GPS-based sea level measurements to help the characterization of land contamination in coastal areas

The Corsica site has been established in 1996 to perform altimeter calibration on TOPEX/Poseidon and then on its successors Jason-1 and Jason-2. The first chosen location was under the #85 ground track that overflight the Senetosa Cape. In 2005, it was decided to develop another location close to Ajaccio, to be able to perform the calibration of Envisat and in a next future of SARAL/AltiKa that will flight over the same ground tracks. Equipped with various instruments (tide gauges, permanent GPS, GPS buoy, weather station…) the Corsica calibration site is able to quantify the altimeter Sea Surface Height bias but also to give an input on the origin of this bias (range, corrections, orbits, …). Due to the size of Corsica (not a tiny island), the altimeter measurement system (range and corrections) can be contaminated by land. The aim of this paper is to evaluate this land contamination by using GPS measurements from a fixed receiver on land and from another receiver onboard a life buoy. Concerning the altimeter land contamination, we have quantify that this effect can reach 8 mm/km and then affects the Sea Surface Height bias values already published in the framework of the Corsica calibration site by 5–8 mm for TOPEX and Jason missions. On the other hand, the radiometer measurements (wet troposphere correction) are also sensitive to land and we have been able to quantify the level of improvement of a dedicated coastal algorithm that reconciles our results with those coming from other calibration sites. Finally, we have also shown that the standard deviation of the GPS buoy sea level measurements is highly correlated (∼87%) with the Significant Wave Height derived from the altimeters and can be used to validate such parameter.     

Regional in situ validation of satellite altimeters: Calibration and cross-calibration results at the Corsican sites

The in situ validation of the satellite altimeter sea surface heights is generally performed either at a few local points directly flown over by the satellites or using the global tide gauge network. A regional in situ calibration method was developed by NOVELTIS in order to monitor the altimeter data quality in a perimeter of several hundred kilometres around a given in situ calibration site. The primary advantage of this technique is its applicability not only for missions flying over dedicated sites but also for missions on interleaved or non repetitive orbits. This article presents the altimeter bias estimates obtained with this method at the Corsican calibration site, for the Jason-1 mission on its nominal and interleaved orbits as well as for the Jason-2 and Envisat missions. The various regional bias estimates (8.2 cm and 7.4 cm for Jason-1 respectively on the nominal and interleaved orbits in Senetosa, 16.4 cm for Jason-2 in Senetosa and 47.0 cm for Envisat in Ajaccio, with an accuracy between 2.5 cm and 4 cm depending on the mission) are compared with the results obtained by the other in situ calibration teams. This comparison demonstrates the coherency at the centimetre level, the stability and the generic character of the method, which would also be of benefit to the new and future altimeter missions such as Cryosat-2, SARAL/AltiKa, Sentinel-3, Jason-3, Jason-CS.     

Calibration of Envisat radar altimeter over Lake Issykkul

This study presents the results of calibration/validation (C/V) of Envisat satellite radar altimeter over Lake Issykkul located in Kyrgyzstan, which was chosen as a dedicated radar altimetry C/V site in 2004. The objectives are to estimate the absolute altimeter bias of Envisat and its orbit based on cross-over analysis with TOPEX/Poseidon (T/P), Jason-1 and Jason-2 over the ocean. We have used a new method of GPS data processing in a kinematic mode, developed at the Groupe de Recherche de Geodesie Spatiale (GRGS), which allows us to calculate the position of the GPS antenna without needing a GPS reference station. The C/V is conducted using various equipments: a local GPS network, a moving GPS antenna along the satellites tracks over Lake Issykkul, In Situ level gauges and weather stations. The absolute bias obtained for Envisat from field campaigns conducted in 2009 and 2010 is between 62.1 and 63.4 ± 3.7 cm, using the Ice-1 retracking algorithm, and between 46.9 and 51.2 cm with the ocean retracking algorithm. These results differ by about 10 cm from previous studies, principally due to improvement of the C/V procedure. Apart from the new algorithm for GPS data processing and the orbit error reduction, more attention has been paid to the GPS antenna height calculation, and we have reduced the errors induced by seiche over Lake Issykkul. This has been assured using cruise data along the Envisat satellite track at the exact date of the pass of the satellite for the two campaigns. The calculation of the Envisat radar altimeter bias with respect to the GPS levelling is essential to allow the continuity of multi-mission data on the same orbit, with the expected launch of SARAL/Altika mission in 2012. Implications for hydrology in particular, will be to produce long term homogeneous and reliable time series of lake levels worldwide.     

