Ignition enhancement of ethylene/air by NOx addition

Recently, non-equilibrium plasma assisted combustion (PAC) has been found to be promising in reducing the ignition delay time in hypersonic propulsion system. NO x produced by non-equilibrium plasma can react with intermediates during the fuel oxidation process and thereby has influence on the combustion process. In this study, the effects of NO x addition on the ignition process of both the homogeneous ethylene/air mixtures and the non-premixed diffusion layer are examined numerically. The detailed chemistry for ethylene oxidization together with the NO x sub-mechanism is included in the simulation. Reaction path analysis and sensitivity analysis are conducted to give a mechanistic interpretation for the ignition enhancement by NO x addition. It is found that for both the homogenous and non-premixed ignition processes at normal and elevated pressures, NO 2 addition has little influence on the ignition delay time while NO addition can significantly promote the ignition process. The ignition enhancement is found to be caused by the promotion in hydroxyl radical production which quickly oxidizes ethylene. The promotion in hydroxyl radical production by NO addition is achieved in two ways:one is the direct production of OH through the reaction HO2+NO = NO2+OH, and the other is the indirect production of OH through the reactions NO+O2=NO2+O and C2H4+O = C2H3+OH. Moreover, it is found that similar to the homogeneous ignition process, the acceleration of the diffusion layer ignition is also controlled by the reaction HO2+NO = NO2+OH.     

An approach for parameter estimation of combined CPPM and LFM radar signal

In this paper, the problem of parameter estimation of the combined radar signal adopting chaotic pulse position modulation (CPPM) and linear frequency modulation (LFM), which can be widely used in electronic countermeasures, is addressed. An approach is proposed to estimate the initial frequency and chirp rate of the combined signal by exploiting the second-order cyclostationarity of the intra-pulse signal. In addition, under the condition of the equal pulse width, the pulse repetition interval (PRI) of the combined signal is predicted using the low-order Volterra adaptive filter. Simulations demonstrate that the proposed cyclic autocorrelation Hough transform (CHT) algorithm is theoretically tolerant to additive white Gaussian noise. When the value of signal noise to ratio (SNR) is less than 4 dB, it can still estimate the intra-pulse parameters well. When SNR = 3 dB, a good prediction of the PRI sequence can be achieved by the Volterra adaptive filter algorithm, even only 100 training samples.     

SCC investigation of low alloy ultra-high strength steel 30CrMnSiNi2A in 3.5wt%NaCl solution by slow strain rate technique

To evaluate stress corrosion cracking(SCC) mechanism of low alloy ultra-high strength steel 30CrMnSiNi2 A in environment containing NaCl, SCC behavior of the steel in 3.5wt% NaCl solution is investigated by slow strain rate technique(SSRT) with various strain rates and applied potentials, surface analysis technique, and electrochemical measurements. SCC susceptibility of the steel increases rapidly with strain rate decreasing from 1 · 10 5s 1to 5 · 10 7s 1, and becomes stable when strain rate is lower than 5 · 10 7s 1. SCC propagation of the steel in the solution at open circuit potential(OCP) needs sufficient hydrogen which is supplied at a certain strain rate.Fracture surface at OCP has similar characteristics with that at cathodic polarization 1000 mVSCE, which presents characteristic fractography of hydrogen induced cracking(HIC).All of these indicate that SCC behavior of the steel in the solution at OCP is mainly controlled by HIC rather than anodic dissolution(AD).     

Fatigue crack propagation of new aluminum lithium alloy bonded with titanium alloy strap

A new type of aluminum lithium alloy (Al-Li alloy) Al-Li-S-4 was investigated by test in this paper. Alloy plate of 400 mm · 140 mm · 6 mm with single edge notch was made into samples bonded with Ti-6Al-4V alloy (Ti alloy) strap by FM 94 film adhesive after the surface was treated. Fatigue crack growth of samples was investigated under cyclic loading with stress ratio (R) of 0.1 and load amplitude constant. The results show that Al-Li alloy plate bonded with Ti alloy strap could retard fatigue crack propagation. Retardation effect is related with width and thickness of strap. Flaws have an observable effect on crack propagation direction.     

Tangling and instability effect analysis of initial in-plane/out-of-plane angles on electrodynamic tether deployment under gravity gradient

The space debris occupies the orbit resources greatly, which seriously threats the safety of spacecraft for its high risks of collisions. Many theories about space debris removal have been put forward in recent years. The Electro Dynamic Tether (EDT), which can be deployed under gravity gradient, is considered to be an effective method to remove debris in low orbit for its low power consumption. However, in order to generate sufficient Lorentz force, the EDT needs to be deployed to several kilometers, which increases the risks of tangling and the instability of the EDT system. In the deployment process, different initial in-plane/out-of-plane angles, caused by direction error at initial release or the initial selection of ejection, affect the motion of EDT system seriously. In order to solve these problems, firstly, this paper establishes the dynamic model of the EDT system. Then, based on the model, safety metrics of avoiding tangling and assessing system stability during EDT deployment stage are designed to quantitatively evaluate the EDT system security. Finally, several numerical simulations are established to determine the safety ranges of the initial in-plane/out-of-plane angles on the EDT deployment.     

