined by employing a satellite in geostationary orbit to communicate with the navigation satellite. It is shown that the uplink delay to the navigation satellite can be deduced to an accuracy of about 1 ns by making a single round trip transmission.     

Genetic algorithm application to efficient utilization of the GSO

Utilization of the geostationary satellite orbit (GSO) has reached full capacity in orbital arcs at certain longitudes. A variety of proposals and regulations have already been established to increase the number of possible satellite positions. The optimum satellite arrangement carried out by considering the geographical distribution of service areas is an effective strategy for efficient utilization of the GSO. The genetic algorithm (GA) method is applied here to optimize the satellite arrangement. Initially, an example of the optimum arrangement of eight satellites is demonstrated by using the GA method to ensure accuracy of the newly developed program. Subsequently, a multiple beam satellite system concept is introduced to further improve the efficient utilization of the GSO. Finally, 80 satellites (40 service areas) in the ITU Region 1 example is solved using the GA method, resulting in a quasi-optimum satellite arrangement solution. By using the GA method, the quasi-optimum solution can be obtained by very short (e.g., several ten seconds) calculation times.     

Theoretical Bounds on Random Errors in Satellite Doppler Navigation

Analytic expressions of the random errors in a satellite Doppler navigation system are developed. The errors in the along-track and across-track coordinates are expressed as functions of the geometry (range and angle), pass-length, and signal-to-noise ratio (SNR). Such an analytic result becomes possible due to an explicit solution to a simplified rectilinear model of the satellite pass over a flat Earth. It is shown that the explicit solution performance in the presence of noise is identical to that of the iterative solution, used in the real navigation problem.     

基于气压高度辅助的机载自主完好性监测算法

卫星接收机自主完好性监测是指根据用户接收机的多余观测值监测用户定位结果的完好性,其目的是在导航过程中检测出发生故障的卫星,并保障导航定位精度。针对卫星接收机自主完好性监测算法可用性不足的问题,结合机载实际导航系统配置,提出了一种基于气压高度表辅助的机载自主完好性监测算法。综合利用卫星导航系统及气压高度表观测信息,建立联合系统的观测模型,推导了基于多解分离的完好性监测及保护级别计算方法。仿真结果表明,相比于传统的接收机自主完好性监测算法,该算法在可见星为5颗时仍能识别故障卫星。该算法具有更好的故障检测能力及可用性,能有效提高卫星导航系统的完好性监测性能,从而保证卫星导航系统的精度和可靠性。     

Cross-layer design of LT codes and LDPC codes for satellite multimedia broadcast/multicast services

According to large coverage of satellites, there are various channel states in a satellite broadcasting network. In order to introduce an efficient rateless transmission method to satellite multimedia broadcasting/multicast services with finite-length packets, a cross-layer packet transmission method is proposed with Luby transform （LT） codes for efficiency in the network layer and low density parity check （LDPC） codes for reliability in the physical layer jointly. The codewords generated from an LT encoder are divided into finite-length packets, which are encoded by an LDPC encoder subsequently. Based on noise and fading effects of satellite channels, the LT packets received from an LDPC decoder either have no error or are marked as erased, which can be mod- eled as a binary erasure channels （BECs）. By theoretical analysis on LT parameters and LDPC parameters, the relationships between LDPC code rates in the physical layer and LT codes word lengths in the network layer are investigated. With tradeoffs between the LT codes word lengths and the LDPC code rates, optimized cross-layer solutions are achieved with a binary search algorithm. Verified by simulations, the proposed solution for cross-layer parameters design can provide the best transmission mode according to satellite states, so as to improve throughput performance for satellite multimedia transmission.     

Global Gravity Field Recovery Using Solely GPS Tracking and Accelerometer Data from Champ

A new long-wavelength global gravity field model, called EIGEN-1, has been derived in a joint German-French effort from orbit perturbations of the CHAMP satellite, exploiting CHAMP-GPS satellite-to-satellite tracking and on-board accelerometer data over a three months time span. For the first time it becomes possible to recover the gravity field from one satellite only. Thanks to CHAMP'S tailored orbit characteristics and dedicated instrumentation, providing continuous tracking and on-orbit measurements of non-gravitational satellite accelerations, the three months CHAMP-only solution provides the geoid and gravity with an accuracy of 20 cm and 1 mgal, respectively, at a half wavelength resolution of 550 km, which is already an improvement by a factor of two compared to any pre-CHAMP satellite-only gravity field model. This revised version was published online in August 2006 with corrections to the Cover Date.     