Evaluation of SARAL/AltiKa performance using GNSS/IMU equipped buoy in Sajafi,Imam Hassan and Kangan Ports

Performance of SARAL/AltiKa mission has been evaluated within 2016 altimeter calibration/validation framework in Persian Gulf through three campaigns conducted in the offshore waters of Sajafi, Imam Hassan and Kangan Ports, while the altimeter overflew the passes 470, 111 and 25 on 13 Feb, 7 March and 17 June 2016, respectively. As the preparation, a lightweight buoy was equipped with a GNSS receiver/choke-ring antenna and a MEMS-based IMU to measure independent datasets in the field operations. To obtain accurate sea surface height (SSH) time series, the offset of the onboard antenna from the equilibrium sea level was predetermined through surveying operations as the buoy was deploying in the onshore waters of Kangan Port. Accordingly, the double-difference carrier phase observations have been processed via the Bernese GPS Software v. 5.0 so as to provide the GNSS-derived time series at the comparison points of the calibration campaigns, once the disturbing effects due to the platform tilt and heave have been eliminated. Owing to comparing of the SSH time series and the associating altimetry 1?Hz GDR-T datasets, the calibration/validation of the SARAL/AltiKa has been performed in the both cases of radiometer and ECMWF wet troposphere corrections so as to identify potential land contamination. An agreement of the present findings in comparison with those attained in other international calibrations sites confirms the promising feasibility of Persian Gulf as a new dedicated site for calibration/validation of ongoing and future altimetry missions.     

Ionospheric correction using GPS Klobuchar coefficients with an empirical night-time delay model

We proposed an ionospheric correction approach called NKlob to mitigate the ionospheric delay errors. NKlob is a modification of the original GPS Ionospheric Correction Algorithm (ICA), which uses an empirical night-time model depending on the time, geomagnetic location and periodicities of the ionospheric behavior to replace the night-time constant delay in GPS ICA. Performance of NKlob was evaluated by the independent total electron contents (TECs) derived from Global Ionospheric Maps (GIMs) of the International GNSS Services (IGS) and Jason-2 altimetry satellite during 2013–2017. Compared to GIM TECs, NKlob corrects 51.5% of the ionospheric delay errors, which outperforms GPS ICA by 6.3%. Compared to Jason-2 TECs, NKlob mitigates the ionospheric errors by 58.1%, which is approximately 3.7% better than that of GPS ICA. NKlob shows significant improvement in low-latitude and equatorial regions with respect to GPS ICA, meanwhile exhibiting comparable performance at middle and high latitudes. Since NKlob only requires slight technical changes at the processing level of GPS receivers, we suppose that it can be easily implemented for better ionospheric delay corrections of real-time GPS single-frequency applications.     

DORIS system: The new age

The boarding of the first DGXX DORIS instrument on Jason-2 mission gives us the opportunity to present the improvements that have been implemented on the DORIS system. The goal of this paper is to present information about the new capacities of the DORIS system and to give the current status of its components. An overview of the DORIS system, the International DORIS Service and the Jason-2 satellite mission are first presented. Then the new characteristics of the on-board instrument are detailed. The capacity to track up to seven ground beacons simultaneously dramatically increases the number of measurements performed: a factor of three increase over Jason-1 is observed at the altitude of 1330 km. It also increases the diversity of directions of observation and allows low elevation measurements from 0°. The new phase measurements capability allows now phase processing. The instability of the Jason-1 USOs (Ultra-Stable Oven-controlled quartz oscillator) while crossing the South Atlantic Anomaly has been solved by decreasing the sensitivity to radiation by a factor of 10. New features of the on-board software enhance the coastal and inland water altimetry and increase the robustness of the data. The new software also improves the real time orbit accuracy for operational altimetry. The improvements introduced concurrently on the ground segment have also significantly enhanced capability. The new RINEX exchange formats provide simultaneous phase and pseudo-range measurements. The maintenance of the DORIS Beacons Network and the work done by the DORIS Signal Integrity monitoring team lead to an increased availability of the Network from 75% to 90% and so to a more homogenous orbit coverage.     

