A satellite interference location system using differential timeand phase measurement techniques

The design and development of a system for inferring the position of terrestrial satellite uplink stations using existing domestic satellites with minimal disruption to normal satellite operation are described. Two methods are presented by which a quantity measured at a terrestrial receiving site is mapped into a curve of possible uplink locations on the Earth's surface. One method involves measuring differential time delays of a single uplink signal observed through two adjacent spacecraft. The other uses a short baseline interferometer composed of the two cross-polarized and spatially separated antenna feeds aboard an affected satellite. A unique location is obtained by using an appropriate combination of the two methods. A system for measurement of the required differential delays and phases and experimental work performed to demonstrate the feasibility of the location methods are described     

Time delay techniques for satellite interference location system

Describes the development of a system for inferring the position of uplink ground stations, using existing domestic satellites, with minimal disruption of normal operation. The system uses the differential time delay of a single uplink signal passing through two adjacent spacecraft to infer the relative position of the uplink transmitter. A system for the measurement of such differential time delays is described. Since this technique alone does not provide an unambiguous determination of uplink transmitter location, the use of an interferometer to resolve such ambiguities is discussed     

Sensitivity analysis of dual-satellite geolocation

An analytic solution is presented for the linearized estimation problem arising from the dual-satellite geolocation of the source of a narrowband signal using time- and frequency-difference-of-arrival (TDOA and FDOA, respectively) observations and an altitude constraint. This solution is used to analyze the covariance matrix of the resultant source location estimate, along with the sensitivity of its mean to errors in the presumed source altitude and velocity, and the measured or predicted positions and velocities of the satellites. Following the practice of differential Global Positioning System, the technique of differential calibration is used to reduce or eliminate various sources of solution bias which would otherwise require tight, and consequently expensive, individual calibration     

Target localization based on cross-view matching between UAV and satellite

Matching remote sensing images taken by an unmanned aerial vehicle (UAV) with satellite remote sensing images with geolocation information. Thus, the specific geographic location of the target object captured by the UAV is determined. Its main challenge is the considerable differences in the visual content of remote sensing images acquired by satellites and UAVs, such as dramatic changes in viewpoint, unknown orientations, etc. Much of the previous work has focused on image matching of homologous data. To overcome the difficulties caused by the difference between these two data modes and maintain robustness in visual positioning, a quality-aware template matching method based on scale-adaptive deep convolutional features is proposed by deeply mining their common features. The template size feature map and the reference image feature map are first obtained. The two feature maps obtained are used to measure the similarity. Finally, a heat map representing the probability of matching is generated to determine the best match in the reference image. The method is applied to the latest UAV-based geolocation dataset (University-1652 dataset) and the real-scene campus data we collected with UAVs. The experimental results demonstrate the effectiveness and superiority of the method.     

Solution and performance analysis of geolocation by TDOA

One method of geolocation is based on measuring the time difference of arrivals (TDOAs) of a signal received by three or four geostationary satellites. The received signals are cross-correlated to determine the TDOAs and a set of nonlinear equations are solved to produce the location estimate. An exact solution for the transmitter position is derived for the three or four receiver cases. Extension of the solution method to more receivers is straightforward. An analysis of the performance of the system is given, together with expressions for predicting the localization mean-square errors (MSEs) and bias, and the Cramer-Rao bound. Both precision in TDOA measurements and the relative geometry between receivers and transmitter affect the localization accuracy. The geometric factors act as multipliers to the TDOA variance in the bias and MSE formulae. A study of the dependency of the geometric factors on transmitter position and satellite spacings are provided, as well as simulation results     

基于LAS码的星群多目标测控技术研究

针对星群多目标同时测控问题,基于星群轨道根数的时延特性和多普勒频移特性分析可得,星群多目标测控的上行链路遥控与测距信号可实现S CDMA（Synchronous Code Division Multiple Access,同步码分多址）,由于星间距离较小,下行链路遥测与测距信号满足QS CDMA（Quasi synchronous code division multiple access,准同步码分多址）.上行链路遥控和测距信号形式设计为PCM BPSK CDMA（Pulse Code Modulation Binary Phase Shift Keying Code Division Multiple Access,脉冲编码调制二进制相移键控码分多址）,上行链路信号采用Gold序列扩频;下行链路遥测和测距信号形式设计为PCM BPSK CDMA,根据总的时延差,提出下行链路采用基于等长脉冲间隔法构造的LAS（Large Area Synchronous,大区域同步）码扩频.结果表明：比特信噪比Eb/N0为10.5 dB时,遥控误码率为1＆#215;10 6;Eb/N0为9.6 dB时,遥测误码率为1×10^5——与达到相同误码性能的Gold序列相比有1 dB改善,因此,LAS码相比于Gold码能够获得更好的误码性能.     

