内装式空射运载火箭重力出舱机箭耦合动力学分析

研究了以运输机为平台的内装式运载火箭空射过程载机和火箭的耦合动力学建模。建模针对两个阶段：第一阶段，火箭固定于载机机舱内，两者构成一个整体，按照普通刚体的力学方法处理；第二阶段，火箭解锁后，沿着舱内的发射筒向外滑行，载机和火箭形成两刚体相互作用的耦合系统，基于牛顿-欧拉法建立系统动力学模型。载机在空射火箭过程中，油门和升降舵满偏，在加速前飞的同时拉大姿态俯仰角，火箭在自身重力分量和惯性力的作用下，沿着机舱内的发射筒加速向外滑行，直至与载机分离。数值仿真分析了空射过程载机的重要力学参数的变化过程，验证了载机操控策略的可行性和安全性，可为未来中国空射运载火箭技术设计提供数据参考。     

Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

散射对高温气体-碳黑颗粒混合物辐射传输的影响

基于全光谱k分布(Full spectrum k distribution,FSK)模型、MIE理论和有限体积法(Finite volume method,FVM),构建了均温、均质辐射参与性气体-碳黑颗粒混合物介质热辐射传输模型,并分析了碳黑不同尺寸、不同体积浓度以及介质不同路径长度和不同温度条件下,因忽略碳黑颗粒散射所导致的介质热辐射传输特性(如辐射热流、辐射源项)的计算误差。研究结果表明:体积分数不变,增大粒径,计算误差呈现出先增大后减小的趋势;数密度不变,增大粒径,或者粒径不变,增大体积分数,均将使得计算误差相应增大;粒径、体积分数不变,增大路径长度,或者升高介质温度,均将增大计算误差。通常对于含有大颗粒、高碳黑浓度的辐射参与性气体-碳黑颗粒混合物介质,碳黑颗粒散射不能忽略。     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

机载托架自动校准系统的设计与实现

为了解决机载托架传统校准方法精度低、耗时、费力等问题,设计了一种高精度、高效率并且操作简单的成品托架自动校准系统。该系统运用调平精度较高的"循环多次"最高点不动调平方法,建立高精度机载托架校准的静力学数学模型,运用VC与Matlab的COM接口编程技术开发机载托架自动校准系统,并建立良好的人机交互界面。试验结果表明,利用该方法对机载托架进行校准,无论是校准精度还是校准效率都较传统方法有很大提高。     

R141b在圆形微通道内的沸腾换热实验研究

为提高换热强度、解决设备内部高热流密度散热问题,采用实验方法研究R141b在不同直径(D=0.5mm和1.0mm)水平圆形微通道内的沸腾换热特性,分析了热流密度(q=2.0kW/m~2～47.6kW/m~2)、质量干度(x=0～0.6)、质量流速(G=111.11kg/(m~2·s)～333.33kg/(m~2·s))的变化对平均传热系数h的影响,探究不同情况下影响沸腾换热的主导因素。实验研究表明:平均传热系数h随热流密度q的增加而减小,在不同范围内减小速率有明显差异;热流密度q=2kW/m~2～5kW/m~2时质量流速G对平均传热系数h影响较明显,热流密度较高时质量流速G对换热影响很小;在质量流速G=111.11kg/(m~2·s)～333.33kg/(m~2·s),质量干度x0.3时,平均传热系数h随质量干度x增加而明显下降,在设计微通道换热器时应尽量使R141b处于初始沸腾阶段以获得更好换热效果,并采取一定措施预防干度过高引起的换热恶化。     

AP聚类改进免疫算法用于航空发动机故障诊断

在免疫算法训练过程中引入近邻传播(AP)聚类与熵权法,对训练样本进行聚类与权值计算,将权值引入免疫算法中样本选择阈值的计算,以解决训练过程采用固定选择阈值所造成的检测器在部分区域过拟合,部分区域欠拟合的问题。结果表明:改进的免疫算法用于典型非线性函数的寻优时,迭代性能均优于传统免疫算法,并在大部分情况下优于粒子群算法与量子遗传算法,在进行某型发动机故障诊断的实例实验时,改进后的算法的诊断准确率达到98.06%,高于传统免疫算法的92.60%。      

多臂空间机器人的视觉伺服与协调控制

针对多臂空间机器人自主目标抓捕任务，首先建立多臂空间机器人的运动模型和其与目标的相对运动模型，采用Kane方法建立多臂空间机器人的动力学模型；其次，研究基于视觉伺服的机械臂在线轨迹规划算法，并引入零反作用机动，消除机械臂运动对平台姿态的扰动；再次，在不使用零反作用机动功能时，分别使用基于角动量前馈补偿的协调控制算法和逆动力学方法设计了协调控制器，在机械臂运动时保持平台姿态和相对目标的位置。最后，开发了基于Matlab的仿真软件MASS（多臂空间机器人仿真），仿真结果校验了上述方法的有效性。     

运载火箭推进剂复杂流动传热问题数值模拟中的模型简化方法

在运载火箭改进优化或新型运载火箭设计过程中,会遇到各种复杂的流动与传热问题。按照真实产品和物理过程直接建立的数值计算模型过于复杂,不同尺度的结构、流动与传热、长时间的飞行过程相互耦合,出现计算时间太长(数年)、收敛困难、程序调试困难等问题。针对初始条件复杂、飞行过程复杂、边界条件复杂3类具体问题,总结了3种相应的模型简化方法,分别是工程经验法、极限参数法、低维近似法,为推进剂复杂流动与传热的数值模拟提供参考。     

基于变马赫数的五孔探针三维插值方法

探讨了五孔探针气动数据的插值方法,为提高插值精度,开发了基于传统线性插值法的三维线性插值法。该方法把同一探针在不同马赫数下的校准图形成三维数据库,将实验数据通过三维图进行插值。并使用改进前后的两种插值方法分别对校准风洞测得的数据进行整理,对比结果证明:在实验工况连续变化的情况下,三维线性插值法在插值精度上要优于传统线性插值法。特别是在来流马赫数变化较大时,该方法可以改善单一校准文件处理造成的数据精度问题,可用于自动化流场采集系统,为流场高速高精度采集奠定基础。