大涵道比涡扇发动机TPS短舱低速气动特性分析

为了评估民机低速带动力试验时进排气效应的影响,选取大涵道比发动机涡轮动力模拟器(TPS)短舱和真实发动机短舱作为研究对象,采用数值模拟方法对其起飞、进近状态的低速气动特性进行对比分析。结果表明:由于TPS流量低于真实发动机需求,其唇口、外罩流场特征和真实发动机短舱有所不同,阻力特性也有差别;在进气道处于亚临界状态时,TPS短舱阻力系数比真实短舱大了约1.7个阻力单位,又由于唇口当地气流攻角更大,使得TPS短舱失速攻角相对降低了约1.0°;当进气道工作于超临界状态时,TPS短舱虽然也可以反映真实短舱的流动特性,但由于捕获流管收缩情况和气流驻点随攻角的变化,使得在0°~20°攻角时TPS短舱的阻力系数高于真实短舱,而在20°~30°攻角时其阻力系数略低,差量最大约为1.8个阻力单位。对于研究的大涵道比发动机,未经唇口及外罩修正的TPS短舱其低速气动特性基本可以反映真实进排气效应的影响,但在气动特性分析中可以考虑进一步修正进气效应的影响。     

周向总压畸变对对转压气机影响效应分析

以对转压气机为研究对象,在数值方法校验的基础上,应用全通道定常流场分析手段计算了对转压气机不同周向畸变条件下的三维流场,获取了周向总压进气畸变对该压气机性能以及流场结构的影响效应,确定了对转压气机的临界畸变角,分析了不同畸变强度对压气机性能的影响规律,探讨了周向总压畸变在对转压气机中的发展演化过程。结果表明:(a)所研究的对转压气机临界畸变角约为72°,略高于传统动-静叶排交替的压气机临界畸变角;(b)相比均匀进气工况,当畸变指数为0.24时,对转压气机失速点压比和失速裕度分别下降3%和9.6%,当畸变指数为0.5时二者分别下降8.3%和19.8%;(c)未畸变区与畸变区流体之间存在的压力梯度影响转子叶片相对来流速度。进入畸变区叶片来流相对速度减小,负荷降低,退出畸变区叶片来流相对速度增大,负荷增大;(d)上游转子使得畸变水平提高,下游转子反向旋转效应抑制了来流相对速度变化趋势,增强了气流在其叶片通道中的掺混,使得畸变水平有所下降。     

冲压发动机用轴对称进气道设计和试验

完成了一种Ma=2.5～4.0冲压发动机用超声速轴对称混合式进气道模型的设计,通过数值模拟和风洞试验,获得了马赫数Ma=2.5,3.0,3.5,4.0,攻角α=0°,3°,6°,8°条件下的超声速轴对称混合式进气道性能。试验结果表明,随着马赫数的增加,总压恢复系数大幅度下降,亚临界稳定范围变窄,流量系数逐渐增加;随着攻角的增大,总压恢复系数和流量系数总体都呈降低趋势,在Ma≥3.0,α=6°时,进气道性能的下降小于5%,亚临界稳定范围变窄。     

Experimental study of a controlled variable double-baffle distortion generator engine test rig

In order to explore the total-pressure distortion test assessment method for a turbofan engine, a Controlled Variable Double-Baffle Distortion Generator(CVDBDG) with a horizontal symmetry moving form was developed, which can adjust the steady-state and time–variant distortion separately in real time. The inlet total-pressure distortion test was conducted on an afterburner turbofan engine. The distortion parameters of CVDBDG and the instability characteristics of the engine were measured. The experimental data were modeled and analyzed by using back propagation artificial neural networks, and the work envelope of CVDBDG was obtained. Based on the analysis of the data on the engine's instability, the properties of CVDBDG used for the stability assessment were preliminarily evaluated. The results show that CVDBDG can simulate both steady-state and time–variant distortions simultaneously in a range determined by three envelopes.Under the condition of symmetric double baffles, a critical depth of insertion exists, beyond which the symmetric baffles will generate an asymmetric flow field. In the case of double baffles, compared to a single baffle, the engine exhibited different instability characteristics. Based on CVDBDG, it is expected that more efficient engine stability and durability assessment methods can be developed.     

