内装式空射运载火箭重力出舱机箭耦合动力学分析

研究了以运输机为平台的内装式运载火箭空射过程载机和火箭的耦合动力学建模。建模针对两个阶段：第一阶段，火箭固定于载机机舱内，两者构成一个整体，按照普通刚体的力学方法处理；第二阶段，火箭解锁后，沿着舱内的发射筒向外滑行，载机和火箭形成两刚体相互作用的耦合系统，基于牛顿-欧拉法建立系统动力学模型。载机在空射火箭过程中，油门和升降舵满偏，在加速前飞的同时拉大姿态俯仰角，火箭在自身重力分量和惯性力的作用下，沿着机舱内的发射筒加速向外滑行，直至与载机分离。数值仿真分析了空射过程载机的重要力学参数的变化过程，验证了载机操控策略的可行性和安全性，可为未来中国空射运载火箭技术设计提供数据参考。     

Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

涡轮基组合循环发动机分布式控制系统通信网络混合拓扑结构优化方法

涡轮机组合循环(Turbine based combined cycle,TBCC)发动机控制系统通信网络拓扑结构是其分布式控制系统方案设计的重要部分,优化网络拓扑结构可提高发动机推重比和控制系统可靠性。本文基于智能优化算法提出TBCC分布式控制系统网络拓扑结构优化方法。基于图论建立TBCC几何模型和网格模型,以重量和可靠性为优化性能指标,同时考虑发动机表面高温区域以及控制节点的工作可靠性,分别采用粒子群算法和遗传算法优化星形结构中智能中央节点位置、中央节点的环形拓扑结构,获得星形-环形混合拓扑结构。仿真实例表明,基于本文方法优化所得的混合拓扑结构相较于星形集中式控制结构,系统重量降低了51.9%。     

An innovative approach for integrated airline network and aircraft family optimization

The determination of optimal aerial transport networks and their associated flight frequencies is crucial for the strategic planning of airlines, as well as for carrying out market research, to establish target markets, and for aircraft and crew rostering. In addition, optimum airplane types for the selected networks are crucial to improve revenue and to provide reduced operating costs. The present study proposes an innovative approach to determine the optimal aerial transport network simultaneously with the determination of the optimum fleet for that network, composed of three types of airplanes (network and vehicle integrated design). The network profit is maximized. The passenger’s demands between the airports are determined via a gravitational model. An embedded linear programming solution is responsible for obtaining potential optimal network configurations. The optimum fleet combination is determined from a database of candidate aircraft designs via genetic algorithm. A truly realistic airplane representation is made possible thanks to accurate surrogate models for engine and aerodynamics is adopted. An accurate engine deck encompassing a compression map and an innovative engine weight calculation besides an aerodynamical artificial neural network module enable a high degree of accuracy for the mission analysis. The proposed methodology is applied to obtain the optimum network comprised of twenty main Brazilian airports and corresponding fleet.     

一种飞机大仰角飞行的模糊控制方法

提出了一种飞机大仰角飞行的动态逆模糊集成控制方法。首先使用动态逆方法求得系统的逆，使系统反馈线性化，然后，用具有在线规则自调整的模糊控制方法来确保系统的最终特性。该方法应用在高性能收音机俯仰机动指令系统的设计中，仿真结果表明，所设计的控制器满足操纵品质的要求，并且，在大仰角飞行时具有较好的鲁棒性。     

自由飞试验模型惯性矩的测定

作者根据多年来自由飞试验的实践,叙述了自由飞模型惯性矩的调试、计算、误差分析与处理的经验与方法。     

关于疲劳裂纹扩展数学模型的参数寻优

本文通过引入工程设计中的优化方法，分别对室内空气环境下铝合金（ＬＹ１２－ＣＺ）材料疲劳裂纹扩展的数学模型，以及环境条件下（３．５％ＮａＣｌ水溶液浸泡）该材料腐蚀疲劳裂纹扩展的数学模型进行了探讨。在已知标准试样在不同的环境下疲劳裂纹扩展实验ｄａｄＮｉ，ΔＫｉ的条件下，采用优化方法进行参数寻优，可方便地得到与其对应的疲劳裂纹扩展的ｄａｄＮ～ΔＫ最优数学模型     

飞行末区目标可攻击性算法研究

分析了飞行器飞行末区存在的各种约束条件及其对飞行器飞行的影响，用最大爬升（下滑）半径约束法来代替过载约束进行飞行器纵向机动飞行的高度控制，并给出了在诸多约束条件下目标可攻击性的算法。最后利用等高线地形图进行了仿真验证，结果表明，该算法满足诸多约束要求，可用于工程应用。     

J—7LP飞机1：6遥控模型失速尾旋试验

对无动力J—7LP动力学缩比模型进行了遥控试飞,以研究其失速尾旋特性,全偏平尾和方向舵可使模型进八尾旋,舵面全回中即可从各种尾旋中改出。偏转副翼对尾旋特性有明显的影响。     

满足约束的Gn连续过渡曲面的构造

在Erich Hartmann提出的由两基曲面线性组合构造G^n连续过渡曲面方法的基础上，针对该方法存在很难找到合适的参数变换的问题，提出了一种基于基曲面局部区域重新参数化构造G^n连续过渡曲面的方法。通过对基曲面上切触线附近区域部分曲面重新参数化，再由重新参数化局部基曲面线性组合构造G^n连续过渡曲面。这样将两基曲面间构造过渡曲面的问题转化为在重新参数化局部基曲面间构造过渡曲面。以构造G^1连续的翼身融合面为例，讨论了满足约束要求条件时G^2连续过渡面的构造方法。即先对基曲面上过渡切触线附近的局部区域进行重新参数化，后通过优化求解来确定比例因子和偏移量、平衡因子和调配因子，使过渡曲面满足前后边条线约束，最后利用线性组合来构造G^2连续的过渡面。约束过渡曲面的形状可通过改变重新参数化基曲面的大小来调整．