A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

导流锥结构参数对燃气弹射筒内压力冲击平滑效果影响研究

针对导流锥结构参数对内弹道流场耦合影响问题，基于动态分层动网格技术，构建了含导弹运动和二次燃烧的内弹道数值模型，并验证了模型可靠性。解耦分析了导流锥半径、高度及冲击高度对内弹道流场特性和载荷的影响。结果表明：导流锥的结构直接决定燃气飞溅现象的产生和流场结构的紊乱程度，导流锥的半径、高度和冲击高度的改变会对燃气反射点的位置、二次燃烧的区域以及剧烈程度产生影响;结构优化后的导流锥，较大程度地缓解了冲击现象，获得了较好的平滑效果，筒底压力较实验装置降低了24.5%。     

夹杂物特征参数对拉伸载荷下超高强度钢裂纹萌生与扩展的影响

采用扫描电镜原位观测的方法,动态跟踪观察拉伸载荷作用下航空发动机轴类超高强度钢MA250中不同形状和尺寸的TiN夹杂导致裂纹萌生与扩展的微观行为,从微观角度分析拉伸载荷作用下夹杂物的几何长轴与外加载荷方向成不同角度时裂纹的萌生方式.同时讨论TiN夹杂中第一条裂纹萌生所需的应力与夹杂物面积的关系.结果表明,夹杂物面积越大,第一条裂纹萌生所需的应力越小.     

Ionospheric behavior of the F2 peak parameters foF2 and hmF2 at Hainan and comparisons with IRI model predictions

Monthly median values of foF2, hmF2 and M(3000)F2 parameters, with hourly time interval resolution for the diurnal variation, obtained with DPS-4 digisonde observations at Hainan (19.4°N, 109.0°E) are used to study the low latitude ionospheric variation behavior. The observational results are compared with the International Reference Ionospheric Model (IRI) predictions. The time period coverage of the data used for the present study is from March 2002 to February 2005. Our present study showed that: (1) In general, IRI predictions using CCIR and URSI coefficients follow well the diurnal and seasonal variation patterns of the experimental values of foF2. However, CCIR foF2 and URSI foF2 IRI predictions systematically underestimate the observed results during most time period of the day, with the percentage difference ΔfoF2 (%) values changing between about −5% and −25%, whereas for a few hours around pre-sunrise, the IRI predictions generally overestimate the observational ones with ΔfoF2 (%) sometimes reaching as large as ∼30%. The agreement between the IRI results and the observational ones is better for the year 2002 than for the other years. The best agreement between the IRI results and the observational ones is obtained in summer when using URSI coefficients, with the seasonal average values of ΔfoF2 (%) being within the limits of ±10%. (2) In general, the IRI predicted hmF2 values using CCIR M(3000)F2 option shows a poor agreement with the observational results. However, when using the measured M(3000)F2 as input, the diurnal variation pattern of hmF2 given by IRI2001 has a much better agreement with the observational one with the detailed fine structures including the pre-sunrise and post-sunset peaks reproduced reasonably well. The agreement between the IRI predicted hmF2 values using CCIR M(30,000)F2 option and the observational ones is worst for the afternoon to post-midnight hours for the high solar activity year 2002. During daytime hours the agreement between the hmF2 values obtained with CCIR M(30,000)F2 option and the observational ones is best for summer season. The discrepancy between the observational hmF2 and that obtained with CCIR M(30,000)F2 option stem from the CCIR M(3000)F2 model, which does not produce the small scale structures observed in the measured M(3000)F2.     