高速进气道抛罩过程内流场演化特性研究

为探究进气道整流罩打开过程中内流场的演化规律,针对下颌式进气道及其配套整流罩,基于重叠网格法求解N-S方程,详细分析了抛罩过程中内流场演化过程与特征流场结构。研究表明,堵罩时,整流罩前端发展出V形激波,整流罩尾部形成后向台阶且产生一对涡矢量方向相反的流向涡,开罩过程中,整流罩前端的V形激波与尾部的后向台阶均会对内流场流动产生影响,捕获流量在中间某时刻达到峰值且大于稳定状态。对于开罩过程流动准定常且内流道无大分离区的流场,进气道在V形激波打在唇口时完成起动且整流罩在此后不影响内流场流动。假设的匀加速转动与重构出的真实转动吻合较好,对于更精确的运动过程模拟可采用三次函数的角速度变化律。     

三维侧压高超声速进气道不启动流场试验与数值模拟研究

对某构型三维侧压高超声速进气道开展了Ma4的自由射流试验和数值仿真,研究 了低马赫数下不启动流场的流动机理。观测到了具有“对涡”结构的底板油流图案,并得到 了分离区的范围和内部流动特征。分析得出,“对涡”结构油流图案和流场中部分离区的形 成是唇口激波和内收缩形成的逆压梯度作用于侧板激波形成的流场中部低能流区的结果。根 据试验和数值模拟结果给出了流场结构示意图,并为下一步进气道构形设计和性能改善工作 提出了建议。     

内并联式TBCC进气道模态转换过程流动特性分析

针对组合动力(TBCC)进气道模态转换过程中出现的非定常气动现象,采用稳态/非稳态数值模拟方法对相关流动特性及其影响因素与流动机理开展了研究。结果表明：由涡轮发动机工作状态向冲压发动机工作模态转换过程中,进气道内出现结尾激波沿流向前后振荡现象,振荡频率约为130Hz;当冲压流道反压引起的激波未前传至模态转换分流板前时,冲压发动机工作状态对结尾激波振荡不产生影响。在相同的发动机工作状态下,随着模态转换速度的增加,结尾激波振荡频率逐渐增大。文中研究的进气道内结尾激波振荡现象可通过亚声速管道内波的传播理论进行解释和分析。     

A novel approach for predicting inlet pressure of aircraft hydraulic pumps under transient conditions

Cavitation caused by insufficient suction is a major factor that influences the life of aircraft pumps. Currently, pressurizing the tank can solve the cavitation problem under steady large-flow conditions. However, this method is not always effective under transient conditions (from zero flow to full flow in a very short time). Moreover, to apply and design other measures, such as a boost impeller, the suction dynamics during the transient period must be investigated. In this paper, a novel approach based on the pressure wave propagation theory is proposed for predicting the inlet pressure of an aircraft pump under transient conditions. First, a dynamic model of a typical aircraft pump is established in the form of differential equations. Then, the transient flow model of the inlet line is described using momentum and continuity equations, and the governing equations are discretized by the method of characteristics and the finite difference method. The simulated results are in good agreement with the results from verification tests. Further simulation analysis indicates that the wave velocity and transient time may influence the inlet and reservoir pressure as well as the size of the inlet line. Finally, solutions for upgrading the inlet pressure are discussed. These solutions provide guidelines for designing inlet installations.     

槽对超声速混压式进气道性能及附面层的影响

为了提高定几何超 声速混压式轴对称进气道的性能，应用在进气道不同位置开槽的方法 ，研究了在各级锥体上、锥体的折角处开槽时锥体上的附面层变化；研究了多工况下开槽对进气道的总压恢复系数、流量系数、冲压比和起动性能产生的影响。结果表明开槽将改变超声速进气道头锥上的波系分布，使槽后附面层厚度增加。折角处开槽槽后附面层厚度比原型进气道增加16.7%，锥体上开槽比原型进气道增加33.3%。开槽使高马赫数下的总压恢复系数有所增加，其增加量随来流马赫数的变化而变化。在马赫数为4.0的设计状态下，折角处开槽可使进气道的总压恢复系数提高1.8%，锥体上开槽可以提高4.3%。之外，锥体折角处开槽对流量系数影响不大，还可以改善进气道的起动性能，降低起动马赫数。     

冲压增程弹丸进气道特性分析

采用块结构网格与二阶精度流场分区求解技术，对固体火箭冲压发动机增程弹丸超声速进气道特性进行了深入研究。通过数值模拟得到了对应于不同来流马赫数和攻角情况下，临界工况时，超声速进气道内外粘性流场复杂的波系结构，详细分析了来流马赫数和攻角对进气道性能的影响。结果显示，随着来流马赫数的增大，总压恢复系数显著降低，流量系数增大，同时随着来流攻角的增大，总压恢复系数及流量系数逐渐降低，而流场畸变指数则明显增大。