大多普勒容限巴克码脉压

 本文介绍用补偿式非相干型旁瓣抑制滤波器(SSF)实现13位巴克码脉冲压缩旁瓣抑制的理论计算及实验结果。补偿式非相干型SSF采用最小二乘近似逆滤波方法设计,若子脉冲宽度为0.7μs,峰值旁瓣电平不超过-30dB,这种SSF的多普勒容限能达到-40kHz～+40kHz。理论计算及实验结果都表明,所设计的补偿式非相干型SSF的多普勒容限比具有同样长度冲激响应序列的R-G-ISSF有显著改善。     

一种基于线性规划的频率编码旁瓣抑制方法

频率编码信号具有较好的距离-多普勒分辨率、优良的低截获和抗干扰能力,但其旁瓣较高,不适用于检测动态范围大的海面多目标场合。采用失配滤波器法降低旁瓣电平会导致旁瓣宽度展宽,强目标旁瓣宽度展宽,反而遮盖了附近的弱目标。采用脉间码型捷变法,旁瓣抑制效果达不到实际应用要求。文章结合着2种方法,设计一种复合的旁瓣抑制方法。仿真结果表明,在相同信噪比损失和旁瓣宽度的情况下,本方法比失配滤波器法,峰值旁瓣比提高了7.5 dB;在积累相同的脉冲个数情况下,比脉间码型捷变法则提高了18 dB。     

短波地空通信多普勒频移对DTMF信号解码影响

DTMF信号具有优良的抗干扰性能和一定的抗多普勒频移的能力,广泛应用于语音信道的低速数据通信。文中分析了地-空短波通信的多普勒频移、基于Goertzel算法的DTMF信号解码基本原理和基本过程;在语音噪声背景下,基于Goertzel算法,解算了16个频点的信号幅值,对地—空短波通信的多普勒频移对DTMF信号解码性能的影响进行了仿真,得出了在语音和多普勒频移干扰的背景下,信噪比高于9dB时,基本可实现DTMF信号的高可靠检测的结论。     

低轨卫星多普勒频移特性的快速计算

地面站利用低轨卫星进行通信时,地面接收站接收信号存在明显的多普勒频移现象。为描述多普勒频移特性,首先分析卫星轨道偏心率对多普勒特性曲线的影响,分析表明：轨道偏心率越大,地面站接收信号多普勒变化率越大。其次,推导了卫星多普勒频移的计算表达式,并讨论了低轨卫星多普勒频移特性曲线的快速计算。仿真计算结果表明,该算法可以很好地描述任意低轨道卫星多普勒频移特性,并明显缩短了精确算法的计算时间,对于10 000km轨道高度卫星,算法置信度可达99%以上。     

辅助信息法消除宽带航空移动通信中的多普勒频移干扰研究

提出了一种利用辅助信息消除多普勒频移、减小子载波间干扰(ICI)、降低误码率的方法,即信息辅助抗多普勒频移方法(IAADO)。飞机利用自身配置的导航系统、监视等多种信息系统,可以实时或准实时地获得自身和周围飞机及地面站的位置、运动状态等信息,从而计算出接收信号的多普勒频移,并在此基础上采取频率补偿措施来消除多普勒频移在OFDM系统中产生的ICI。仿真结果表明,基于辅助信息的IAADO方法有效地解决了航空宽带移动通信中多普勒效应造成的强ICI干扰问题,提高了高速移动航路环境下的通信性能,IAADO和信道估计(导频点LS估计、线性插值)的联合使用可以进一步增强终端区环境下的通信性能。     

一种截获高速机动目标的方法

分析了采用滤波器组的方法截获快速机动目标存在的缺点,提出通过采用对回波信号进行FFT提取多普勒频移的方法得到目标的径向速度,并介绍了基4FFT算法原理,给出了采用FPGA设计FFT的方法。     

任意采样率变换数字重构滤波器设计

针对理想重构函数在数字信号域不可实现而直接截取性能较差的情况,根据信号重构理论和FIR（Finite Impulse Response,有限脉冲响应）滤波器窗函数设计法,分析不同窗函数、不同截取长度对重构滤波器的影响,提出一种凯塞窗任意采样率变换数字重构滤波器设计方法.该方法通过选择合适的窗参数、截取长度、重构滤波器时域精度和量化位数,有效控制阻带最小衰减抑制数字重构镜像.设计的数字重构滤波器已成功应用于某卫星基带调制解调器,符合镜像抑制大于65 dB的性能要求.     

