Harmonic analysis of a parallel-loaded resonant converter

A method for calculating the harmonic components of the currents and voltages in a parallel-loaded resonant converter using frequency-domain techniques is presented. The converter is divided into an inverter section and a rectifier section. A harmonic model is developed for the resonant converter in which the rectifier section is treated as a voltage-dependent current sink. All voltages and currents in this model are represented by a Fourier series. The unknown coefficients in all Fourier series are calculated by using the harmonic model and Kirchhoff's laws. Because of the nonlinear nature of the rectifier section, an iterative technique must be utilized to find the unknown Fourier coefficients     

Small-Signal Model for the Series Resonant Converter

The results of a previous discrete-time model of the series resonant dc-dc converter are reviewed and from these a small signal dynamic model is derived. This model is valid for low frequencies and is based on the modulation of the diode conduction angle for control. The basic converter is modeled separately from its output filter to facilitate the use of these results for design purposes. Experimental results are presented.     

Steady-state analysis of the constant-frequency clamped seriesresonant converter

A constant-frequency diode-clamped series resonant converter (CFCSRC) is proposed as a solution to problems associated with frequency-controlled resonant converters. This converter has two resonant frequencies, and control is achieved by varying the relative time spent at each switching frequency. Two zero-current-switching (ZCS) modes are examined and plotted in the output plane. An equation is given for the boundary between the two ZCS modes, as well as an expression for the boundary between ZCS and non-ZCS operation; both are plotted in the output plane. The output equation for the main mode is shown to be hyperbolic. Converter peak voltages limited to the input voltages, and peak currents are less than those of the frequency-controlled clamped series resonant converter over a large operating range. Data from a prototype converter are compared with theoretical data and are shown to be in good agreement with the theoretical model     

Generalized approach to the small signal modelling of DC-to-DCresonant converters

A generalized small-signal analysis approach that is based on both the Taylor's series expansion and the state-plane diagram is presented. A generalized discrete small-signal model for a double-ended DC-to-DC resonant converter operating in the continuous conduction mode is also given. Based on the model derived, the frequency responses for two transfer functions, namely, the line-to-output and the control-to-output transfer functions, are obtained. The technique is verified by applying it to the conventional series resonant converter whose small-signal analysis is known     

Analysis of series-parallel resonant converter

A frequency-domain steady-state analysis is given for a series-parallel resonant converter (SPRC) operating in the continuous conduction mode (CCM) using Fourier series techniques. Equations for performance parameters are derived under steady-state conditions to provide simple design tools. The topology of the SPRC combines the advantageous properties of both the series resonant converter (SRC) and the parallel resonant converter (PRC). The key results of the work are: a novel half-wave rectifier SPRC, conditions for obtaining high part-load efficiency; and several boundary frequencies and limiting conditions such as the capacitive/inductive load boundary and open-circuit and short-circuit cases. Experimental results measured for an 80-W converter above the resonance at different load resistances and input voltages show excellent agreement with the theoretical performance predicted by the equations     

串联输出DC／DC谐振变换器的稳态分析

分析了高于谐振频率工作的串联输出谐振变换器的工作模式,采用状态变量法计算获得了若干描述稳态工作的特性曲线,为分析和设计这种变换器提供了基础     

Small signal analysis of the LCC-type parallel resonant converter

In this paper, the small signal analysis of the LCC-type parallel resonant converter (LCC-PRC) operating in the continuous conduction mode is given. This analysis is based on both the state-plane diagram, which has been successfully used to obtain the steady state response for resonant converters, and the Taylor series expansion. Applying perturbation directly to the steady state trajectory, a discrete small signal model for the converter can be derived in terns of the input voltage, switching frequency, and the converter state variables. Based on this analysis, closed-loop form solutions for the input-to-output and control-to-output transfer functions are derived. It is shown that the theoretical and computer simulation results are in full agreement     

Effect of FET output capacitance on ZVS of resonant converters

The analysis of resonant converters including the capacitance of the switches is presented. New dc characteristics are obtained for the series, parallel, and series-parallel resonant converters (SPRC). The operating regions where the converters operate with zero-voltage switching (ZVS) are determined as a function of the switch capacitance. The more pronounced effect can be seen in the series resonant converter (SRC), while the parallel resonant converter (PRC) is the most insensitive. The results of the analysis have been verified on an experimental prototype     

Analysis and design of (LC)(LC)-type series-parallel resonantconverter

A series-parallel resonant converter employing (LC)(LC)-type tank circuit operating in lagging power factor (PF) mode is presented and analyzed using complex ac circuit analysis. Design curves are obtained and the converter is optimized under certain constraints. Detailed Space Integrated Control Experiment (SPICE) simulation results are presented to evaluate the performance of the designed converter under varying load conditions. Results obtained from an experimental converter are also presented. The results obtained from the theory, SPICE simulation, and the experimental converter are compared. The proposed converter has high efficiency from full load to very light load (<10%). Switching frequency variation required for a wide change in the load (near load open circuit to full load) is narrow compared with the series resonant converter (SRC)     

Robust controller design for a series resonant converter

Because of their reduced switching losses, allowing a higher operating frequency, dc-to-dc resonant converters have been used extensively in the design of smaller size and lighter weight power supplies. The steady state and dynamic behavior of both the conventional series and parallel resonant converters have been thoroughly analyzed and small-signal models around given nominal operating points have been obtained. These models have been used in the past to design controllers that attempted to keep the output voltage constant in the presence of input perturbations. However, these controllers did not take into account either load or components variations, and this could lead to instability in the face of component or load changes. Moreover, prediction of the frequency range for stability was done a posteriori, either experimentally or by a trial and error approach In this paper we use μ-synthesis to design a robust controller for a series resonant converter (SRC). In addition to robust stability the design objectives include rejection of disturbances at the converter input while keeping the control input and the settling time within values compatible with a practical implementation     