全球精密单点定位性能评估

随着中国北斗三号卫星导航系统（BDS-3）全面建成与开通，北斗卫星导航系统已步入了新发展阶段，基于BDS-3实现全方位、多层次、高精度应用已成为地学研究中一项基本任务。利用全球最新均匀分布的10个MGEX跟踪站，分别从24 h内接收到的卫星数、卫星位置精度因子（PDOP）、卫星数据解算完整率和双频非组合精密单点定位（PPP）静态/动态定位精度等方面系统深入地评估了BDS-3在全球范围内的可用性。结果表明，测站对卫星跟踪能力与配备的接收机类型和区域位置有强相关性，单BDS-3卫星在全球范围内具有较强的连续定位能力，当使用SEPT POLARX5和JAVAD TRE_3接收机的情况下，数据解算完整率可达100%。此外，水平方向和高程方向定位精度分别优于2 cm和3 cm，并且在联合使用BDS-2和BDS-3定位的条件下，可使得静态定位精度在东、北和高程方向进一步提升37.6%,25.3%和38.9%。     

GNSS卫星钟差估计与结果分析

探讨了GNSS卫星钟差估计的基本原理、处理方法及数据处理中的一些关键技术,利用全球56个IGS跟踪站的观测数据进行钟差估计,比较分析了钟差产品的精度与定位性能。以GPS系统解算结果为例,其钟差产品与IGS最终精密卫星钟差符合较好,精度优于0.04ns(约0.012m),多系统钟差解算结果互差优于亚纳秒级。基于钟差产品进行精密单点定位解算试验,试验结果表明,在定位收敛之后,静态PPP在东、北、天3个方向上精度为0.0582m、0.0466m、0.1188m;动态PPP在东、北、天3个方向上精度为0.0671m、0.0640m、0.3200m。定位结果与IGS最终精密钟差解算结果符合较好,表明两者之间差异较小,进一步验证了解算得到的卫星钟差产品的定位性能。     

基于中继测量的环月探测器定轨能力分析

嫦娥四号月球探测拟首次实现月球背面的软着陆,测控与数传依赖地月L2平动点的中继卫星,并有望获取四程测量与星间测量数据。对基于中继测量的环月探测器测定轨能力进行了仿真分析,结果表明,中继卫星可较好地实现环月探测器连续跟踪;在定轨能力方面,中继卫星自身轨道精度是制约环月探测器定轨精度的重要因素,当跟踪弧段达到5h以上时,定轨精度趋于稳定,但轨道精度较中继卫星的轨道精度相差1个量级;对于星间链路测量,除中继卫星自身的轨道精度外,星钟的稳定性是制约定轨精度的另一个重要因素,如果辅助以每天1h的地基跟踪亦可实现优于百m的定轨精度。     

基于协同进化粒子群和Pareto最优解的卫星编队队形重构方法

针对卫星编队自主队形重构问题,提出了基于协同进化粒子群优化(CPSO)和Pareto最优解的求解方法.首先,使用Legendre伪谱法(LPM)将队形重构问题离散化为非线性规划(NLP)问题;其次,根据卫星编队的特点及碰撞规避的需要,使用CPSO算法对重构问题采用既独立又集中的求解方式,避免了传统优化方法对梯度的求解;...     

Impact of one satellite outage on ARAIM depleted constellation configurations

Advanced Receiver Autonomous Integrity Monitoring(ARAIM) is a new technology that will provide worldwide coverage of vertical guidance in aviation navigation. The ARAIM performance and improvement under depleted constellations is a practical problem that needs to be faced and researched further. It is a shortcut that improves the availability in position domain whose key idea is to replace the conventional least squares process with a non-least-squares estimator to lower the integrity risk in exchange for a slight increase in nominal position error. The contributions given in this paper include two parts: First, the impacts of one satellite outage on different constellations are analyzed and compared. The conclusion is that GPS is more sensitive and vulnerable to one satellite outage. Second, a constellation weighted ARAIM(CW-ARAIM)position estimator is proposed. The position solution is replaced by a constellation weighted average solution to eliminate the constellation difference. The new solution will move close to the constellation solutions with respect to the accuracy requirement. The simulation results under baseline GPS and Galileo dual-constellation show that the one GPS satellite outage will knock the availability from 91% to only 50%. The performance remains stable with one Galileo satellite outage. With the assistance of the CW-ARAIM method, the availability can increase from 50% to more than80% under depleted GPS configurations. Even without any satellite outage, the proposed method can effectively improve the availability from 91.29% to 98.75%. The test results under optimistic constellations further verify that a balanced constellation is more important than more satellites on orbit and the superiority of CW-ARAIM method is still effective.     

Beam Area Determination for Multiple-Beam Satellite Communication Applications

An exact analytical model and a simple numerical solution are presented for determining the surface area of the Earth illuminated by a conical beam, with an elliptical cross section, emanating from a satellite. The model is used to generate sets of parametric curves for determination of the beam area as a function of the different satellite locations, beam locations, and beamwidths. Numerical results show that for a circular beam with a 0.25° beamwidth, the beam illuminating the northern Continental United States (CONUS) can cover an area about five times larger than the area covered by the same size beam illuminating the southern CONUS. Comparisons are also made with the available approximate methods.     

