直升机红外抑制器两种进气方式下的实验研究

利用地面模拟试验件通过实验比较分析了两种进气方式对红外抑制器性能的影响。为了模拟直升机前飞和悬停两种状态,在模型上端开口,分别引入旋翼下洗气流和前端进气,对比分析了这两种状态下模型壁面温度和红外辐射强度的大小。结果表明:引入速度为18 m/s的旋翼下洗气流使得模型壁面内外两侧均受到冷却气膜的保护,从而使壁面温度降低了36%;同时再引入流量为0.2 kg/s的前端进气,可使红外抑制器模型在3~5μm和8~14μm的红外辐射强度分别降低为原来的11%和28%。     

叶根间隙泄漏流对跨声压气机转子性能的影响

为研究压气机转子上游叶根轴向间隙泄漏流对转子性能的影响程度以及泄漏流与转子流场之间的相互作用机制,对带有叶根泄漏流的跨声压气机转子流场进行了数值模拟。计算时分别采用了两种模化途径,即耦合求解转子上游叶根间隙内空腔与转子通道内的流场,以及求解将叶根间隙模化为进口边界的转子流场。结果表明:叶根泄漏流可使叶根附近流动堵塞增大,造成转子气动性能的恶化。另外,叶根泄漏流的周向速度分量越大,泄漏流对转子流场的不利影响也越大。     

发动机转子系统早期故障特征提取方法

对飞机发动机转子系统早期故障特点进行分析的基础上,提出了利用虚拟仪器和Matlab小波工具箱分析软件对其早期故障进行检测和特征提取的方法.文中对早期故障特征量的选取、有用信号与噪声信号的分离方法、突变信号与奇异信号的特征提取等进行了分析和研究,并以转子早期碰摩和早期不平衡为例进行了实验研究.结果表明,Labview和Matlab小波分析软件相结合,能够快速有效地提取发动机转子系统的早期故障特征,为发动机转子系统早期故障的快速识别提供了一种新途径.     

航空发动机平衡工艺技术的发展

论述了航空发动机转子平衡技术在国内外的发展状况,重点介绍了刚性转子和柔性转子平衡法及本机平衡法,并对该项技术在国内应如何发展,提出了建议。     

Effect of protrusion amount on gas ingestion of radial rim seal

In this paper, the effect of different amount of protrusion on various parameters in rotor–stator system was experimentally studied by measuring CO₂ concentration and pressure, in order to obtain the optimal protrusion amount. The parameters of different dimensionless sealing flow were measured under the condition that the annulus Reynolds number was 4.39 × 10⁵ and the rotating Reynolds number was 1.05 × 10⁶. The results show that the change of the amount of protrusions has little effect on the static pressure in the cavity, and the static pressure change near the sealing ring is almost negligible. But the total pressure and sealing efficiency increase first and then decrease with the increase of the amount of protrusion. The variation of power consumption is the same. A complex vortex structure will appear at the high radius region when the protrusion is installed. On the other hand, the protrusion can effectively reduce the minimum sealing flow of the rotor–stator cavity. Furthermore, considering the sealing efficiency and power consumption, the best range of the protrusion amount is about 36. The ratio near this range can optimally balance the alleviation of the gas ingestion and the reduction of the power consumption.     

A coupling VWM/CFD/CSD method for rotor airload prediction

A coupling fluid-structure method with a combination of viscous wake model(VWM),computational fluid dynamics(CFD) and comprehensive structural dynamics(CSD) modules is developed in this paper for rotor unsteady airload prediction. The hybrid VWM/CFD solver is employed to model the nonlinear aerodynamic phenomena and complicated rotor wake dynamics;the moderate deflection beam theory is implemented to predict the blade structural deformation; the loose coupling strategy based on the ‘delt method' is used to couple the fluid and structure solvers.Several cases of Helishape 7A rotor are performed first to investigate the effect of elastic deformation on airloads. Then, two challenging forward flight conditions of UH-60 A helicopter rotor are investigated, and the simulated results of wake geometry, chordwise pressure distribution and sectional normal force show excellent agreement with available test data; a comparison with traditional CFD/CSD method is also presented to illustrate the efficiency of the developed method.     

预旋系统稳态和非稳态计算对比研究

针对预旋系统由于旋转引起流场和温度场参数周期性瞬态变化的问题，分别采用滑移网格的瞬态法和固定转子相位的稳态法进行数值求解，并在稳态计算中通过改变转子相位来近似模拟非稳态问题的时空变化特性。通过稳态空间平均结果与非稳态时均结果的对比，以期为预旋系统非稳态问题的低成本求解提供方法依据。结果表明：稳态计算结果与非稳态计算结果相比，周期性波动频率一致，接受孔进口处，稳态计算的压力波动幅度小39%左右，温度波动幅度小15%左右；多个相位的稳态空间平均结果与非稳态时均结果相比，压力高0.2%，温度低0.1%；采用多个计算周期数与单个周期的非稳态计算结果差异微小。当采用喷嘴出口气流中心正对接受孔迎风面前缘的转子相位时，稳态计算结果与非稳态计算时均结果最接近。     

Aerodynamic optimization of rotor airfoil based on multi-layer hierarchical constraint method

Rotor airfoil design is investigated in this paper. There are many difficulties for this high-dimensional multi-objective problem when traditional multi-objective optimization methods are used. Therefore, a multi-layer hierarchical constraint method is proposed by coupling principal component analysis (PCA) dimensionality reduction and e-constraint method to translate the orig-inal high-dimensional problem into a bi-objective problem. This paper selects the main design objectives by conducting PCA to the preliminary solution of original problem with consideration of the priority of design objectives. According to the e-constraint method, the design model is estab-lished by treating the two top-ranking design goals as objective and others as variable constraints. A series of bi-objective Pareto curves will be obtained by changing the variable constraints, and the favorable solution can be obtained by analyzing Pareto curve spectrum. This method is applied to the rotor airfoil design and makes great improvement in aerodynamic performance. It is shown that the method is convenient and efficient, beyond which, it facilitates decision-making of the high-dimensional multi-objective engineering problem.     

燃料分级对旋流火焰的动态特性影响研究

为深入研究分级旋流火焰特性,以分级旋流模型燃烧室为研究对象,对四个不同燃料分级比(Rf)条件下的分级旋流火焰进行了数值研究,在时均燃烧场特性分析的基础上进一步对燃料分级比为1和3两个工况进行了基于壁面建模的大涡模拟(WMLES)研究。结果表明:燃料分级比的改变会影响中心回流区(CRZ)的长度和宽度。燃烧室中截面的散点分布图能够显示出不同燃料分级比条件下的燃烧特征。燃料分级比为1时,燃烧室剪切层仅存在零散的涡破碎区;而燃料分级比为3时,伴随涡破碎区还出现了单螺旋分支进动涡核(PVC)。通过FFT变换获得的燃烧室内剪切层速度能谱主频与进动涡核的旋转频率相同,表明内剪切层速度脉动的产生与进动涡核有关。另外进动涡核会使流场内的燃料分布和燃烧模式发生周期性的变化,进而影响燃烧过程。调整燃料分级比在1附近,能够使分级火焰达到稳定燃烧降低排放的目标。     

Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.