基于双GPS接收机的精密定向研究

GPS定位系统除了可以进行定位、测速和授时外 ,还可以利用两个或多个GPS测量值进行方位测量和三轴姿态测量。文章对利用两块GPSOEM板同步接收的载波相位观测量来精密测定方位进行了深入研究。首先利用载波相位的双差观测方程 ;再根据两个天线间距离已知这个条件 ,对方位和俯仰进行二维搜索 ,并采用了模糊度函数作为搜索的判断依据 ;最后根据最小二乘计算出两个天线的基线矢量 ,从而最终计算出精密的方位值和俯仰角。经过大量的试验表明 ,该算法是切实可行的 ,在 5m基线下 ,方位精度达到 0 0 8°,而且定向时间一般只需 1min左右     

电离层不规则结构对GPS性能的影响

电离层不规则结构的存在可引起无线电信号的幅度和相位发生随机起伏, 这 种电离层闪烁现象会影响全球定位系统(Global Positioning System, GPS)的 性能, 降低定位精度, 严重时导致信号失锁. 电离层不规则结构对GPS性能的 影响涉及电离层物理、接收机设计和表征卫星几何分布的精度衰减因子(Dilution of Positioning, DOP)等多方面因素. 本文通过对表征电离层不规则结构参数 的分析, 根据GPS接收机跟踪环路和闪烁信号模型, 综合研究了电离层闪烁对 GPS接收机载波跟踪环和码跟踪环跟踪误差的影响; 结合实际观测, 评述 了电离层不规则结构对单频和双频GPS接收机定位性能的影响, 在此基础上 提出了有待深入研究的问题及具体建议.      

Multivariate bootstrapped relative positioning of spacecraft using GPS L1/Galileo E1 signals

GNSS-based precise relative positioning between spacecraft normally requires dual frequency observations, whereas attitude determination of the spacecraft, mainly due to the stronger model given by the a priori knowledge of the length and geometry of the baselines, can be performed precisely using only single frequency observations. When the Galileo signals will come available, the number of observations at the L1 frequency will increase as we will have a GPS and Galileo multi-constellation. Moreover the L1 observations of the Galileo system and modernized GPS are more precise than legacy GPS and this, combined with the increased number of observations, will result in a stronger model for single frequency relative positioning. In this contribution we will develop an even stronger model by combining the attitude determination problem with relative positioning. The attitude determination problem will be solved by the recently developed Multivariate Constrained (MC-) LAMBDA method. We will do this for each spacecraft and use the outcome for an ambiguity constrained solution on the baseline between the spacecraft. In this way the solution for the unconstrained baseline is bootstrapped from the MC-LAMBDA solutions of each spacecraft in what is called: multivariate bootstrapped relative positioning. The developed approach will be compared in simulations with relative positioning using a single antenna at each spacecraft (standard LAMBDA) and a vectorial bootstrapping approach. In the simulations we will analyze single epoch, single frequency success rates as the most challenging application. The difference in performance for the approaches for single epoch solutions, is a good indication of the strength of the underlying models. As the multivariate bootstrapping approach has a stronger model by applying information on the geometry of the constrained baselines, for applications with large observation noise and limited number of observations this will result in a better performance compared to the vectorial bootstrapping approach. Compared with standard LAMBDA, it can reach a 59% higher success rate for ambiguity resolution. The higher success rate on the unconstrained baseline between the platforms comes without extra computational load as the constrained baseline(s) problem has to be solved for attitude determination and this information can be applied for relative positioning.     

新的GPS单频单历元定姿算法

LAMBDA算法依赖于初始的模糊度浮点解,但仅用载波相位观测方程需要多个历元才能获得浮点解,将导致初始化时间过长.针对这一问题,对GPS(Global Positioning System)单历元的载波相位单差方程进行特殊变换,将未知的整周模糊度看成噪声,从而构造出新的观测方程,和原始的观测方程进行组合求解,克服了仅用载波相位双差观测方程因为亏秩而无法在单历元获得浮点解的缺点,解决了初始化时间的问题.通过深入研究浮点解和固定解之间的关系,提出一种将低精度浮点解映射到固定解的方法,降低了LAMBDA算法对高精度浮点解的依赖性,避免了用多个历元获取浮点解的高精度,从而实现了单频、单历元的整周模糊度估计.通过实际测试,该算法成功率高于97%,能够有效地用于实时动态姿态解算.      

单频GPS动态相对定位的模糊度逼近/搜索解法

针对目前实时动态定位(RTK)中常用搜索解法可靠度不高的缺点,利用各历元诸双差方程所形成的法方程,对其进行解耦处理以便于实时计算.在此基础上综合了逼近、搜索两种解法各自的局部优势,构成了逼近/搜索的联合解法.实际测试表明,该算法在单频全球定位系统(GPS)载波相位差分的动态相对定位过程中,用2～3min的时间即可可靠地在航解算出整周模糊度.     