Integrating Non-Tidal Sea Level data from altimetry and tide gauges for coastal sea level prediction

The main objective of this paper is to integrate Non-Tidal Sea Level (NSL) from the joint TOPEX, Jason-1 and Jason-2 satellite altimetry with tide gauge data at the west and north coast of the United Kingdom for coastal sea level prediction. The temporal correlation coefficient between altimetric NSLs and tide gauge data reaches a maximum higher than 90% for each gauge. The results show that the multivariate regression approach can efficiently integrate the two types of data in the coastal waters of the area. The Multivariate Regression Model is established by integrating the along-track NSL from the joint TOPEX/Jason-1/Jason-2 altimeters with that from eleven tide gauges. The model results give a maximum hindcast skill of 0.95, which means maximum 95% of NSL variance can be explained by the model. The minimum Root Mean Square Error (RMSe) between altimetric observations and model predictions is 4.99 cm in the area. The validation of the model using Envisat satellite altimetric data gives a maximum temporal correlation coefficient of 0.96 and a minimum RMSe of 4.39 cm between altimetric observations and model predictions, respectively. The model is furthermore used to predict high frequency NSL variation (i.e., every 15 min) during a storm surge event at an independent tide gauge station at the Northeast of the UK (Aberdeen).     

Generating precise and homogeneous orbits for Jason-1 and Jason-2

Driven by the GMES (Global Monitoring for Environment and Security) and GGOS (Global Geodetic Observing System) initiatives the user community has a strong demand for high-quality altimetry products. In order to derive such high-quality altimetry products, precise orbits for the altimetry satellites are a necessity. With the launch of the TOPEX/Poseidon mission in 1992 a still on-going time series of high-accuracy altimetry measurements of ocean topography started, continued by the altimetry missions Jason-1 in 2001 and Jason-2/OSTM in 2008. This paper contributes to the on-going orbit reprocessing carried out by several groups and presents the efforts of the Navigation Support Office at ESA/ESOC using its NAPEOS software for the generation of precise and homogeneous orbits referring to the same reference frame for the altimetry satellites Jason-1 and Jason-2. Data of all three tracking instruments on-board the satellites (beside the altimeter), i.e. GPS, DORIS, and SLR measurements, were used in a combined data analysis. About 7 years of Jason-1 data and more than 1 year of Jason-2 data were processed. Our processing strategy is close to the GDR-C standards. However, we estimated slightly different scaling factors for the solar radiation pressure model of 0.96 and 0.98 for Jason-1 and Jason-2, respectively. We used 30 s sampled GPS data and introduced 30 s satellite clocks stemming from ESOC’s reprocessing of the combined GPS/GLONASS IGS solution. We present the orbit determination results, focusing on the benefits of adding GPS data to the solution. The fully combined solution was found to give the best orbit results. We reach a post-fit RMS of the GPS phase observation residuals of 6 mm for Jason-1 and 7 mm for Jason-2. The DORIS post-fit residuals clearly benefit from using GPS data in addition, as the DORIS data editing improves. The DORIS observation RMS for the fully combined solution is with 3.5 mm and 3.4 mm, respectively, 0.3 mm better than for the DORIS-SLR solution. Our orbit solution agrees well with external solutions from other analysis centers, as CNES, LCA, and JPL. The orbit differences between our fully combined orbits and the CNES GDR-C orbits are of about 0.8 cm for Jason-1 and at 0.9 cm for Jason-2 in the radial direction. In the cross-track component we observe a clear improvement when adding GPS data to the POD process. The 3D-RMS of the orbit differences reveals a good orbit consistency at 2.7 cm and 2.9 cm for Jason-1 and Jason-2. Our resulting orbit series for both Jason satellites refer to the ITRF2005 reference frame and are provided in sp3 file format on our ftp server.     

