共查询到20条相似文献,搜索用时 46 毫秒
1.
利用~1H-NMR法对不同催化剂制得的Resole型酚醛树脂及有关模型化合物的结构进行了研究。实验结果表明,树脂中邻-酚醇(或称羟甲基)与对-酚醇之比(O/P)与所使用的催化剂类型、用量、苯酚/甲醛(P/F)摩尔比以及反应条件有关。由二步法合成(即先在酸性催化剂作用下合成Novolac型酚醛树脂,然后又在碱性催化剂作用下与甲醛进一步反应)的Resole型酚醛树脂的主要结构是各种取代的亚甲基桥(—CH_2—)。 相似文献
2.
采用热重分析法和热重质谱联用技术考察了氨酚醛树脂的热解反应行为,以Coats-Redfern积分法对实验数据进行动力学解析,得到了氨酚醛树脂热解反应的动力学参数。结果表明,氨酚醛树脂的热解反应分为两种:在600℃以下的低温区,以链断裂反应为主;在600~800℃的高温区,以脱氢反应为主。氨酚醛树脂热解反应可以用两个分段一级动力学方程来描述,升温速率对两种热解反应的表观活化能影响都不大。 相似文献
3.
4.
以丁腈橡胶(CTBN)为增韧剂对环氧树脂(F51)进行增韧改性,通过FTIR、TG以及力学性能测试研究了丁腈橡胶对环氧树脂固化反应、热稳定性能和力学性能的影响,并分析了其增韧机理;分别采用燃气流剪切烧蚀试验和电弧风动烧蚀实验考核了低密度烧蚀材料的烧蚀性能。结果表明:经CTBN改性后,两者的分子链产生了一定程度的交联;树脂基体的拉伸、弯曲性能有所下降,但韧性得到了增强;热稳定性大大提高,增韧后的F51树脂在800℃时的残重率由增韧前的23%提高到了54%;低密度烧蚀材料的抗剪切、抗剥蚀能力得到了增强,且碳层的尺寸稳定性也得到了改善,烧蚀性能提高。 相似文献
5.
以硅乙烯基1,7-碳硼烷为B源与含乙烯基硅氮烷反应生成了一种新型的SiBCN杂化树脂。采用FT-IR、DSC、TGA和Py GC-MS对树脂的结构、固化行为、热稳定性、热裂解反应和过程进行了研究,并用Kissinger方程和FWO法计算出了固化反应和热裂解的表观活化能,分析了树脂的裂解过程及机理。结果表明:这种杂化树脂在固化过程中存在一个放热峰,固化表观活化能为113.55 k J/mol,具有较好的热稳定性,N_2气氛下,T_d~5为459℃,900℃下的残碳率为73.1%。随着裂解反应程度的增加,树脂裂解的表观活化能增加,动力学热稳定性增强。当裂解温度为300℃时,树脂主要发生转氨基反应,裂解产生NH_3;500℃时,有机基团脱除,树脂裂解产生NH_3、CH_4和CH_2=CH_2等烯烃;650℃时,裂解气体种类进一步增加,生成一系列烷烃和烯烃。 相似文献
6.
7.
张阳%曾金芳%薛建毅 《宇航材料工艺》2008,38(6)
文摘采用差示扫描量热法和傅里叶红外光谱法研究了镁酚醛树脂的固化反应特性,包括反应动力学和固化反应机理,热失重研究树脂固化后的耐热性能。研究表明:镁酚醛树脂表观活化能约为82.42 kJ/mol,反应级数为0.913,和普通酚醛树脂固化过程相比反应中有新的结构变化,热失重测试结果表明其耐热性能优异、残碳率较高,在以升温速率为10℃/m in条件下升温至800℃时残碳率可达到58.57%。镁酚醛树脂加热可快速固化,最佳固化成型温度控制在150~160℃。 相似文献
8.
9.
10.
利用高邻位酚醛树脂与邻苯二甲腈偶氮盐之间的偶合反应制备了带有邻苯二甲腈基团的新型高邻位酚醛树脂。结构中的腈基在加热条件下可以进行加成固化反应。通过相同方法制备了取代基团含量不同的酚醛树脂并进行了研究。结果表明:最高取代度为89%,随着取代度的增加树脂的分子量呈现出递减的趋势。固化过程中偶氮键在160~230%附近分解,腈基的加成固化出现在260~340%。与传统的酚醛树脂相比,固化后的树脂具有更好的热稳定性和更高的残碳率。 相似文献
11.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
12.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
13.
14.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
15.
16.
航天器返回地球的气动特性综述 总被引:4,自引:0,他引:4
航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。 相似文献
17.
Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis 总被引:2,自引:0,他引:2
GAO Hong-liang ZHANG Hui WANG Shu-juan 《中国航空学报》2007,20(1):75-80
Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved. 相似文献
18.
19.
Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters 总被引:1,自引:0,他引:1
ZHOU Hong-guo WEI Xiu-ying MAO Chang-hui XIONG Yu-hua QIN Guang-rong 《中国航空学报》2007,20(2):172-176
The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃). 相似文献
20.
YANG Fen ZHANG Xue-jun TIAN Fang WU Xu GAN Fu-xing 《中国航空学报》2007,20(2):181-186
Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration. 相似文献