基于实时SSR数据的LEO卫星精密单点定位研究

对目前低轨卫星实时定位的方法进行了研究,现在通常采用GPS定位,使用广播星历和普通晶振,实时定位精度一般在10m以内,不能满足高精度实时定位的需求。IGS组织在全球范围内对GPS跟踪分析,生成精密星历、精密钟差产品、按SSR格式的广播星历和钟差修正产品并在网上发布。对这些IGS产品进行了调查,提出在现有测控支持情况下,可以通过高密度上注SSR信息流实现在轨高精度定位。以某型号低轨微小卫星在轨导航增强载荷为应用背景,用IGS03产品中的1057和1058数据对双频GPS接收机的星历和钟差进行修正,采用递推最小二乘估计和LAMDA模糊度固定过对载波相位和伪距信息进行处理,在短时间内获得亚米级定位结果。     

Influence of different data fusion methods on the accuracy of three-dimensional displacements field

Combining multi-source data can improve the accuracy and the spatial resolution of the three-dimensional (3-D) displacements field. How to effectively integrate multi-source data to obtain high-precision and high spatial resolution 3-D displacements field is worthy of further study. The stochastic model and fusion model of integrating multi-source data affect the accuracy of data fusion. In this paper, based on the least squares method, the effects of different stochastic models and data fusion models on the 3-D displacements field’s accuracy are studied. The optimal method for estimating large-scale 3-D displacements field from integrated InSAR, leveling and GPS measurements is obtained. Then we realize the integrating InSAR, leveling and GPS measurements to obtain the high-precision 3-D displacements velocity field in Tianjin (China) from 2016 to 2018. The results are validated with GPS measurements at 6 independent stations, with the root mean squares (RMS) residuals of the discrepancies being 2.39 mm/yr, 2.54 mm/yr and 2.83 mm/yr in eastern, northern and vertical directions, respectively. By comparing different stochastic models, the 3-D displacements field obtained from multi-source data is optimized by the variance component estimation-least squares method, which is better than weighted least squares (WLS) method. By comparing different data fusion models, the accuracy of the horizontal displacements velocity is better than that of interpolated GPS results. The horizontal displacements component has a great influence on the vertical displacements velocity accuracy in the process of acquiring the 3-D displacements velocity by integrating InSAR, GPS and leveling measurements. This study provides a reference method for integrating multi-source data to obtain 3-D displacements field. This method effectively utilizes the advantages of GPS, InSAR and leveling measurements, and extends the limitations of single technical in describing surface-time scale applications. The 3-D displacements information with a large spatial scale and high spatial resolution provide a reliable data basis for studying the crustal movement and its dynamic mechanism.     

基于双频GPS观测的简化动力学最小二乘批处理精密定轨

星载双频GPS载波相位和伪距观测量已成为低轨卫星获取精确三维位置和速度信息的主要方式. 本文以非差消电离载波相位和伪距组合作为观测量,应用简化动力学最小二乘批处理方法进行地球低轨卫星的精密定轨,并给出完整定轨流程. 采用逐段常量的经验加速度对动力学模型误差进行补偿,描述了经验加速度敏感矩阵及稀疏带状矩阵求逆的有效计算方法. 利用GRACE-A卫星GPS观测数据对定轨位置精度进行分析,结果显示,三维位置定轨精度优于5cm,经验加速度在径向、切向和法向上的补偿水平不超过40nm·s-2,大气阻力系数和辐射光压系数的估计值符合物理实际,星载接收机钟差大致呈线性并具有短周期小波动.      

基于RTK-GPS的提梁机组协调控制系统设计

双提梁机组协调控制系统利用对称布置的双频载波相位RTK-GPS(Real-Time Kinematic difference Global Position System )接收机完成对提梁机位置、航向位姿信息的测量,通过卡尔曼滤波与里程计融合,消除坐标定位信息的波动,提高位姿测定的精度;单机采用基于CAN (Controller Area Network)总线的网络控制系统,机组间数据传输采用无线网络,构成混合网络控制系统;采用基于双闭环的同步控制策略实现对两提梁机的同步协调控制.实际应用结果表明,两提梁机间相对位置偏差不超过0.1m,相对航向角度偏差不超过0.1°.      

时钟偏差辅助的GPS完整性监测算法

对伪距残差最小二乘的接收机自主完整性监测(RAIM)算法进行了分析.在此基础上,通过对接收机时钟偏差的建模,将模型预测的时钟偏差引入伪距残差最小二乘的RAIM算法中,保证了在可见星仅为4颗的情况下,仍能利用χ2检验法对全球定位系统(GPS)进行完整性监测,从而达到提高完整性监测算法有效性的目的.计算机仿真的结果显示,这种辅助方式不仅计算简单,而且有效可行.      

