空间光学精密展开机构展开方法的初步探讨

文章对空间光学精密展开机构(以下简称展开机构)进行分类,分析了几种典型可展开空间光学系统的展开方法和特点。讨论了展开机构设计需要考虑的主要因素,并给出设计建议。     

多向编织碳／碳复合材料的强度与断裂

本文研究了细编穿刺三向Ｃ／Ｃ复合材料的拉压特性，分析相应的微观破坏模式，实测了Ｃ／Ｃ复合材料中Ｚ向纤维束力学性能的统计分布规律。结果表彰：细编穿刺三向Ｃ／Ｃ复合材料在拉伸和压缩载荷作用下具有双模量和呈现非线性。Ｚ向强度受穿刺纤维束纤维根数和间距控制，用最弱环连接理论考虑Ｚ向纤维强度的统计分布，预报σ－ε关系与实验符合较好。ＸＹ向强度由碳布强度贡献，其破坏主要是碳布层间的拉剪断裂。     

Preparation,Growth Mechanisms and Characterizations of ZnSe Films via the Solvothermal Method

With diethylamine as a solvent, ZnSe films were formed on the Si substrate directly from zinc and selenium through the modified solvothermal method. The effects of holding temperature, deposition time and substrate surface treatment on the quality and morpholo-gies of the ZnSe films were investigated. The growth mechanism of ZnSe films was proved to be a layer-nucleation growth process, which was tied in with the Stranski-Krastanov (SK) model. ZnSe films were identified by the X-ray diffraction pattern (XRD), the scan-ning electron microscope (SEM), the X-ray photoelectron spectroscope (XPS) and the photoluminescence (PL) techniques. The results indicate that the modified solvothermal method with diethylamine as a solvent is suitable to prepare high quality ZnSe films.     

含闭链机构机器人动力学探讨

本文用Appell方程就含闭链机构机器人动力学研究作了新的探讨,给出了建立含闭链机构机器人动力学方程的一般方法。旨在把含闭链机构机器人分解成相应的开链机构进行研究,因而大大简化了推导过程。文中通过一个实际工业机器人动力学方程的推导,证实了该方法的可行性。     

大型转动机械碰摩故障分析的声发射检测系统

汽轮发电机、空气压缩机等采用油膜支撑的大型转动机械,由于安装或运行中的原因,在转子旋转过程中,可能和器壁发生轻微的摩擦和碰击,简称碰摩.声发射技术在碰摩发生特别是故障早期诊断上有优越性.本系统的特点是没有沿用传统的计数、幅度、能量和持续时间等声发射特性参数,而是在声发射包络信号的频率分析中进行特征提取.声发射发生的过程分析和现场试验都表明这种方法对碰摩检测很敏感,在碰摩发生的起始阶段,包络谱中与转速同步的周期性分量显著增加.根据这种新的设计思想自行研制了BUAA碰摩声发射检测仪并对此作了介绍.     

Spectra and time variability of black-hole binaries in the low/hard state

We propose a jet model for the low/hard state of galactic black-hole X-ray sources which explains the energy spectra from radio to X-rays and a number of timing properties in the X-ray domain such as the time lag spectra, the hardening of the power density spectra and the narrowing of the autocorrelation function with increasing photon energy. The model assumes that (i) there is a magnetic field along the axis of the jet, (ii) the electron density in the jet drops inversely proportional to distance, (iii) the jet is “hotter” near its center than at its periphery, and (iv) the electrons in the jet follow a power-law distribution function. We have performed Monte Carlo simulations of Compton upscattering of soft photons from the accretion disk and have found power-law high-energy spectra with photon-number index in the range 1.5–2 and cutoff at a few hundred keV, power-law time lags versus Fourier frequency with index 0.8, and an increase of the rms amplitude of variability and a narrowing of the autocorrelation function with increasing photon energy as they have been observed in Cygnus X-1. The spectrum at long wavelengths (radio, infrared, optical) is modeled to come from synchrotron radiation of the energetic electrons in the jet. We find flat to inverted radio spectra that extend from the radio up to about the optical band. For magnetic field strengths of the order 10⁵–10⁶ G at the base of the jet, the calculated spectra agree well in slope and flux with the observations.     

铝合金厚板搅拌摩擦焊焊缝疏松缺陷形成机理

采用圆锥形搅拌头焊接20mm厚的7075-T6铝板,分析焊接过程中焊缝内部疏松缺陷的形成过程及原因。研究表明,焊缝表面成形良好,无明显缺陷。但是,在焊缝轴肩区和焊核区之间出现了疏松缺陷。分析认为,焊缝上、下部金属温度差太大,导致其塑性流动行为发生变化是疏松缺陷形成的主要原因。搅拌摩擦焊(FSW)过程中,焊缝上部金属温度较高,而底部温度仍然很低,脱离搅拌针端部的塑化金属在周围冷金属巨大的变形抗力作用下转而沿搅拌针表面往上迁移。到达轴肩区下方汇聚区时,由于轴肩区金属温度高,向下的挤压力太小,导致回迁上来的塑化金属继续往上迁移并冲破轴肩区而沿轴肩边缘溢出形成飞边。汇聚区内没有足够的塑化金属填充、焊缝无法被压实而产生疏松孔洞。通过建立疏松缺陷形成的物理模型,可以更直观地反映出焊缝金属流动形态及缺陷形成过程。     

Modeling the broadband persistent emission of magnetars

In this paper, we discuss our first attempts to model the broadband persistent emission of magnetars within a self-consistent, physical scenario. We present the predictions of a synthetic model that we calculated with a new Monte Carlo 3D radiative code. The basic idea is that soft thermal photons (e.g. emitted by the star surface) can experience resonant cyclotron upscattering by a population of relativistic electrons treated in the twisted magnetosphere. Our code is specifically tailored to work in the ultra-magnetized regime; polarization and QED effects are consistently accounted for, as well different configurations for the magnetosphere. We discuss the predicted spectral properties in the 0.1–1000 keV range, the polarization properties, and we present the model application to a sample of magnetars soft X-ray spectra.     

The beaming of external Compton emission

We consider a relativistically moving blob consisting of an isotropic electron distribution that Compton-scatters photons from an external isotropic radiation field. We compute the resulting beaming pattern, i.e. the distribution of the scattered photons, in the blob frame as well as in the observer’s frame by using the full Klein–Nishina cross section and the exact incident photon distribution. In the Thomson regime the comparison of our approach with Dermer (1995) results in concurrent characteristics but different absolute number of the scattered photons by a factor of f_corr = 3.09. Additionally, our calculation yields a slightly lower boost factor which varies the more from the corresponding value in Dermer (1995) the higher the spectral index p of the electron distribution gets.     

热障涂层在涡轮叶片应用中的热防护有效性

建立了含热障涂层的涡轮叶片简化传热模型,通过理论推导建立了热障涂层的有效性判据,并基于此进行了热防护有效性分析。理论分析与数值实验表明:由热障涂层带来的复合传热表面传热系数的变化会显著影响热障涂层的热防护效果；在发动机典型工况下,对于处于高温区的高压涡轮叶片前缘处,热障涂层引起的复合传热表面传热系数变化率最大值的范围为1.25%~10.83%以满足热防护有效性要求。在工程中应特别注意由于热障涂层的应用带来的复合传热表面传热系数的变化,否则会导致热防护失效,甚至产生反效果。