Radical recombination in a hydrocarbon-fueled scramjet nozzle

To reveal the radical recombination process in the scramjet nozzle flow and study the effects of various factors of the recombination, weighted essentially non-oscillatory(WENO)schemes are applied to solve the decoupled two-dimensional Euler equations with chemical reactions to simulate the hydrocarbon-fueled scramjet nozzle flow. The accuracy of the numerical method is verified with the measurements obtained by a shock tunnel experiment. The overall model length is nearly 0.5 m, with inlet static temperatures ranging from 2000 K to 3000 K, inlet static pressures ranging from 75 k Pa to 175 k Pa, and inlet Mach numbers of 2.0 ± 0.4 are involved.The fraction Damkohler number is defined as functions of static temperature and pressure to analyze the radical recombination progresses. Preliminary results indicate that the energy releasing process depends on different chemical reaction processes and species group contributions. In hydrocarbon-fueled scramjet nozzle flow, reactions with H have the greatest contribution during the chemical equilibrium shift. The contrast and analysis of the simulation results show that the radical recombination processes influenced by inflow conditions and nozzle scales are consistent with Damkohler numbers and potential dissociation energy release. The increase of inlet static temperature improves both of them, thus making the chemical non-equilibrium effects on the nozzle performance more significant. While the increase of inlet static pressure improves the former one and reduces the latter, it exerts little influence on the chemical non-equilibrium effects.     

Matching suitable feature construction for SAR images based on evolutionary synthesis strategy

In the paper,a set of algorithms to construct synthetic aperture radar（SAR）matching suitable features are frstly proposed based on the evolutionary synthesis strategy.During the process,on the one hand,the indexes of primary matching suitable features（PMSFs）are designed based on the characteristics of image texture,SAR imaging and SAR matching algorithm,which is a process involving expertise;on the other hand,by designing a synthesized operation expression tree based on PMSFs,a much more flexible expression form of synthesized features is built,which greatly expands the construction space.Then,the genetic algorithm-based optimized searching process is employed to search the synthesized matching suitable feature（SMSF）with the highest effciency,largely improving the optimized searching effciency.In addition,the experimental results of the airborne synthetic aperture radar ortho-images of C-band and P-band show that the SMSFs gained via the algorithms can reflect the matching suitability of SAR images accurately and the matching probabilities of selected matching suitable areas of ortho-images could reach 99±0.5%.     

我国空间站运行的测控通信工作模式初探

在分析我国载人空间站在轨运行的任务特点和对测控通信提出的新要求的基础上,对测控通信工作模式进行了探讨。针对任务中心,采用分布式模式进行任务的组织和实施,建立常态化工作体系;针对测控通信资源的使用,对资源进行简化、优化,发挥天、地基各自优势,并实现天地基资源统一调度;针对在轨故障诊断和应急处置,提出了“天地联合,以地为主”的载人航天故障诊断模式和实现途径;针对空间站遥操作需求,提出了一套工作模式和实施流程;针对测控通信长期执行任务的可靠性,提出了任务中心容灾备份工作模式和通信路由的备份模式。以期为后续任务工作模式设计提供参考。     

Temperature effect on buckling properties of ultra-thin-walled lenticular collapsible composite tube subjected to axial compression

This paper seeks to outline the temperature effect on the buckling properties of ultra-thin-walled lenticular collapsible composite tube(LCCT) subjected to axial compression.The buckling tests of the LCCT specimens subjected to axial compression were carried out on INSTRON-500 N servo-hydraulic machine in dry state and at the temperatures of 25 C, 100 C and 80 C. The load–displacement curves and buckling initiation loads were measured and the buckling initiation mechanism was discussed from experimental observations. Experiments show that the buckling initiation load, on average, is only about 2.2% greater at the low temperature of 80 C than at the room temperature of 25 C due to the material hardening, demonstrating an insignificant increase in the buckling initiation load, whereas it is about 19.5% lower at the high temperature of 100 C than at the room temperature owing to the material softening, implying a significant decrease in the buckling initiation load. The failure mode of the LCCT in axial compression tests at three different temperatures can be reckoned to be characteristic of the buckling initiation and propagation around the central region until rupture. The finite element(FE) model is presented to simulate the buckling initiation mechanism based on the eigenvalue-based methodology. Good correlation between experimental and numerical results is achieved.     