基于动态RCS特征相似的直升机靶机旋翼设计

为获得具备全尺寸直升机旋翼动态雷达散射截面(RCS)特征的靶机相似性设计方案,首先建立适用于动态旋翼雷达回波信号提取与分析的RCS高频预估方法和时频分析方法。其次,开展了旋翼参数对其RCS时频域谱中的微多普勒特征和信号强度的影响特性研究。然后,推导得到反比形式的旋翼雷达最大微多普勒频移的相似性条件,发现依据相似性条件设计较小半径、较少桨叶片数的靶机旋翼能够模拟出目标旋翼的雷达微多普勒特征,进一步通过改变翼型厚度能够使靶机旋翼具有与目标旋翼接近的RCS信号强度。最后,综合对比不同设计方案的靶机旋翼动态RCS的频域和时域特征,提出模拟目标旋翼雷达散射特性的择优方案：雷达最大微多普勒频移相同、RCS强度相似性误差小于0.408 dB,实现了靶机旋翼对目标旋翼RCS时频特征相似性的设计。     

导航辅助下基于LAS码的天基多目标测控

中继卫星的天基测控是解决中低轨道航天器大范围、长时间、多目标测控的有效途径,但用户星到中继卫星的时延误差、多普勒频移校正误差等参数会对多目标测控带来干扰。针对该问题,首先分析了定位误差引起的时延误差、多普勒频移校正误差等因素,设计了天基多目标前向链路遥控SMA(S-band Multiple Access,S频段多址)信号形式和反向遥测链路SMA信号形式,选择与时延校正误差相匹配的LAS(Large Area Synchronous,大区域同步)码作为反向遥测信息的扩频码,建立了导航辅助的终端时延和频率预校正方案模型,可以有效消除多用户干扰。仿真表明,当Eb/N0≥10.5dB时,前向遥控信息误码率pe≤1×10~(-6),反向遥测信息误码率pe≤1×10~(-6),使用LAS码比Gold序列约有2dB性能改善,为基于我国天链卫星的中低轨道卫星稳定运行、载人航天交会对接以及后续空间站建设等任务的测控提供重要参考。     

基于频移递推的机载单站无源测距

在机载站飞行方向前方某一距离处的多普勒频移能够通过递推计算的方法由站点当前位置处的相位测量结果而被直接确定。进一步利用频移和角度之间的变换,由多普勒频移的虚拟递推值即可求得载机飞行路线前方虚拟距离处的目标方位,由此就可在机载单站平台上通过三角定位法,实现仅基于相差测量的无源测距。     

Optimum Mismatched Filters for Sidelobe Suppression

This paper discusses the application of least-mean-squares approximate inverse filtering techniques to radar range sidelobe reduction. The method is illustrated by application to the 13-element Barker code. The performance of the least-mean-square inverse filter is compared with the matched filter and with the simplified sidelobereducing filters of Rihaczek and Golden. A filter which completely suppresses the range sidelobes of a 13-element Barker sequence is only 0.2 dB worse than a matched filter in noise.     

A new algorithm to optimize Barker code sidelobe suppressionfilters

The authors suggest a new algorithm for binary coding waveform sidelobe reduction after matched filtering and present a general method by which optimized sidelobe suppression filters for Barker codes can be obtained with a peak output sidelobe 2.62 dB lower than the results found in the literature (for 13-b Barker code). This optimization algorithm is also promising for other binary coding waveforms, such as truncated pseudonoise (PN) sequences and concatenated codes. This new approach can readily be applied to sidelobe-reduction filter design for other binary coding waveforms, such as truncated PN sequences, concatenated codes, etc., which often find their applications in radar systems and spread spectrum communication systems     

Poly-phase codes and optimal filters for multiple user ranging

A technique is introduced to select poly-phase codes and optimal filters of a pulse compression system that have specific temporal and frequency characteristics. In the particular problem under study, multiple vehicles are assigned unique codes and receiver filters that have nearly orthogonal signatures. Narrowband users, that act as interference, are also present within the system. A code selection algorithm is used to select codes which have low autocorrelation sidelobes and low cross correlation peaks. Optimal mismatched filters are designed for these codes which minimize the peak values in the autocorrelation and the cross correlation functions. An adjustment to the filter design technique produces filters with nulls in their frequency response, in addition to having low correlation peaks. The method produces good codes and filters for a four-user system with length 34 four-phase codes. There is considerable improvement in cross and autocorrelation sidelobe levels over the matched filter case with only a slight decrease in the signal-to-noise ratio (SNR) of the system. The mismatched filter design also allows the design of frequency nulls at any frequency with arbitrary null attenuation, null width, and sidelobe level, at the cost of a slight decrease in processing gain     

