共查询到20条相似文献,搜索用时 62 毫秒
1.
发动机内部产生金属屑(内部严重磨损)是Д-30КУ-154Ⅱ发动机主要常见和多发性故障之一。西北航空公司自1985年10月引进装有三台Д-30КУ-154Ⅱ发动机的图—154M型飞机以来,因发动机内部产生金属屑故障导致提前拆换发动机41台,约占装机总数的38%;占提前换发总数的64%;导致空中停车14次,占该型发动机空中停车总数的45%。Д-30КУ- 相似文献
2.
3.
5000千瓦级以下涡轴/涡桨、活塞发动机及50千牛级以下涡扇、涡喷发动机称为中小型航空发动机。这种发动机在世界航空发动机市场中产量份额高达80%,产值份额为50%左右。这表明它们在航空高新技术领域中占有举足轻重的地位,具有广泛的应用和发展前景,对其关键技术要给予特别关注 相似文献
4.
航空发动机故障诊断系统对提高发动机安全性和可靠性具有重要的意义,其性能评价指标包括故障检测率、故障定位率、虚警率等.为此,基于混合卡尔曼滤波器组诊断原理,针对民用航空发动机常见的四种故障搭建了发动机故障诊断系统.采用蒙特卡罗仿真方法,对故障诊断系统在发动机健康和性能退化两种情形下的性能评价指标进行了仿真验证.仿真结果表明,两种情形下诊断系统均满足发动机故障检测率98%以上、故障定位率90%以上、虚警率不大于1%的工程应用需求. 相似文献
5.
6.
在飞机过站时发现左发动机不起动,现象是按压发动机电门后,发动机转速上升至24%左右时,发动机转速下降至零,起动过程中断。 相似文献
7.
世界各航空发动机公司为保持在下一世纪航空动力领域的领先地位,都在寻求新的方法提高军用和民用发动机的性能,保持竞争能力。评定发动机性能的主要指标之一是推重比,预计在2O1O年军用发动机的推重比将提高50%,民用发动机将提高25%。 实现该目标一半将依靠材料改进,包括低温高分子复合材料和高温陶瓷材料,另一半则依靠改进设计准则、方法和程序。由于军用发动机材 相似文献
8.
为辨识航空发动机飞行过程中加减速瞬态模型,通过对某型航空发动机慢车至中间以及中间至慢车过程的飞行试验数据进行分析整理,将发动机上述加、减速过程简化为静态参数预测过程,利用3层前向人工神经网络,建立了某型发动机加、减速瞬态过程中的发动机关键参数预测模型,对发动机参数预测模型预测结果与飞行试验记录数据进行了对比分析,同时利用额外的飞行试验数据验证了辨识模型的泛化能力.结果表明:辨识得到的发动机模型在油门杆稳定时参数预测相对误差不超过3%,在油门杆动作期间参数预测相对误差不超过5%;验证点上辨识模型参数预测误差不超过3%.证明该型发动机参数预测模型可以很好地预测发动机瞬态过程中的参数变化情况.该方法为建立发动机其他状态的加、减速过程参数变化模型奠定了基础,也能为建立全包线范围内发动机瞬态参数预测模型提供参考. 相似文献
9.
10.
两种涡扇发动机部件特性自适应模型对比 总被引:3,自引:0,他引:3
发展了航空发动机自适应模型.并对以两种优化算法为基础的自适应模型进行了对比分析。两种模型以通用特性为基础运用优化方法,以发动机主要性能参数和过程参数偏差函数最小为优化目标,以部件特性耦合因子为被优参数,可以预测出不同飞行条件下的发动机风扇、压气机、燃烧室、高压涡轮、低压涡轮等部件特性。运用单纯形和遗传算法为基础的自适应模型对某型涡扇发动机性能的计算结果表明:相对于单纯形算法模型.遗传算法模型对发动机主要性能参数和过程参数的计算偏差降低了20%~30%;对发动机各截面总温、总压计算偏差降低了15%~20%;遗传算法模型相对于单纯形模型具有更为宽广的自适应模拟范围。对某型已知部件特性的涡扇发动机模拟结果显示.遗传算法模型部件特性模拟结果与已知部件特性差别甚微。 相似文献
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:3,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
13.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
14.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
15.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
16.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
17.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
18.
19.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
20.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献