Ionospheric path delay models for spaceborne GPS receivers flying in formation with large baselines

GPS relative navigation filters could benefit notably from an accurate modeling of the ionospheric delays, especially over large baselines (>100 km) where double difference delays can be higher than several carrier wavelengths. This paper analyzes the capability of ionospheric path delay models proposed for spaceborne GPS receivers in predicting both zero-difference and double difference ionospheric delays. We specifically refer to relatively simple ionospheric models, which are suitable for real-time filtering schemes. Specifically, two ionospheric delay models are evaluated, one assuming an isotropic electron density and the other considering the effect on the electron density of the Sun aspect angle. The prediction capability of these models is investigated by comparing predicted ionospheric delays with measured ones on real flight data from the Gravity Recovery and Climate Experiment mission, in which two satellites fly separated of more than 200 km. Results demonstrate that both models exhibit a correlation in the excess of 80% between predicted and measured double-difference ionospheric delays. Despite its higher simplicity, the isotropic model performs better than the model including the Sun effect, being able to predict double differenced delays with accuracy smaller than the carrier wavelength in most cases. The model is thus fit for supporting integer ambiguity fixing in real-time filters for relative navigation over large baselines. Concerning zero-difference ionospheric delays, results demonstrate that delays predicted by the isotropic model are highly correlated (around 90%) with those estimated using GPS measurements. However, the difference between predicted and measured delays has a root mean square error in the excess of 30 cm. Thus, the zero-difference ionospheric delays model is not likely to be an alternative to methods exploiting carrier-phase observables for cancelling out the ionosphere contribution in single-frequency absolute navigation filters.     

Enhancing the kinematic precise orbit determination of low earth orbiters using GPS receiver clock modelling

Clock error estimation has been the focus of a great deal of research because of the extensive usage of clocks in GPS positioning applications. The receiver clock error in the spacecraft orbit determination is commonly estimated on an epoch-by-epoch basis, along with the spacecraft’s position. However, due to the high correlation between the spacecraft orbit altitude and the receiver clock parameters, estimates of the radial component are degraded in the kinematic approach. Using clocks with high stability, the predictable behaviour of the receiver oscillator can be exploited to improve the positioning accuracy, especially for the radial component. This paper introduces two GPS receiver clock models to describe the deterministic and stochastic property of the receiver clock, both of which can improve the accuracy of kinematic orbit determination for spacecraft in low earth orbit. In particular, the clock parameters are estimated as time offset and frequency offset in the two-state model. The frequency drift is also estimated as an unknown parameter in the three-state model. Additionally, residual non-deterministic random errors such as frequency white noise, frequency random walk noise and frequency random run noise are modelled. Test results indicate that the positioning accuracy could be improved significantly using one day of GRACE flight data. In particular, the error of the radial component was reduced by over 40.0% in the real-time scenario.     

多频GNSS电离层折射误差修正方法CSCD

针对电离层折射误差较大的特点,分别对GPS(Global Positioning System)和BDS(Bei Dou Navigation Satellite System)的单一频率的电离层折射误差进行了分析,并将不同频率进行线性组合,计算出组合后的电离层折射误差。此方法修正了双频一阶项、三频一阶项和三频二阶项电离层折射误差。由于电离层延迟修正的同时会放大观测噪声,为此分析比较了不同频率组合修正后的观测噪声,为最佳频率组合的选取提供了理论方法。     

Quality variation of GPS satellite clocks on-orbit using IGS clock products

Over 60% clocks on board of the GPS satellites are working longer than their designed life. Therefore realizing their stabilities in a long time scales is essential to GPS navigation and positioning plus IGS time scale maintaining. IGS clock products from 2001 to 2010 are used to analyze the GPS satellite clock qualities such as frequency stabilities and clock noise level. We find out that for the clocks of Block IIA satellites the frequency stabilities and clock noise are 10 times worse than that of the Block IIR and IIR-M satellites. Moreover, the linear relationships between frequency stabilities and clock residuals have been deduced with an accuracy of better than 0.02 ns. Specially, it is noticed that the clock of the PRN27 is instable and the relationship between the frequency stability and residuals is at least a quadratic curve. Therefore, we suggested that GPS satellite clocks should be weighted by their quality levels in application, and the observations of the Block IIA should not be used for real-time positioning which required precision better than one meter.     

