Multi-faults diagnosis of rolling bearings via adaptive customization of flexible analytical wavelet bases

Multi-faults detection is a challenge for rolling bearings due to the mode mixture and coupling of multiple fault features, as well as its easy burying in the complex, non-stationary structural vibrations and strong background noises. In this paper, a method based on the flexible analytical wavelet transform (FAWT) possessing fractional scaling and translation factors is proposed to identify multiple faults occurred in different components of rolling bearings. During the route of the proposed method, the proper FAWT bases are constructed via genetic optimization algorithm (GA) based on maximizing the spectral correlated kurtosis (SCK) which is firstly presented and proved to be efficient and effective in indicating interested fault mode. Via using the customized FAWT bases for each interested fault mode, the original vibration measurements are decomposed into fine frequency subbands, and the sensitive subband which enhances the signal-to-noise ratio (SNR) is selected to exhibit the fault signature on its envelope spectrum. The proposed method is tested via simulated signals, and applied to analyze the experimental vibration measurements from the running roller bearings subjected to outrace, inner-race and roller defects. The analysis results validate the effectiveness of the proposed method in identifying multi-faults occurred in different components of rolling bearings.     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

星载激光通信终端在轨机动对温度影响

对激光通信终端在轨瞬态温度变化开展了仿真，以期研究在轨机动的影响、热分析和热试验时机动模式的简化模拟。通过合理地分析与简化，建立终端的轨道热分析模型，准确模拟在轨机动，根据典型机动模式、外热流和涂层退化等因素设计了计算工况，得出了终端在轨运行过程中的温度场随时间和姿态变化规律。结果表明：不同机动模式下的温度变化存在差异，最大可达23.0℃，采用固定姿态或一维转动的简化热分析或热试验不能准确模拟实际飞行温度，甚至不能部分替代二维转动热分析或热试验；光学天线和反射镜的温度控制是制约终端工作的瓶颈，为终端设计合适的避光机动策略，可大幅度提高温度稳定度和均匀度。研究结果可以为光机电设备在轨机动策略的设计和改进提供参考。     

含有任意多个椭圆孔弹性板的应力场计算

本文应用弹性力学的复变函数理论,用多保角变换的方法,导出了含有任意多个椭圆孔的无限大弹性板多复变量应力函数的表达式。每个孔的大小、位置和孔边作用的载荷均为任意指定。板的无限远处作用有和坐标轴方向一致的均匀拉压载荷P_x,P_y和均匀剪切载荷P_(xy)。并在孔边进行复Fourier级数展开,用待定系数法确定应力函数的未知系数,从而计算弹性板的应力场。编制了相应的FORTRAN77标准化程序,进行了考题和算例分析,给出了级数的收敛状况和孔边周向应力的分布图。     

利用热源温度场迭加法诊断持续点热源的强度及位置

可重复使用运载器的防热瓦故障会使航天器的局部结构产牛热源，并在结构中形成温度场。应用热源温度场迭加法的解函数，解得结构温度历程，然后据此温度的变化率趋势判断出热源位置，在此基础上依据多点测最值构造出辨识参数用于热强度识别，通过对一薄壁结构模型算例的计算仿真，证明了本文所提方法的有效性。论文工作为进一步开展热源诊断技术研究，提供了可资工程实践应用的数值算法体系以及有益的数值计算结论。     

普郎克定律的一个新推论

根据热辐射基本定律———普郎克定律,推导出了一个新的推论。即对于任意温度T的黑体辐射源,总存在一对应波长λδ,该波长对应的黑体单色辐射亮度对温度T的偏导数最大,且λδT =2 4 10 .3μm·K。这一结论对于单波长辐射温度计设计中探测器波段的选择有重要参考价值,根据此结论可以推出温度测量灵敏度最高的波长。     

燃烧催化剂苯甲酸铜盐及其衍生物的热分解研究(Ⅱ)──双取代基苯甲酸铜盐的热分解机理

羟基氨基苯甲酸铜、二羟基苯甲酸铜、二硝基苯甲酸铜和对硝基苯甲酸铜的DSC和TG热分解研究表明，与苯甲酸铜一样，它们分解都生成一种稳定的二聚作中间产物──双核铜五元环络合物，前二者还能生成一种八元环二聚体络合物。芳香基上由于引入硝基，使主要分解反应阶段由吸热效应变成放热反应，具有二个硝基取代基者，这种放热效应较只有一个硝基者更强烈。本文还初步探讨了苯甲酸铜及其衍生物分解历程与双基推进剂燃烧过程催化效果的关系。     

基于磁场映像的印制电路板故障诊断方法研究

简要分析了印制电路板的电磁场，提出了用电磁感应法测量磁场的电咱故障诊断新方法，并给出了测试系统组成方案。最后通过验证实验证明了该方法是确实可行的。     

历经十年寿命试验的消旋天线机构轴承的可靠性分析

解决了一个计算可靠性问题的特例。分析了消旋天线机构轴承历经10年寿命试验的可靠性问题。并给出了轴承在不同可靠寿命要求下的可靠度(对应不同置信度)。     

求解含多个右端向量非对称线性方程组的自适应块拟最小残量IOM(q)算法

许多实际应用问题需要求解含多个右端向量的大型非对称线性方程组 ,通常是把原来方程组分成单独几个含一个右端向量的方程组 ,再用某种迭代法分别单个求解 ,而更加经济有效的方法是应用能同时产生几个迭代向量的块迭代法来直接求解。本文在 IOM(q)算法的基础上 ,提出一种求解此类方程组的块拟最小残量 IOM(q)算法 ,讨论了如何收缩掉已收敛的部分方程组以及如何从产生的块 Krylov序列中删除线性相关或几乎线性相关向量的自适应技术。数值试验表明 ,此新的自适应块算法比块 GMRES算法及其他相关算法具有更好的收敛行为、更少的计算量和 CPU计算时间 ,是求解此类方程组的一种更加经济有效的算法。