具有时延的漂浮基空间机器人基于泰勒级数预测、逼近的改进非线性反馈控制

 探讨了本体位置与姿态均不受控的漂浮基空间机器人在时间延迟(简称时延)情况下惯性空间轨迹跟踪的控制问题.利用拉格朗日方法并结合系统动量守恒关系,分析、建立了漂浮基空间机器人完全能控形式的系统动力学模型及运动Jacobi关系.以此为基础,针对系统存在时延的情况,利用泰勒级数预测、逼近的方法,建立了适用于时延情况下控制系统设计的数学模型.利用该模型,提出了一种空间机器人在时延情况下的改进非线性反馈控制方案.然后运用Lyapunov第二类方法,结合范数以及图形分析的方法证明了在时延情况下整个闭环控制系统的渐近稳定性.文中提到的控制方案能够有效地克服系统存在时延的影响,控制漂浮基空间机器人末端爪手跟踪惯性空间的期望轨迹.系统数值仿真结果证明了上述控制方案的有效性与精确性.     

Progress in helicopter infrared signature suppression

Due to their low-attitude and relatively low-speed fight profiles, helicopters are subjected to serious threats from radio, infrared(IR), visual, and aural detection and tracking. Among these threats, infrared detection and tracking are regarded as more crucial for the survivability of helicopters. In order to meet the requirements of infrared stealth, several different types of infrared suppressor(IRS) for helicopters have been developed. This paper reviews contemporary developments in this discipline, with particular emphasis on infrared signature suppression, advances in mixer-ejectors and prediction for helicopters. In addition, several remaining challenges, such as advanced IRS, emissivity optimization technique, helicopter infrared characterization, etc., are proposed, as an initial guide and stimulation for future research. In the future, the comprehensive infrared suppression in the 3–5 lm and 8–14 lm bands will doubtfully become the emphasis of helicopter stealth. Multidisciplinary optimization of a complete infrared suppression system deserves further investigation.     

一种基于一致性理论的卫星协同自主探测方法

为了提高天基空间碎片探测系统对空间碎片探测能力,研究了一种基于一致性理论的卫星协同自主探测方法,对系统中的卫星进行协同控制,从而实现对空间碎片进行最长时间的持续跟踪探测。探测星座利用招投标机制选取探测效果最好的卫星,空间碎片周围的卫星载荷再利用一致性理论,协同自主地指向空间碎片,以实现探测星座对空间碎片连续跟踪。仿真结果说明了该方法的有效性,1d内探测星座对典型空间碎片的最大连续观测时间由协同前的 6 min提高到了协同后的 39 min,提高了约 5倍,总观测时间由协同前的 1.5 h提高到 13 h,提高了约 8倍。该方法提高了观测效能,可为天基空间碎片探测系统提供一种对空间碎片协同探测的技术途径。     

Feasibility study of autonomous orbit determination using only the crosslink range measurement for a combined navigation constellation

In order to expand the coverage area of satellite navigation systems, a combined navigation constellation which is formed by a global navigation constellation and a Lagrangian navigation constellation was studied. Only the crosslink range measurement was used to achieve long-term precise autonomous orbit determination for the combined navigation constellation, and the measurement model was derived. Simulations of 180 days based on the international global navigation satellite system(GNSS) service(IGS) ephemeris showed that the mentioned autonomous orbit determination method worked well in the Earth–Moon system. Statistical results were used to analyze the accuracy of autonomous orbit determination under the influences of different Lagrangian satellite constellations.     

Springback prediction of thick-walled high-strength titanium tube bending

Significant springback occurs after tube rotary-draw-bending （RDB）, especially for a high-strength Ti-3A1-2.5V tube （HSTT） due to its high ratio of yield strength to Young＇s modulus. The combination scheme of explicit and implicit is preferred to predict the springback. This simulation strategy includes several numerical parameters, such as element type, number of elements through thickness （NEL）, element size, etc. However, the influences of these parameters on spring- back prediction accuracy are not fully understood. Thus, taking the geometrical specification 9.525 mm × 0.508 mm ofa HSTT as the objective, the effects of numerical parameters on prediction accuracy and computation efficiency of springback simulation of HSTT RDB are investigated. The simulated springback results are compared with experimental ones. The main results are： （1） solid and continuum-shell elements predict the experimental results well; （2） for C3DSR elements, NEL of at least 3 is required to obtain reliable results and a relative error of 29% can occur as NEL is varied in the range of 1-3; （3） specifying damping factor typically works well in Abaqus/Emplicit simulation of springback and the springback results are sensitive to the magnitude of damping factor. In addition, the explanations of the effect rules are given and a guideline is added.     