尺寸参数对气动液阀启动特性的影响

为气动液阀的启动过程建立了数学模型，分析了尺寸参数对该阀启动特性的影响。计算结果表明：在保证必要的工作寿命的前提下，适当地增大控制腔气孔的直径或增大靠近控制腔的活塞端面直径有利于提高该阀的响应能力。本文所得的结论有利于此类阀门的设计。     

Xilinx SRAM型FPGA抗辐射设计技术研究

针对Xilinx SRAM型FPGA在空间应用中的可行性，分析了Xilinx SRAM型FPGA的结构，以及空间辐射效应对这种结构FPGA的影响，指出SRAM型的FPGA随着工艺水平的提高、器件规模的增大和核电压的降低，抗总剂量效应不断提高，抵抗单粒子效应，尤其是单粒子翻转和单粒子瞬态脉冲的能力降低。分析了FPGA综合后常见的Half-latch在辐射环境中的影响并结合实际工程实践给出了解决上述问题的一些有用办法和注意事项，如，冗余设计、同步设计、算术逻辑运算结果校验、白检等。最后还提出一种基于COTS器件的“由顶到底”的星载信号处理平台结构，分析了这种结构在抵抗辐射效应时的优势。有关FPGA抗辐射的可靠性设计方法已经在某卫星通信载道中成功应用，并通过了各种卫星环境试验，该技术可以为有关航天电子设备设计提供参考。     

固体火箭发动机试验模态分析技术研究

将固体火箭发动机划分为144个自由度，采用锤击法，单点激励多点响应（SIMO）对其在4种工况下进行了频率响应的测量，应用了多种方法进行模态参数识别和数据拟合，并对其结果进行比较，获得了发动机在各工况1kHz以内的各阶固有频率、振型和阻尼，并对试验模态分析技术在固体火箭发动机试验中的应用进行了研究。     

浮栅ROM器件的质子辐射效应实验研究

给出了浮栅ROM器件的质子辐射效应实验结果.认为浮栅ROM28C256和29C256的质子辐射效应不是单粒子效应,而是质子及其次级带电粒子产生的累积剂量造成的总剂量效应.器件出现错误有个质子注量阈值.对于29C256,高温加电退火容易消除质子产生的辐射损伤;对于28C256,高温加电退火不易消除质子产生的辐射损伤.动态监测和静态加电的器件都出现数据错误,且不能用编程器重新写入数据.然而不加电的器件在更高的质子注量辐照下未出现错误.对于应用浮栅ROM器件的航天器电子系统,冷备份是提高其可靠性的有效手段之一.     

异型封闭腔辐射几何学问题

讨论了解决异型封闭腔辐射几何学问题的几种方法:异型封闭腔内,表面间可见性的判断方法;优化异型封闭腔角系数计算的方法;确定异型封闭腔内定向辐射的壁面辐射源的方法.计算了两种结构喷管封闭腔内的角系数,并从角系数的互换性和完整性定理验证了方法的正确性和有效性,为异型封闭腔的辐射计算解决了几何问题.     

The fundamental parameters of the central stars of eight WR ring nebulae

We describe work that has recently been completed on deriving the fundamental parameters of eight WR stars through the photoionization modelling of their surrounding nebulae using non-LTE WR flux distributions. The resulting effective temperatures range from 57 000–71 000 K for the WN4-5 stars and <30 000–42 000 K for the WN6-8 stars. The derived stellar parameters are compared with those obtained from stellar emission line modelling. We find good agreement for the hot early WN stars, indicating that the non-LTE WR flux distributions have essentially the correct shape in the crucial far-UV region. We find lower temperatures for the four cooler late WN stars, particularly for the two WN6 stars. For the nebulae surrounding these stars, we find that the model flux distributions produce too much nebular ionization. We suggest that these discrepancies arise because of the lack of line-blanketing in the WR atmospheres. For the WO1 central star of G2.4+1.4, with strong nebular He II 4686 A emission, we derive a temperature of 105 000 K, somewhat less than previous estimates. The positions of our eight WR stars on the H-R diagram are compared with the evolutionary tracks of Maeder (1990) for solar metallicity. In common with previous workers, we find that our derived luminosities are too low, giving an initial mass range of 25–40 M, below that expected for the majority of WR stars.