基于改进POCET技术的通导一体化信号设计

随着低轨卫星组网的发展,结合我国北斗三号全球卫星导航系统的全面建成,研究兼容北斗的通信导航一体化技术日益迫切。为使卫星上的高功率放大器工作在非线性饱和区,以达到较高的发射功率效率,需要保证合成信号的恒包络特性。考虑北斗导航信号与低轨卫星通信信号频点不同,且待复用信号分量较多,以相位优化恒包络发射(POCET)技术为基础,提出了一种改进的多频点多非独立信号分量恒包络复用技术,对七路信号进行复用,利用罚函数进行目标函数优化得到最优解。通过分析其信号特性,表明该方法具有较高的复用效率,并能有效抑制非独立分量造成的波形畸变,从而实现通信导航一体化信号设计,为未来基于低轨卫星的通信导航一体化波形设计提供了思路。     

基于改进POCET技术的通导一体化信号设计

随着低轨卫星组网的发展,结合我国北斗三号全球卫星导航系统的全面建成,研究兼容北斗的通信导航一体化技术日益迫切。为使卫星上的高功率放大器工作在非线性饱和区,以达到较高的发射功率效率,需要保证合成信号的恒包络特性。考虑北斗导航信号与低轨卫星通信信号频点不同,且待复用信号分量较多,以相位优化恒包络发射（POCET）技术为基础,提出了一种改进的多频点多非独立信号分量恒包络复用技术,对七路信号进行复用,利用罚函数进行目标函数优化得到最优解。通过分析其信号特性,表明该方法具有较高的复用效率,并能有效抑制非独立分量造成的波形畸变,从而实现通信导航一体化信号设计,为未来基于低轨卫星的通信导航一体化波形设计提供了思路。     

大偏心率火星探测器轨道外推的近似方法

对于快自转天体,如地球和火星,由于其非球形引力位中田谐项的振动频率与卫星运动频率相当,会给构造大偏心率环绕型探测器轨道分析解带来无法克服的困难。本文以轨道偏心率e≈0.9的＂萤火虫一号＂（YH-1）火星环绕探测器为例,探讨在精度要求不高的情况下,给出近似分析解和计算效率与其相当的数值解计算方案,以满足在计算资源有限的制约下快速轨道外推的要求。     

卫星MEMS热控系统的动态特性及自主控制策略

在卫星热控系统中将高效冷却技术与系统层次的智能控制策略相结合是完成航天热控任务的理想候选方案。针对一种基于微机电系统(MEMS)的微槽道换热器和微百叶窗在卫星主动热控系统中应用的方案,应用集总参数法建立了受控对象的系统动态响应模型;提出了一种引入外热流协调因子和专家智能整定比例-积分-微分(PID)控制相结合的自主温度控制策略;完成了其在纳卫星上应用效果的仿真研究。仿真结果表明:自主温度控制策略能够根据当前的控制局势及变化趋势对多个被控量进行自主协调,不但能够有效满足星载电子设备的苛刻温控要求,同时也是实现卫星高度自主飞行的关键技术之一;该温度控制策略同样适用于其他控制场合。     

基于非合作低轨卫星的测向交叉定位技术

根据非合作低轨卫星的特点，可以被动测量多颗卫星信号的来向，通过测向交叉的方式进行定位。但是通过星历解算出的卫星位置位于地心地固坐标系，用户测量的方位角和俯仰角基于站心坐标系。针对非合作低轨卫星测向交叉定位时目标用户角度信息与卫星位置基于不同坐标系的问题，提出了一种迭代最小二乘定位算法，通过迭代的方式不断收敛定位结果，能够在目标用户角度信息与卫星位置基于不同坐标系的情况下，解决非合作低轨卫星的测向交叉定位问题。仿真结果表明，基于迭代最小二乘定位算法能够实现非合作低轨卫星仅利用角度定位，并分析了测角精度、卫星轨道高度、参与定位卫星数与定位误差之间的关系。针对迭代的计算方法，分析了迭代过程中不同收敛条件下迭代次数与定位误差之间的关系。在保证定位精度的情况下，将迭代收敛范围设置为8~30 km，可以降低2~3次迭代次数。     

带时变通信时间延迟的卫星编队姿态协同自适应L2增益控制

针对卫星编队姿态协同分布式控制问题,提出一种基于Lyapunov方法的编队飞行协同控制策略.首先,考虑到实际编队飞行中星问通信存在时变时间延迟及模型不确定问题,结合变结构控制的思想设计一种针对时滞系统稳定性分析的Lyapunov函数,从而由直接Lyapunov方法得到可对模型参数进行估计的自适应分布式姿态协同控制器,并...     

关于地球卫星运动中的坐标系附加摄动问题

关于卫星运动中的坐标系附加摄动，早期是从两种赤道坐标系中卫星轨道根数的差别采用大量球面三角公式的方法导出的，本文将改用与当今高精度数值解中的坐标转换关系，在岁差章动等参数完全一致的情况下，简要清晰地导出相应的坐标系附加摄动解，既容易被读者接受，又便于与对应的数值解进行比对。     

Stabilization of a Satellite via Specific Optimum Control

The Optimum Stabilization of a tumbling satellite via Hamilton-Jacobi theory has been reported by one of the authors before in ?On the optimum stabilization of a satellite? [2]. This companion paper discusses the synthesis of a specific optimum control law for the same problem and compares the results with the optimum solution. It is shown that a specific optimum control law yields, acceptable performance while being much easier to instrument than the optimum control law.