Three-phase single-stage ac/dc boost integrated series resonant converter

A new ac/dc 3-/spl phi/ single-stage converter is proposed integrating a 3-/spl phi/ discontinuous current mode (DCM) boost with a dc/dc fixed frequency series resonant converter (SRC). This converter has the following features: natural power factor correction, soft switching, high-frequency (HF) transformer isolation with the series resonant tank operating in above resonance mode, etc. A new complementary gating control scheme is used for simultaneous control of boost converter and the SRC. Modes of operation are presented and analyzed. Based on the analysis, design curves are obtained. An optimum design is given and a design example is presented. Results obtained from SPICE simulation for the designed converter are given to verify the performance of the proposed converter for varying load as well as line voltage. Experimental results obtained from a laboratory prototype converter are presented to verify the theory.     

Analysis and Design of Series Resonant Converter by State-Plane Diagram

Analysis based on the state-plane diagram is given for series resonant converters operating in the frequency range 0.5 ? fs/fo ? 1.0. When the voltages and currents in the converter are normalized, design parameters take on special geometric meanings in the normalized state diagram. Examples of converter design using graphical methods are given for the cases of ? and ? control. Control characteristics of the converter operating in the continuous conduction mode are derived. The concept of the energy reflection coefficient is introduced as a measure of power transfer efficiency in the converter design.     

A New Resonant Mode Amplifier Produces Clean AC Power

A new resonant mode power amplifier design is described which has a number of advantages over the power amplifiers available today. In particular, it has low or no EMI because of the nature of its operation. The new amplifier design is based upon a resonant mode dc-dc converter used in a push-pull configuration. All the advantages of the resonant mode power converters, such as high efficiency, small size and weight, excellent dynamic performance, low or no EMI (compared to PWM switch mode power converter), etc., are present in this new design.     

A fixed frequency LCL-Type series resonant converter

A fixed frequency LCL-type series resonant converter (SRC) which uses an inductive output filter is proposed. Steady-state analysis of the converter is presented using complex ac circuit analysis. Based on the analysis, a simple design procedure is given. Detailed space integrated control experiment (SPICE) simulation results are presented to evaluate the performance of the designed converter under varying load and supply voltage conditions. Also, detailed experimental results obtained from a metal-oxide-semiconductor field-effect transistor (MOSFET) based 500 W converter are presented to verify the analysis and SPICE simulation results. The results obtained from the analysis, SPICE simulation and the experimental converter are compared. The proposed converter requires a narrow variation in pulsewidth while maintaining lagging power factor mode of operation for a very wide variation in the load as well as supply voltage     

Resonant power supplies: their history and status

The various types of converter are described, and the history of resonant power supplies is briefly sketched. The differences between pulse-width-modulated (PWM) switch mode power supplies and resonant power supplies are discussed. Single-switch, multiple-switch, and series and parallel resonant converters are examined. The control of resonant converters is addressed. Hardware is briefly considered     

A Normalized Model for the Half-Bridge Series Resonant Converter

Closed-form steady-state equations are derived for the halfbridge series resonant converter with a rectified (dc) load. Normalized curves for various currents and voltages are then plotted as a function of the circuit parameters. Experimental results based on a 10-kHz converter are presented for comparison with the calculations.     

Inherent Overload Protection for the Series Resonant Converter

The overload characteristics of the full bridge series resonant power converter are considered. This includes analyses of the two most common control methods presently in use. The first of these uses a current zero crossing detector to synchronize the control signals and is referred to as the ? controller. The second is driven by a voltage controlled oscillator and is referred to as the ? controller. It is shown that the ? controller has certain reliability advantages in that it can be designed with inherent short circuit protection. Experimental results are included for an 86 kHz converter using power metal-oxide-semiconductor field-effect transistors (MOSFETs).     

Steady-State Analysis of the Series Resonant Converter

The series resonant converter is analyzed in steady state, and for constant switching frequency the output current and voltage characteristics are found to be ellipses. The converter operating point can then be easily obtained by superimposing a load line on these elliptical characteristics. Peak resonant capacitor voltage and inductor current are also plotted in the output plane and are dependent to first order only on output current. When peak voltage and current are plotted in this manner, the dependence of component stresses on operating point is clearly revealed. The output characteristics are modified to include the effect of transistor and diode voltage drops, and experimental verification is presented.     

LLC parallel resonant converter design by scaling the LC converter

An efficient and practical method for steady-state design of an LLC-type parallel resonant dc/dc converter (LLC-PRC) is presented. In general, the output characteristic curves of LLC-PRC can be obtained by multiplying the output curves of the LC-type parallel resonant converter (LC-PRC) by a ratio of the parallel and series inductances. The peak voltage and current stresses on the resonant elements also depend on the same ratio. The LLC-PRC with a filter inductor is examined for two conduction modes, continuous and discontinuous capacitor voltage conduction modes, to show the effect of the inductance ratio. A means to use the derived equations to obtain the zero current switching (ZCS) is given. Also, a design procedure, along with design examples, is given to illustrate the use of the equations and characteristic curves. An experimental LLC-PRC is built to ensure the validity of the equations and design examples     

Multimodule parallel series-loaded resonant converters

The design and implementation of a multimodule parallel series-loaded resonant (SLR) converter system is presented. The SLR converter to be paralleled is operated in the n=2 discontinuous mode (DCM). Its dc analysis and dynamic modeling are made. In parallel operation, an average control technique is proposed to compensate the mismatch in current control characteristics of each parallel converter. Good dynamic and static current sharing characteristics are obtained. In addition, to obtain good output voltage regulating control performance, a design procedure is presented to find the parameters of feedback voltage controller according to the prescribed specifications