氟化氢激光烧蚀铝靶冲量耦合系数实验

为了研究激光功率密度对氟化氢激光与铝靶相互作用过程中冲量耦合系数的影响,分别在大气和真空中,用聚焦后的激光烧蚀铝靶,通过改变聚焦到铝靶的光斑大小,得到冲量耦合系数和激光功率密度的关系,并将该实验结果与CO2激光和铝靶相互作用的实验结果进行比较。结果表明,氟化氢激光与铝靶相互作用得到的冲量耦合系数和激光功率密度的关系与CO2激光不同。大气和真空中,氟化氢激光与铝靶相互作用开始出现冲量传递的阈值分别约为8.03×106W/cm2和7.69×106W/cm2,并且这两种情况下,氟化氢激光器与铝靶相互作用得到的最大冲量耦合系数均高于CO2激光。     

Robust trajectory planning for UAV communication systems in the presence of jammers

Unmanned Aerial Vehicle (UAV) has emerged as a promising novel application for the Sixth-Generation (6G) wireless communication by leveraging more favorable Line-of-Sight (LoS) propagation. However, the jamming resistance by exploiting UAV’s mobility is a new challenge in the UAV-ground communication. This paper investigates the trajectory planning problem in an UAV communication system, where the UAV is operated by a Ground Control Unit (GCU) to perform certain tasks in the presence of multiple jammers with imperfect power and location information. To ensure the reliability of the GCU-to-UAV link, we formulate the problem as a non-convex semi-infinite optimization, aiming to maximize the average worst-case Signal-to-Interference-plus-Noise Ratio (SINR) over a given flight duration by designing the robust trajectory of the UAV under stringent energy availability constraints. To handle this problem efficiently, we develop an iterative algorithm for the solution with the aid of S-procedure and Successive Convex Approximation (SCA) method. Numerous results demonstrate the efficacy of our proposed algorithm and offer some useful design insights to practical system.     

地基激光器发射微卫星的方案设计与弹道优化计算

1引言随着高功率激光技术的发展,用地基激光器发射近地轨道卫星将成为可能。上世纪90年代初Hum-bleW E和Pierson B L提出用一台地基300 MW的CO2激光器把初始质量为1 900 kg的飞行器发射到近地轨道[1]。飞行器的弹道在初始段有一向后运动的“后摆”段。这种弹道可以充分利用激光     

Integration of GPS and low cost INS for pedestrian navigation aided by building layout

In outdoor environments, GPS is often used for pedestrian navigation by utilizing its signals for position computation, but in indoor or semi-obstructed environments, GPS signals are often unavailable. Therefore, pedestrian navigation for these environments should be realized by the integration of GPS and inertial navigation system （INS）. However, the lowcost INS could induce errors that may result in a large position drift. The problem can be minimized by mounting the sensors on the pedestrian＇s foot, using zero velocity update （ZUPT） method with the standard navigation algorithm to restrict the error growth. However, heading drift still remains despite using ZUPT measurements since the heading error is unobservable. Also, tbot mounted INS suffers from the initialization ambiguity of position and heading from GPS. In this paper, a novel algorithm is developed to mitigate the heading drift problem when using ZUPT. The method uses building lay- out to aid the heading measurement in Kalman filter, and it could also be combined for the initial- ization. The algorithm has been investigated with real field trials using the low cost Microstrain 3DM-GX3-25 inertial sensor, a Leica GS10 GPS receiver and a uBlox EVK-6T GPS receiver. It could be concluded that the proposed method offers a significant improvement in position accuracy for the long period, allowing pedestrian navigation for nearly40 min with mean position error less than 2.8 m. This method also has a considerable effect on the accuracy of the initialization.     

Experimental investigations on the power extraction of a turbine driven by a pulse detonation combustor

In order to grasp the interaction mechanism between the pulse detonation combustor（PDC）and the turbine,the experimental work in this paper investigates the key factors on the power extraction of a turbocharger turbine driven by a PDC.A PDC consisting of an unvalved tube is integrated with a turbocharger turbine which has a nominal mass flow rate of 0.6 kg/s and50000 r/min.The PDC-turbine hybrid engine is operated on gasoline-air mixtures and runs for6＋min to achieve a thermal steady state,and then the engine performance is evaluated under different operating conditions.Results show that the momentum difference per unit area between the turbine inlet and outlet plays an important role in the power extraction,while the pressure peak of the detonation has little effect.The equivalence ratio of fuel and air mixture and the transition structure between PDC and turbine are also important to the power extraction of the turbine.The present work is promising as it suggests that the performance beneft of a PDC-turbine hybrid engine can be realized by increasing the momentum difference per unit area through the optimal design of transition section between the PDC and turbine.     

Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.