内装式空射运载火箭重力出舱机箭耦合动力学分析

研究了以运输机为平台的内装式运载火箭空射过程载机和火箭的耦合动力学建模。建模针对两个阶段：第一阶段，火箭固定于载机机舱内，两者构成一个整体，按照普通刚体的力学方法处理；第二阶段，火箭解锁后，沿着舱内的发射筒向外滑行，载机和火箭形成两刚体相互作用的耦合系统，基于牛顿-欧拉法建立系统动力学模型。载机在空射火箭过程中，油门和升降舵满偏，在加速前飞的同时拉大姿态俯仰角，火箭在自身重力分量和惯性力的作用下，沿着机舱内的发射筒加速向外滑行，直至与载机分离。数值仿真分析了空射过程载机的重要力学参数的变化过程，验证了载机操控策略的可行性和安全性，可为未来中国空射运载火箭技术设计提供数据参考。     

Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

机载托架自动校准系统的设计与实现

为了解决机载托架传统校准方法精度低、耗时、费力等问题,设计了一种高精度、高效率并且操作简单的成品托架自动校准系统。该系统运用调平精度较高的"循环多次"最高点不动调平方法,建立高精度机载托架校准的静力学数学模型,运用VC与Matlab的COM接口编程技术开发机载托架自动校准系统,并建立良好的人机交互界面。试验结果表明,利用该方法对机载托架进行校准,无论是校准精度还是校准效率都较传统方法有很大提高。     

轨控大干扰下的系统角动量管理

摘要： 针对利用角动量交换装置系统实现轨控期间姿态维持的情况，研究当轨控推力器存在大力矩扰动时系统角动量管理方法.结合对地运行航天器轨道运动特性，分析轨控干扰力矩的积累角动量变化规律；考虑角动量管理装置系统的角动量存贮容量，基于角动量积累规律提出了一种结合偏置角动量建立与对称分布轨控位置选择的系统角动量管理方法，实现了对称轨控位置积累角动量互相抵消的自平衡效果，极大程度地提高轨控效率且避免系统角动量饱和现象.所提出的方法适用于喷气欠驱动控制系统，方法的有效性通过了数学仿真验证及在轨型号应用.     

部署retro-GEO巡视器的月球借力飞行轨道分析

retro-GEO是指逆行（retrograde）地球静止轨道（geostationary Earth orbit, GEO），该轨道与GEO轨道高度相同或相近，但倾角为180°，安装在retro-GEO卫星上的巡视器可每12h对GEO带空间资产附近碎片环境安全预警。直接西向发射retro-GEO卫星存在地面测控和发射能耗较大的困难。基于平面四体模型，为降低设计变量敏感性，以近月点参数为设计变量，建立了部署retro-GEO巡视器的月球借力飞行轨道设计模型，利用轨道动力学模型延拓策略，得到该类轨道绕月后返回地球飞行时长只能约为114.79h，该结论可用于求解该类轨道高精度轨道动力学模型解。     

An improved numerical method for constructing Halo/Lissajous orbits in a full solar system model

An improved numerical method that can construct Halo/Lissajous orbits in the vicinity of collinear libration points in a full solar system model is investigated. A full solar system gravitational model in the geocentric rotating coordinate system with a clear presentation of the angular velocity relative to the inertial coordinate system is proposed. An alternative way to determine patch points in the multiple shooting method is provided based on a dynamical analysis with Poincare′sections. By employing the new patch points and sequential quadratic programming, Halo orbits for L_1, L_2, and L_3 points as well as Lissajous orbits for L_1 and L_2 points in the EarthMoon system are generated with the proposed full solar system gravitational model to verify the effectiveness of the proposed method.     

椭圆轨道卫星对地全球覆盖电推进控制

针对椭圆轨道卫星近/远地点的星下点对全球或特定纬度区域的访问问题，提出一种连续小推力下的对地覆盖控制策略。首先，推导了自然摄动对卫星拱线变化的影响，并探讨了进行小推力覆盖控制的必要性。然后，针对燃料消耗的优化问题，将控制方程展开成含傅里叶级数的形式，用以获得便于星上计算的解析形式的次优解，同时探讨了截取阶数与优化程度的关系。在进行拱线控制的同时，通过合理设置约束，对椭圆轨道的近地点高度进行保护，确保卫星安全运行。仿真结果表明，提出的方法能够以适当的燃料消耗代价实现椭圆轨道的近/远地点的全球覆盖控制或特定纬度区域的反复推扫，且控制力在可接受的范围内。     

AP聚类改进免疫算法用于航空发动机故障诊断

在免疫算法训练过程中引入近邻传播(AP)聚类与熵权法,对训练样本进行聚类与权值计算,将权值引入免疫算法中样本选择阈值的计算,以解决训练过程采用固定选择阈值所造成的检测器在部分区域过拟合,部分区域欠拟合的问题。结果表明:改进的免疫算法用于典型非线性函数的寻优时,迭代性能均优于传统免疫算法,并在大部分情况下优于粒子群算法与量子遗传算法,在进行某型发动机故障诊断的实例实验时,改进后的算法的诊断准确率达到98.06%,高于传统免疫算法的92.60%。      

多臂空间机器人的视觉伺服与协调控制

针对多臂空间机器人自主目标抓捕任务，首先建立多臂空间机器人的运动模型和其与目标的相对运动模型，采用Kane方法建立多臂空间机器人的动力学模型；其次，研究基于视觉伺服的机械臂在线轨迹规划算法，并引入零反作用机动，消除机械臂运动对平台姿态的扰动；再次，在不使用零反作用机动功能时，分别使用基于角动量前馈补偿的协调控制算法和逆动力学方法设计了协调控制器，在机械臂运动时保持平台姿态和相对目标的位置。最后，开发了基于Matlab的仿真软件MASS（多臂空间机器人仿真），仿真结果校验了上述方法的有效性。