Radar altimetry measurements over antarctic ice sheet: A focus on antenna polarization and change in backscatter problems

In this paper, we investigate the impact of the error due to the penetration of the altimetric wave within the snowpack. The phenomenon has two different impacts. The first one, due to temporal change in snow characteristics, affects the ice sheet volume trend as derived from altimetric series. The second one, because of both the anisotropy of the ice sheet surface properties and of the linear antenna polarization, introduces a difference in measurements at crossover points. These two phenomena are the cause of what are probably the most critical limitations to the interpretation of long-term altimetric series in term of mass balance and to the comparison between or data fusion of different missions. Moreover, they will lead to the largest error when comparing data from EnviSat with data from CryoSat, because of the different orbits, or with data from AltiKa, because of the different radar frequencies.     

DORIS and GPS monitoring of the Gavdos calibration site in Crete

Due to its specific geographical location as well as its geodetic equipment (DORIS, GNSS, microwave transponder and tide gauges), the Gavdos station in Crete, Greece is one of the very few sites around the world used for satellite altimetry calibration. To investigate the quality of the Gavdos geodetic coordinates and velocities, we analyzed and compared here DORIS and GPS-derived results obtained during several years of observations. The DORIS solution is the latest ignwd11 solution at IGN, expressed in ITRF2008, while the GPS solution was obtained using the GAMIT software package. Current results show that 1–2 mm/yr agreement can be obtained for 3-D velocity, showing a good agreement with current geophysical models. In particular, the agreement obtained for the vertical velocity is around 0.3–0.4 mm/yr, depending on the terrestrial reference frame. As a by-product of these geodetic GPS and DORIS results, Zenith Tropospheric Delays (ZTDs) estimations were also compared in 2010 between these two techniques, and compared to ECMWF values, showing a 6.6 mm agreement in dispersion without any significant difference between GPS and DORIS (with a 97.6% correlation), but with a 13–14 mm agreement in dispersion when comparing to ECMWF model (with only about 90% correlation for both techniques). These tropospheric delay estimations could also provide an external calibration of the tropospheric correction used for the geophysical data of satellite altimetry missions.     

The effect of geocenter motion on Jason-2 orbits and the mean sea level

We compute a series of Jason-2 GPS and SLR/DORIS-based orbits using ITRF2005 and the std0905 standards ( Lemoine et al., 2010). Our GPS and SLR/DORIS orbit data sets span a period of 2 years from cycle 3 (July 2008) to cycle 74 (July 2010). We extract the Jason-2 orbit frame translational parameters per cycle by the means of a Helmert transformation between a set of reference orbits and a set of test orbits. We compare the annual terms of these time-series to the annual terms of two different geocenter motion models where biases and trends have been removed. Subsequently, we include the annual terms of the modeled geocenter motion as a degree-1 loading displacement correction to the GPS and SLR/DORIS tracking network of the POD process. Although the annual geocenter motion correction would reflect a stationary signal in time, under ideal conditions, the whole geocenter motion is a non-stationary process that includes secular trends. Our results suggest that our GSFC Jason-2 GPS-based orbits are closely tied to the center of mass (CM) of the Earth consistent with our current force modeling, whereas GSFC’s SLR/DORIS-based orbits are tied to the origin of ITRF2005, which is the center of figure (CF) for sub-secular scales. We quantify the GPS and SLR/DORIS orbit centering and how this impacts the orbit radial error over the globe, which is assimilated into mean sea level (MSL) error, from the omission of the annual term of the geocenter correction. We find that for the SLR/DORIS std0905 orbits, currently used by the oceanographic community, only the negligence of the annual term of the geocenter motion correction results in a – 4.67 ± 3.40 mm error in the Z-component of the orbit frame which creates 1.06 ± 2.66 mm of systematic error in the MSL estimates, mainly due to the uneven distribution of the oceans between the North and South hemisphere.     

