A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

一种基于VPL 的元器件快速建模方法

为了更好地落实航空电子模块的可制造性设计审查工作,结合航空电子模块产品特点和技术要求,建设了基于Valor软件的PCB/PCBA设计与检测自动化分析系统.元器件模型库作为该系统的必要组成部分,其覆盖范围和数据精度对审查结果至关重要.本文将从元器件模型库建设必要性、建设过程和建模工艺要求三个方面进行阐述,并提出一种基于Valor VPL的元器件快速建模方法,应用结果表明,该方法能够高效构建满足系统审查精度的元器件模型,使大规模元器件模型库的建设成为可能.     

Orbital stability close to asteroid 624 Hektor using the polyhedral model

We investigate the orbital stability close to the unique L4-point Jupiter binary Trojan asteroid 624 Hektor. The gravitational potential of 624 Hektor is calculated using the polyhedron model with observational data of 2038 faces and 1021 vertexes. Previous studies have presented three different density values for 624 Hektor. The equilibrium points in the gravitational potential of 624 Hektor with different density values have been studied in detail. There are five equilibrium points in the gravitational potential of 624 Hektor no matter the density value. The positions, Jacobian, eigenvalues, topological cases, stability, as well as the Hessian matrix of the equilibrium points are investigated. For the three different density values the number, topological cases, and the stability of the equilibrium points with different density values are the same. However, the positions of the equilibrium points vary with the density value of the asteroid 624 Hektor. The outer equilibrium points move away from the asteroid’s mass center when the density increases, and the inner equilibrium point moves close to the asteroid’s mass center when the density increases. There exist unstable periodic orbits near the surface of 624 Hektor. We calculated an orbit near the primary’s equatorial plane of this binary Trojan asteroid; the results indicate that the orbit remains stable after 28.8375?d.     

基于相对最值点的最小二乘直线检测方法

为了解决传统目标检测中遇到的检测速度慢、精度低等问题，本文提出一种新的图像特征——相对最值点，并依据相对最值点提出一种新的最小二乘直线检测的方法。该方法首先搜索Canny边缘的闭合包络，并寻找闭合包络的相对最值点。包络上相邻相对最值点之间长度满足阈值要求的即为疑似直线的两端点，进而利用最小二乘拟合方法获得该疑似直线的拟合方差，最后利用拟合方差与拟合直线长度之比作为直线判定的标准用来检测出图像中的直线。实验表明，本方法与传统方法如PPHT直线检测、LSD直线检测方法等相比，检测直线的精度更高，检测速度更快。     

空间推进器制造中的可破坏性工装

由于航天研究的特殊性,其预研型号零件一般批量很小,并且有许多零件不易装夹。选用一种不同于传统专用工装的可破坏性工装,其材料可以是金属的,也可以是非金属的。为保证进度,必须建立预先性的可破坏性工装的数据库。采用可破坏性工装缩短了研制周期,降低了研制成本。     

最坏风模型及对飞机突防航迹跟踪的影响

针对一类非线性动力学系统,本文推导出二次型性能指标下的微分对策解,由此得到一组含有非线性因素的最环风模型,这一模型特别适用于研究作空间机动飞行的飞机受外界环境扰动的灵敏性问题。最后考察了这一变化风场对飞机突防航迹非线性解耦跟踪的影响。     

关于Nielsen数的注记

通过构造基本群的正规子群，得到有限复迭空间和自映射的提升。并定义了NL数，指出用NL数可以估算自映射的Nielsen数。     

400kN振动台承力钢架的研制

文章中介绍的400kN 承力钢架是用来作船罩联合试验的承力机构,具有结构庞大、复杂的特点,对自振频率有一定要求,文章介绍了该设备研制过程中的设计、计算、加工及安装工艺技术等。     

基于高频导纳原理的液位传感器

介绍一种新型液位传感器。分析传统电容液位传感器在实用中的局限性,提出一种防挂料原理,变传统的单纯测量探头电容变化为测量在液位变化下探头的复阻抗的变化,并利用同步整流技术,抵消导电介质挂料造成的虚假信号。设计上,通过合理选取有关参数,避免了信号变换器和探头分置时分布电容的影响,使传感器可以用在高温介质测量场合。     

飞机强度试飞活动部件残余变形分析

试飞中，飞机残余变形测量结果分析主要是判别所测残余变形是否为危及飞行安全、有碍操纵等的有害变形。而飞机活动部件残余变形实测结果常常超差的一个重要原因，是实际测量中，部件所处的状态与图纸要求的差异（存在偏度）。对此提出了偏度修正法和空间基准面修正法，并利用某型飞机全动平尾残余变形的实测数据，验证了这两种方法的有效性，并就方法的适用性进行了讨论。