Minimum Peak Range Sidelobe Filters for Binary Phase-Coded Waveforms

Linear programming techniques are utilized to determine the optimal filter weights for minimizing the peak range sidelobes of a binary phase-coded waveform. The resulting filter is compared with the filter obtained by use of the least square approximation to the ideal inverse filter. For a test case using the 13-element Barker code the linear programming filter is found to have peak sidelobes as much as 5 dB lower than the least squares filter of the same length.     

Sequence design for IIR inverse filter pulse compression

An infinite impulse response (IIR) inverse filter structure is presented, and compared with the performance of two finite impulse response (FIR) designs. The IIR design is shown to provide better performance and be able to improve further (e.g., -1.4 dB in sidelobe levels per unit delay increase for the length-13 Barker sequence) by increasing delay. The performance parameters of this IIR inverse filter suggest a design criterion for sequences on which the filter operates; that is related to the roots of the Z transform polynomial of the sequence. The sidelobe-optimal sequence derived according to this criterion is shown to provide sharper sidelobe reduction (-6 dB per unit delay increase for the sidelobe optimal length-13 sequence)     

Improved Range Resolution Filters for Rectangular-Pulse Radar Systems

The performance of several new clutter-reduction filters suitable for rectangular-pulse radar systems is investigated. The new filters consist of various approximations and modifications of two filters known to be optimal for certain criteria: the well-known Urkowitz filter which optiizes the clutter improvement ratio, and the newer sidelobe reduction filter which minimizes output noise power subject to peak sidelobe constaints. The new filters are compared usig five basic criteria: clutter improvement ratio, signal-to-noise ratio, sidelobe peak ratio, pulse compression ratio, and filter complexity. The results are summarized in tabular and graphical form.     

基于LAS码的星群多目标测控技术研究

针对星群多目标同时测控问题,基于星群轨道根数的时延特性和多普勒频移特性分析可得,星群多目标测控的上行链路遥控与测距信号可实现S CDMA（Synchronous Code Division Multiple Access,同步码分多址）,由于星间距离较小,下行链路遥测与测距信号满足QS CDMA（Quasi synchronous code division multiple access,准同步码分多址）.上行链路遥控和测距信号形式设计为PCM BPSK CDMA（Pulse Code Modulation Binary Phase Shift Keying Code Division Multiple Access,脉冲编码调制二进制相移键控码分多址）,上行链路信号采用Gold序列扩频;下行链路遥测和测距信号形式设计为PCM BPSK CDMA,根据总的时延差,提出下行链路采用基于等长脉冲间隔法构造的LAS（Large Area Synchronous,大区域同步）码扩频.结果表明：比特信噪比Eb/N0为10.5 dB时,遥控误码率为1＆#215;10 6;Eb/N0为9.6 dB时,遥测误码率为1×10^5——与达到相同误码性能的Gold序列相比有1 dB改善,因此,LAS码相比于Gold码能够获得更好的误码性能.     

Range sidelobe reduction for the quadriphase codes

Filters that reduce the sidelobes of the quadriphase-coded waveform are realized by applying the biphase-to-quadriphase transformation to the filter designs that reduce the sidelobes of the prototype biphase code. The mismatch loss is invariant under this transformation, but the resulting peak-to-sidelobe ratio (PSR) can decrease 1.5 dB maximum. An example illustrates the procedure for a compressor composed of a sidelobe reducing filter cascaded with the matched filter and a compressor realized as one mismatched filter     

航空通信中基于PN码的信道估计算法研究

航空移动通信系统（空空信道）中,大的多径时延和多普勒频移会造成非常严重的符号间干扰,高速宽带下尤为突出,使得传统的频域信道估计算法不得不通过提高运算长度和复杂度来实现性能,而航空通信对实时性的要求使其难以工程实现。本文针对空空信道时延长而衰落小的条件,提出一种基于PN码的时域信道估计算法,连续发送N段m序列作为训练序列...