Global monitoring of tropospheric water vapor with GPS radio occultation aboard CHAMP

The global positioning system radio occultation (GPS RO) technique provides a powerful tool for atmospheric sounding which requires no calibration, is not affected by clouds, aerosols or precipitation, and provides an almost uniform global coverage. The paper deals with application of GPS RO measurements from CHAllenging Minisatellite Payload (CHAMP) for the retrieval of tropospheric water vapor profiles. CHAMP RO data are available since 2001 with up to 200 high resolution atmospheric profiles per day. We introduce a new direct method for water vapor retrieval from GPS RO data. Additionally, a 1Dvar algorithm is used for this purpose. The so derived CHAMP water vapor profiles are validated with radiosonde data on a global scale. Here, both methods come to statistically comparable results revealing a negative bias of less than 0.1 g/kg and a standard deviation of less than 1 g/kg specific humidity in the mid troposphere. Potentials of CHAMP RO retrievals for monitoring the mean tropospheric water vapor distribution on a global scale are presented.     

Estimation of differential code biases with Jason-2/3 onboard GPS observations

With the continuous deployment of Low Earth Orbit (LEO) satellites, the estimation of differential code biases (DCBs) based on GNSS observations from LEO has gained increasing attention. Previous studies on LEO-based DCB estimation are usually using the spherical symmetry ionosphere assumption (SSIA), in which a uniform electron density is assumed in a thick shell. In this study, we propose an approach (named the SHLEO method) to simultaneously estimate the satellite and LEO onboard receiver DCBs by modeling the distribution of the global plasmaspheric total electron content (PTEC) above the satellite orbit with a spherical harmonic (SH) function. Compared to the commonly used SSIA method, the SHLEO model improves the GPS satellite DCB estimation accuracy by 13.46% and the stability by 22.34%, respectively. Compared to the GPS satellite DCBs estimated based on the Jason-3-only observations, the accuracy and monthly stability of the satellite DCBs can be improved by 14.42% and 26.8% when both Jason-2 and Jason-3 onboard observations are jointly processed. Compared with the Jason-2 solutions, the GPS satellite DCB estimates based on the fusion of Jason-2 and Jason-3 observations have an improved consistency of better than 18.26% and 9.71% with the products provided by the Center for Orbit Determination in Europe (CODE) and Chinese Academy of Sciences (CAS). Taking the DCB products provided by the German Aerospace Center (DLR) as references, there is no improvement in accuracy of the GPS satellite DCB estimates based on the fusion of Jason-2 and Jason-3 observations than the Jason-2 solutions alone. A periodic variation is found in the time series of both the Jason-3 and Jason-2 onboard receiver DCB estimates. Preliminary analysis of the PTEC distribution based on the estimated SH coefficients are also presented.     

Evaluating the feasibility of GPS measurements of SSH on board a ship along the Portuguese West Coast

Aiming to validate coastal altimetry data, an exploratory experiment was carried out, using a survey ship with onboard GPS and motion compensation systems. The ship navigation plan followed a track as coincident as possible with the passage of two altimetry satellites, Envisat and Jason-1, along the Portuguese coast, in June 2007.     

A regional tropospheric model for airborne GPS applications

A regional tropospheric model can be constructed using surveys from GPS ground networks. Using this model the tropospheric delays of a kinematic station within the region can be interpolated. However, such a model is generally not suitable for an airborne platform high above the ground networks. In this paper, a method of constructing a regional tropospheric model for airborne GPS applications is described. First, the kinematic station in the air is projected onto the ground. Then the tropospheric delays at projected point are interpolated from those of the ground networks. Finally, the tropospheric delays at projected point are extended upward to the airborne platform using pressure and temperature gradients and humidity exponential function. For validation of this method, the data of airborne campaign carried out by BKG in cooperation with GFZ and BGR 2008 in the northern Alps are used. The results show that GPS kinematic positioning precision in height component can be improved using this method.     