GNSS receiver clock modeling when using high-precision oscillators and its impact on PPP

Processing data from Global Navigation Satellite Systems (GNSS) always requires time synchronization between transmitter and receiver clocks. Due to the limited stability of the receiver’s internal oscillator, the offset of the receiver clock with respect to the system time has to be estimated for every observation epoch or eliminated by processing differences between simultaneous observations. If, in contrast, the internal oscillator of the receiver is replaced by a stable atomic clock one can try to model the receiver clock offset, instead of estimating it on an epoch-by-epoch basis. In view of the progress made in the field of high-precision frequency standards we will investigate the technical requirements for GNSS receiver clock modeling at the carrier phase level and analyze its impact on the precision of the position estimates.     

工作频率选择对GNSS接收机通道跟踪环路的影响CSCD

GNSS接收机因须并行接收处理大量卫星信号,使用通道数量较多,功耗大是其主要难题,降低功耗的解决方法之一是让通道工作时钟采用较低的频率。通过分析工作时钟与所需处理的伪码频率的关系,本文给出了通道时钟频率对伪码相位分辨率和相位抖动幅度的影响。选取两种频率的工作时钟进行仿真实验,结果表明在相同仿真条件下,选用21MHz工作时钟与选用63MHz工作时钟相比,接收机的伪码测量精度、载波测量精度均下降1倍左右,但其引入的测量误差仍小于理论估算结果,选取较低的工作时钟频率是兼顾功耗与精度的折中方法,适合作为工程设计方案。     

基于长短时记忆神经网络(LSTM)的钟差预报算法

原子钟钟差预报在原子时计算和原子钟频率驾驭中发挥着重要的作用。长短时记忆神经网络（LSTM）预报算法能够处理多参数长期依赖关系的时间序列预报，以氢钟和铯钟实测数据为样本，通过构建LSTM钟差预报模型，降低了长期原子钟内部噪声以及原子钟漂移对钟差预报的影响，并以72h，240h和720h为预报时长，分别与线性多项式模型、灰色模型和Kalman模型原子钟钟差预报模型进行预报误差对比。研究表明，在240h以上的预报时长中，LSTM建模长期依赖关系的优势得以体现，相较于其他3类模型可以获得更高的预报精度。     

GPS data processing of networks with mixed single- and dual-frequency receivers for deformation monitoring

In order to obtain crustal deformations of higher spatial resolution, existing GPS networks must be densified. This densification can be carried out using single-frequency receivers at moderate costs. However, ionospheric delay handling is required in the data processing. We adapt the Satellite-specific Epoch-differenced Ionospheric Delay model (SEID) for GPS networks with mixed single- and dual-frequency receivers. The SEID model is modified to utilize the observations from the three nearest dual-frequency reference stations in order to avoid contaminations from more remote stations. As data of only three stations are used, an efficient missing data constructing approach with polynomial fitting is implemented to minimize data losses. Data from large scale reference networks extended with single-frequency receivers can now be processed, based on the adapted SEID model. A new data processing scheme is developed in order to make use of existing GPS data processing software packages without any modifications. This processing scheme is evaluated using a sub-network of the German SAPOS network. The results verify that the new scheme provides an efficient way to densify existing GPS networks with single-frequency receivers.     

Doppler utilised Kalman estimation (DUKE) of ionospheric delay for satellite navigation

The ionospheric delay experienced by the satellite navigation signals depends upon the Total Electron Content (TEC) and needs to be corrected. While the single frequency receivers always use parametric models to correct this delay, dual frequency receivers, when suffers a loss of lock of one of its signal, also has to resort to these models. Here, an alternative method, based on Doppler, surrogated by range rate variation, has been attempted to estimate the ionospheric delay using a Kalman filter. GPS data have been used for all visible satellites over four days selected around the equinox and solstice with nominal geomagnetic conditions and estimations done in continuous and calibrated modes. Results of continuous estimation, obtained for a mid latitude station, showed moderate accuracy while it was significantly better for the calibrated mode with no seasonal dependence. Estimations done for station within the extent of equatorial anomaly, has not only resulted in relative deterioration in performance, but also shown seasonal dependence. Compared with estimates of Klobuchar model, the Calibrated estimation showed superior performance, conspicuously in the mid latitude station. However, for the continuous mode, performance was at par with the model at higher latitudes but inferior to it in regions within the extent of the equatorial anomaly.     

GPS信号捕获与跟踪策略确定及实现

为了检测GPS(Global Positioning System)信号,设计了码环及载波环捕获与跟踪数字系统.序贯搜索与窄间隔超前-滞后型数字延迟锁相环的采用,保证了码相位的可靠捕获与精确跟踪,四相鉴频器、叉积自动频率跟踪算法及科思塔环载波相位跟踪算法的结合,既保证了载波频率(多普勒频移)的捕获速度,又使环路能有效地跟踪频率/相位变化,获得较好的动态性能与噪声性能.控制算法及参数确定的软化实现使系统具有较好的灵活性.基于扩频相关器与数字信号处理器的数字系统验证了上述方案的正确性及有效性.