共查询到20条相似文献,搜索用时 140 毫秒
1.
为解决航空发动机套齿动态装配间隙的响应问题,在考虑动态变形和参数不确定性的情况下,将1种非概率区间分析方法与Kriging响应面模型及响应面优化方法相结合,对套齿初始装配间隙进行了可靠性优化设计。以某刚性套齿联轴器作为数值算例,在确定性设计的基础上,考虑机械载荷、热载荷、材料参数的分散性,运用区间分析方法得到了动态装配间隙的响应范围,利用非概率可靠性指标对初始装配间隙进行了优化设计。与确定性设计相比,优化设计提高了结构的可靠性;与概率设计相比,优化设计降低了对不确定参数的信息要求。验证了非概率方法解决装配对象不确定性结构响应问题的可行性与适用性。 相似文献
2.
航空发动机结构可靠性优化方法研究 总被引:1,自引:0,他引:1
通过采用多项式响应面的近似模型和模拟退火寻优技术.建立了航空发动机结构可靠性优化方法:采用多项式响应面为近似模型构造状态变量和目标函数与设计变量的关系,并采用模拟退火算法对响应面模型进行寻优,通过替代距离目标最远点,重构响应面进行模拟退火寻优。涡轮盘结构可靠性优化分析算例结果表明,涡轮盘结构在满足强度和寿命可靠性约束前... 相似文献
3.
采用不同的数学工具描述设计变量不确定性时形成了现有的三种结构可靠性分析方法,分别为概率方法、非概率方法以及混合方法。单一的概率可靠性模型发展已经比较成熟,单一的非概率可靠性模型也有不少学者研究。然而尚没有建立包含概率、模糊、非概率的统一混合可靠性模型。本文先把模糊变量隶属函数转化为具有概率密度函数性质的函数,并结合区间可靠性度量获得统一混合可靠性模型。分析结果表明本文提出的混合可靠性模型计算方法可以有效的处理设计变量的不同客观事实。 相似文献
4.
为实现航空发动机总体性能设计方法由传统的确定性设计向不确定性概率设计转变,提出基于分布式协同响应面法思想的航空发动机多工况性能可靠性循环优化设计方法:建立了引入非确定性部件性能的航空发动机性能仿真模型,通过试验设计、非设计点性能仿真试验等步骤,构建了各典型工况下发动机推力与耗油率性能可靠度关于设计点循环参数的分布式响应面模型,并以此构建多工况性能协同响应面模型进行循环参数优化设计,最终获得循环参数非劣解集并通过随机试验进行验证。结果表明,通过多工况性能可靠性循环优化设计方法获得的循环参数非劣解集均能使发动机在多个典型工况下的总体性能同时达到不低于97.5%的高可靠度,为设计人员根据实际情况选取循环参数提供依据。 相似文献
5.
6.
7.
为了清晰地反映涡轮叶片的疲劳-蠕变交互作用,提高寿命预测结果的准确性及可靠性,并改善涡轮叶片疲劳寿命对随机变量的敏感程度,分别采用Manson-Coffin公式和Larson-Miller方程计算了涡轮叶片的低循环疲劳寿命和蠕变持久寿命,利用修正的时间-寿命分数法计算了涡轮叶片疲劳-蠕变损伤,在此基础上,将响应面法(RSM)与果蝇优化算法(FFOA)相结合,考虑载荷、材料参数、疲劳-蠕变交互程度的不确定性,对涡轮叶片疲劳寿命进行了稳健性优化设计。优化结果表明:涡轮叶片疲劳-蠕变小时寿命的概率区间减小了8.48%,验证了该优化方法的工程可行性。 相似文献
8.
双辐板涡轮盘/榫结构优化设计方法 总被引:4,自引:2,他引:2
提出双辐板涡轮盘/榫三维结构优化设计方法,包括:以盘/榫总质量作为目标函数,分部管理的设计参数,盘/榫结构分部快速优化/整体精细优化策略;基于ANSYS软件,建立了双辐板涡轮盘/榫结构优化设计平台.针对某高压涡轮转子,设计了两种双辐板涡轮盘/榫模型,分析了盘缘喉部半径、盘缘厚度参数对盘/榫危险区应力的影响.优化结果表明:双辐板涡轮盘比单辐板涡轮盘应力分布更加均匀;在满足结构强度约束条件下,两种双辐板涡轮盘分别比单辐板涡轮盘减质19.90%和17.35%;对双辐板涡轮盘/榫模型进行优化,采用该优化设计方法的计算时间仅为采用常规三维优化方法的1/3,表明其优化设计方法的合理性及高效性. 相似文献
9.
涡轮盘结构概率设计体系的研究 总被引:3,自引:0,他引:3
基于涡轮盘结构确定性设计流程,将概率设计理念融入设计过程中,发展了涡轮盘结构的概率设计流程,初步建立了涡轮盘结构的概率设计体系。以涡轮盘结构的传统设计流程为基础,提出涡轮盘结构的概率设计准则,并建立了涡轮盘的概率设计流程。以某型航空发动机涡轮盘低循环疲劳失效为例,按照文中建立的概率设计流程,将形状优化设计结果作为初始结构方案完成了涡轮盘的低循环疲劳概率设计。通过与原设计结果对比表明,按照概率设计观点进行涡轮盘的结构设计能够兼顾结构静强度性能和结构强度可靠性,在满足可靠度的前提下降低涡轮盘的质量,有效地提高其设计质量,初步验证了涡轮盘概率设计流程的有效性和可行性。 相似文献
10.
11.
12.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
13.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
14.
15.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
16.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
17.
18.
19.
航天器返回地球的气动特性综述 总被引:4,自引:0,他引:4
航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。 相似文献
20.
FU Hong-jun MA Chong-qi KUANG Nai-hang LUAN Shi-lin 《中国航空学报》2007,20(2):124-128
This work was dedicated to performing surface oxidation and coating treatments on carbon fibers (CF) and investigating the changes of fiber surface properties after these treatments, including surface composition, relative volume of functional groups, and sur- face topography with X-ray photoelectron spectroscopy (XPS) and atom force microscopy (AFM) technology. The results show that, after oxidation treatments, interfacial properties between CF and non-polar polyarylacetylene (PAA) resin are remarkably modified by removing weak surface layers and increasing fiber surface roughness. Coating treatment by high char phenolic resin solution after oxida- tion makes interface of CF/PAA composites to be upgraded and the interfacial properties further bettered. 相似文献