Retrieval of the change of precipitable water vapor with zenith tropospheric delay in the Chinese mainland

As a preliminary step for assessing the impact of global positioning system (GPS) refractive delay data in numerical weather prediction (NWP) models, the GPS zenith tropospheric delays (ZTD) are analyzed from 28 permanent GPS sites in the Chinese mainland. The objectives are to estimate the GPS ZTD and their variability in this area. The differences between radiosonde precipitable water vapor (PWV) and GPS PWV have a standard deviation of 4 mm in delay, a bias of 0.24 mm in delay, and a correlation coefficient of 0.94. The correlation between GPS ZTD and radiosonde PWV amounts to 0.89, indicating that the variety of tropospheric zenith delay can reflect the change of precipitable water vapor. The good agreement also guarantees that the information provided by GPS will benefit the NWP models. The time series of GPS ZTD, which were derived continuously from 2002 to 2004, are used to analyze the change of precipitable water vapor in Chinese mainland. It shows that the general trend of GPS ZTD is diminishing from the south-east coastland to the north-west inland, which is in accordance with the distribution of Chinese annual amount of rainfall. The temporal distribution of GPS ZTD in the Chinese mainland is that the GPS ZTD reaches maximum in summer, and it reaches minimum in winter. The long term differences between the observational data sources require further study before GPS derived data become useful for climate studies.     

An improved,near real time water vapor path delay correction of Cryosat-2 sea surface height measurements

This paper presents improvements of a method (Stum et al., 2011) aimed at computing the water vapor path delay correction of altimeter sea surface height, using total precipitable water measurements from scanning microwave radiometers. The main interest of this improved method is for the Cryosat-2 mission over the ocean. Focus is made on the applicability of the method in near real time. An experiment to produce an operational path delay correction for Jason-2 and Cryosat-2 Interim Geophysical Data Records (IGDR) has been set up. Results confirm that the new correction, although less accurate than the one attainable with an embarked radiometer, improves the Cryosat-2 sea surface height accuracy.     

Refinement of global ionospheric coefficients for GNSS applications: Methodology and results

We developed the methodology for the optimal estimation of global ionospheric coefficients of the current Global Navigation Satellite Systems (GNSSs), including the eight- and ten-parameter Klobuchar-like as well as NeQuick models. The ionospheric coefficients of those correction models are calculated from two sets of globally distributed tracking stations of the International GNSS Services (IGS). Performance of the re-estimated Klobuchar-like and NeQuick coefficients are validated during 2002–2014 over the continental and oceanic areas, respectively. Over the continental areas, GPS TECs derived from 40 ground GPS receivers are selected as reference. The eight-, ten-parameter Klobuchar-like and NeQuick models can mitigate the ionospheric delay by 65.8, 67.3 and 75.0%, respectively. Over the global oceans, the independent TECs derived from Jason-1&2 altimeters are used as reference. The re-estimated ionospheric correction models can mitigate 56.1–66.7% of the delay errors. Compared to the original GPS Ionospheric Correction Algorithm (ICA), performance of those eight-, ten-parameter Klobuchar-like and NeQuick models has improved 3.4, 5.9 and 13.4% during the whole test period, respectively. The methodology developed here takes the advantage of high-quality ionospheric TECs derived from the global network of GNSS receivers. The re-estimated ionospheric coefficients can be used as precise ionospheric products to monitor and assess GNSS broadcast ionospheric parameters and to improve the performance of various single-frequency GNSS applications.     

Jason-2 DORIS phase measurement processing

The DORIS instrument on Jason-2 is the first of a new generation. The satellite receivers have now seven simultaneous measurement channels, with synchronous dual frequency phase and pseudo-range measurements. These measurements are now described in a similar manner as GPS measurements and an extension of the RINEX 3.0 format has been defined for DORIS. Data are available to users with a shorter latency.