Satellite inclination effects on UHF Satcom operation

The cause, magnitude, and time variance of satellite inclination are examined in light of the effects on military UHF SATCOM operation. The effects on required demodulator acquisition range, earth coverage footprint, and user terminal antenna pointing accuracy are considered. It is shown that the allowable satellite inclination to maximize on-orbit lifetime is not based on earth-terminal antenna pointing accuracy, but on allowable loss of high-latitude satellite coverage area. Worst-case Doppler shift for a UHF military satellite is 85-Hz uplink and 67-Hz downlink for a 5° SATCOM user elevation angle and 10° of satellite inclination. This amount of inclination is a reasonable allowance for station-keeping, to minimize thruster fuel and thus maximize satellite life. It is also shown that uplink Doppler frequency shift due to satellite inclination may be corrected based on satellite ephemeris data and rough user terminal location data     

C频段统一测控系统非相干测速功能探讨

针对目前国内C频段统一测控系统因不具备测速功能,在发遥控期间无法进行测距,导致其无法对卫星进行连续轨道测量的缺陷,提出了非相干测速方法。非相干测速利用卫星遥测信息中的上行载波多普勒信息以及地面站获取的下行载波多普勒信息,计算得到双向多普勒信息,对双向多普勒进行计算可获得连续的卫星运动速度信息。本文在理论上证明了这种方法的可行性,并以自旋式卫星同步控制过程中天地时延精确修正为例,说明了这种方法的应用价值。     

Single Channel Per Carrier Satellite Repeater Channel Capacity

This paper analyzes the performance of a number of modulation and speech processing techniques that have been considered for single voice channel per carrier transmissions via satellite. This transmission mode is applicable to demand assignment systems, which make possible the most efficient loading of the satellite transponder in applications where the traffic at individual Earth terminals is not sufficient to justify a substantial number of dedicated channels. The analysis basically determines the operating point for the satellite transponder which minimizes the required Earth terminal G/T. The fraction of the total link noise allocated to uplink noise is treated as a parameter, so that the cost of improving G/T may be traded against the cost of providing increased Earth terminal transmitter power. Both analog and digital modulation techniques are considered, together with various practical combinations of syllabic companding, voice-actuated carriers, and error-correcting codes. The results are presented in general analytic form, applicable to any modulation technique for which carrier-to-noise density ratio, channel width, and guardband width may be specified. Curves showing required G/T as a function of the total number of voice channels per transponder are also presented for the above-mentioned signal processing techniques, assuming "CCIR/CITT type" speech quality and transponder EIRP and bandwidth typical of current domestic satellite configurations.     

平经度与偏心率联合偏置双星共位技术

针对在偏心率隔离情况下,由于共位双星半长轴并不完全相同,导致双星平经度差不断增加的情况,讨论了平经度与偏心率联合偏置情况下的双星共位控制策略.该策略通过计算得到双星允许的最大平经度差,控制双星漂移过程中的平经度差保持在允许的范围,确保在偏心率偏置条件下实现双星的安全隔离.理论和算例表明,双星共位的控制周期与卫星的测控精度有关,随着测控精度的提高,双星共位的控制周期可以等于每颗星的东西位置保持周期.     

测控中的星载计算机快速切换

针对低轨卫星长期管理与测控中的星载计算机所需要的切换、维护的测控时间相对较长的问题,在分析原有主、备星载计算机的时间比对方法的基础上,直接针对备机建立新的时间同步模型,并进行公式推导和理论误差分析;然后建立新的测控事件调度模型,实现时间同步数据与主备机一致性数据的同时注入,优化工作流程,并有效缩短测控时间;最后编写新的遥控作业,在测控中进行实践.应用结果表明,采用新方法可以在一个测控圈次内完成在轨星载计算机的切换与维护,MTTR(Mean Time To Repair,平均恢复时间)小于8 min,时间同步精度优于1 ms,所需测控圈次相对于原方法减少83％以上,适用于在轨卫星长期管理与测控.     

14.5-14.8 GHz Frequency Sharing by Data Relay Satellite Uplinks and Broadcasting-Satellite Uplinks

Data relay satellites are being developed to provide real-time data links between research satellites in low earth orbits and central data acquisition and processing facilities. Frequency assignments for data relay satellite links will be made in bands allocated internationally to the space research service. One of the bands which will be used lies between 14.5 and 15.35 GHz, where the space research service has had a frequency allocation as a secondary service since 1971. During the General World Administrative Radio Conference of the International Telecommunication Union, held in Geneva in 1979, a primary frequency allocation was made in the band 14.5-14.8 GHz to the fixed-satellite service, specifically for use by earth-to-space links of the broadcasting satellite service. The feasibility of shared band operation is evaluated between data relay satellite uplinks and broadcasting-satellite feeder links in the band 14.5-14.8 GHz. Relationships for predicting interference power levels are formulated, as functions of satellite separation and of earth station separation. Tradeoffs between satellite separation angle and earth station separation are explored, and conclusions are drawn regarding the feasibility of band sharing. Co-channel operation is demonstrated to be technically feasible for typical systems, provided appropriate separations are maintained.     

DGPS/IMU integration-based geolocation system: Airborne experimental test results

This paper addresses differential global positioning system (DGPS)/inertial measurement unit (IMU) integration-based geolocation system developed for airborne remote sensing cameras. First, we provide a brief review on sensor calibration, alignment and sensor fusion as background material of this research. After presenting those background material, as a main part of this paper we present a geolocation algorithm designed for an airborne imaging system. The geolocation system developed is tested through actual airborne experiments. For the verification of the geolocation system developed, we compare initial stationary states of the airplane before-taking off with states after-landing. From the actual test results, we find that it is critical to do an accurate time synchronization between IMU, DGPS, and airborne images, and to compensate for the data delay occurred during the network transfer.     

Optimal Terminal Rendezvous as a Stochastic Differential Game Problem

The optimal terminal rendezvous of two satellites in orbit about the Earth is studied using a stochastic model and formulating the rendezvous as a game problem. Each satellite has noise-corrupted output measurements and uses a Kalman filter to generate the best estimate of the states describing the rendezvous. The optimal control for the satellites is determined. A comparison is made in terms of dimensionality and complexity to a deterministic solution of the rendezvous problem.     

Networks of low-Earth orbit store-and-forward satellites

A slotted multiaccess protocol is proposed for networks of low-Earth orbit store-and-forward communications satellites. Networks of this type would provide communication between low cost geographically distributed Earth stations, and would be particularly attractive in areas where conventional terrestrial communications systems were not available. Applications of this type include data acquisition and remote process monitoring. The proposed protocol incorporates time division multiplexing (TDM) on the downlink, slotted Aloha with collision resolution on the uplink, and an automatic repeat request (ARQ) algorithm. Since the network connectivity is intermittent, analysis of networks of this type is difficult. Nevertheless, relationships among the performance parameters for a general network are deduced, and performance of three particular network configurations is studied via simulation     

Urban area performance of GPS receiver with simultrac capability

The theory of operation, practical applications, and technical performance of a Global Positioning System (GPS) receiver designed for urban area use are presented. The receiver tracks as many as eight satellites, or all visible satellites, and uses the signals of the four best satellites to ascertain its location. If visibility of one satellite is blocked, one of the additional satellites can be used to provide continuous navigation. Component-level system design choices are shown to support superior automotive vehicle location performance, including optimum mobile communication with satellites and ground-based relays     

GPS III system operations concepts

Over the past three years, the Lockheed Martin GPS III team has analyzed potential operational concepts for the Air Force. The completed tasks support the government's objective of a "realizable and operationally feasible" US Strategic Command (USSTRATCOM) and Air Force Space Command (AFSPC) concept of operations. This paper provides an overview of the operational improvements for the command and control of satellites, the provision of safe, precise navigation and timing services to end-users. The GPS III system changes existing operational paradigms. Improved operator capabilities are enabled by a new high-speed uplink/downlink and crosslink communication architecture. Continuous connectivity allows operators a "contact one satellite - contact all satellites" concept enabling near-real-time navigation updates and telemetry monitoring. This paper describes potential improvements for the following operations: constellation monitoring, command and control, navigation upload monitoring, global service monitoring, global service prediction, civilian navigation (CNAV) messaging, and anomaly detection and resolution. This paper also describes future operational improvements as GPS applications continue to proliferate and the need for an improved infrastructure to effectively manage all the systems that affect GPS service grows     

Scan-based emitter passive localization

This paper investigates the problem of estimating the position of a scanning emitter using a passive scan-based geolocation technique. This is achieved by taking advantage of the geometric constraints introduced by the uniform rotating motion of the antenna main beam as it sweeps across a number of separate receivers. A detailed analysis of the estimation process and accuracy of the emitter position is given and a number of computer simulations showing the benefits of this geolocation technique are also included     

低轨卫星多普勒频移特性的快速计算

地面站利用低轨卫星进行通信时,地面接收站接收信号存在明显的多普勒频移现象。为描述多普勒频移特性,首先分析卫星轨道偏心率对多普勒特性曲线的影响,分析表明：轨道偏心率越大,地面站接收信号多普勒变化率越大。其次,推导了卫星多普勒频移的计算表达式,并讨论了低轨卫星多普勒频移特性曲线的快速计算。仿真计算结果表明,该算法可以很好地描述任意低轨道卫星多普勒频移特性,并明显缩短了精确算法的计算时间,对于10 000km轨道高度卫星,算法置信度可达99%以上。     

Geostationary Satellite Navigation Systems

The concept of position determination using geostationary satellites as an alternative to the global positioning system (GPS) is studied. The advantage of a geostationary system is that only three, or at most four, satellites are required to cover the continental United States. A total of twelve satellites are sufficient for global coverage (excluding polar regions), or eight if only longitude and latitude, but not altitude, are measured. The system involves the determination of the range to either four geostationary satellites or, if the altitude is not measured, three geostationary satellites. The accuracy of the proposed systems are evaluated to obtain the rms error associated with position determination, and the concept for the implementation of measurements required by the systems is presented. The accuracy of the systems are adequate for civilian use in the continental United States; however, there is a degradation in accuracy as the location of the user approaches the equator.