Simulation and Analysis of Electromagnetic Force in Laser Melting Deposition by Electromagnetic Impact

Magnetic field was introduced in laser melting deposition to reduce the pores in workpieces.Finite 3-D model of the coil-deposition layer-substrate was established.Simulation results show that the electromagnetic force in deposition layer mainly concentrates in the projection area of the coil.Axial electromagnetic force shows repulsion in one cycle.The experimental results indicate that the magnetic field is beneficial for grain refinement,microhardness increasement and decline of quantities and average sizes of pores.     

运载火箭交叉输送系统关键影响因素辨识与分析

为深入了解交叉输送系统特性，辨识关键影响因素及其影响规律，通过系统建模与仿真分析开展交叉输送系统关键影响因素研究。推导了交叉输送系统关键组件数学模型，基于AMESim软件构建了系统仿真模型。研究表明，贮箱气枕压差和输送管路流阻是两大关键影响因素。为保证推进剂按额定流量交叉输送，必须对各子级箱压进行精确调节。由于助推上游主管路和交叉输送管路流阻对系统性能影响较大，在设计交叉输送系统时应该尽量缩短助推上游主管路和交叉输送管路，并尽量减小不同助推的管路流阻偏差。     

超临界CO2技术对空心/实心石英混编纤维表面改性

采用热处理+溶剂浸洗+超临界CO2技术对空心/实心石英混编纤维表面进行预处理,同时利用超临界流体的携带与渗透作用,将KH-560偶联剂引入纤维表面进行改性。采用接触角测试、表/界面张力测试、树脂吸附量测试、力学性能测试、扫描电镜等分别测试纤维表面能、胶液表面张力与接触角、胶液与纤维浸润性,观察纤维表面形貌结构,分析复合材料的力学与介电性能。结果表明:采用热处理+溶剂浸洗+超临界CO2技术可有效去除空心/实心石英混编纤维表面浸润剂,提高纤维表面能,促进胶液与纤维的完全浸润,最终改善复合材料力学与介电性能。     

Predicting performance in manually controlled rendezvous and docking through spatial abilities

Manually controlled rendezvous and docking (manual RVD) is a challenging space task for astronauts. This study aims to identify spatial abilities that are critical for accomplishing manual RVD. Based on task analysis, spatial abilities were deduced to be critical for accomplishing manual RVD. 15 Male participants performed manual RVD task simulations and spatial ability tests (the object-manipulation spatial ability and spatial orientation ability). Participants’ performance in the test of visualization of viewpoints (which measures the spatial orientation ability) was found to be significantly correlated with their manual RVD performance, indicating that the spatial orientation ability in the sense of perspective taking is particularly important for accomplishing manual RVD.     

液氢贮箱停放过程中的力热分析

为了寻找到运载火箭长时间停放过程中液氢贮箱的最经济液位，用于制定合理的发射流程以及紧急处置方法，采用计算流体力学(CFD)技术，对某型运载火箭停放期间液氢贮箱的力、热情况进行了仿真计算和分析。计算选用了VOF(Volume-of-fluid)两相流模型以及Lee相变模型，为了提高Lee模型在不同压力情况下对相变过程的模拟精度，采用安托因方程修正了该模型。修正后的模型首先由试验数据校验了其精确性，随后开展的液氢贮箱停放过程仿真结果表明：贮箱的竖直方向与径向均存在温度分层的现象，液相内会形成大的漩涡，该漩涡会使得冷热流体不断进行热交换，并导致贮箱内部的液氢出现气化。贮箱停放期间蒸发率最大值超过2 m 3/h，发生在停放4 h左右；而贮箱液位充填至37 m 3以上或17 m 3以下时蒸发率较低，最小值接近1 m 3/h。     

一种冲击响应谱试验设备校准装置的研制

介绍了冲击响应谱基本概念及其试验设备的分类与工作原理，参考现行冲击试验台检定规程提出了针对该设备的校准方法，设计了一种基于虚拟仪器技术的新型冲击响应谱试验设备校准装置，给出了典型冲击波形（半正弦、矩形、后峰锯齿）的冲击响应谱仿真计算结果并进行了验证，计算结果与理论结果完全一致，证明算法准确可靠，能够实现对冲击响应谱试验设备的校准。     

变循环发动机过渡态性能直接模拟方法

为了实现多变量可调的变循环发动机（VCE）过渡态性能模拟和控制规律设计,在稳态逆算法和过渡态性能隐式格式计算方法的基础上开发了变循环发动机过渡态直接模拟方法。在稳态逆算法模型中加入容积效应和转子动力学方程,实现了同时给定加速率、涡轮前温度和压缩部件工作点的条件下直接模拟计算过渡态过程中变几何参数和燃油流量的调节规律,验证了方法的精度和可行性,并将该方法用于变循环发动机转模态性能模拟和控制规律设计。计算结果表明,过渡态直接模拟方法的误差在0.58%以内,超声速巡航状态下由单外涵模态转换到双外涵模态的时间约为1 s,海平面静止状态下双外涵转单外涵的时间约为3 s,且推力、转速、涡轮前温度、喘振裕度等参数过渡平稳。该方法可简化转模态控制规律设计流程,并提高设计精度。     

端壁抽吸对压气机叶栅间隙泄漏流控制策略的研究

为了研究压气机机匣端壁抽吸对间隙泄漏流动控制的可行性和有效性,以高负荷压气机叶栅为研究对象,通过数值模拟方法对不同抽吸位置和抽吸流量率控制参数下的计算工况进行了对比和分析。研究结果表明:端壁抽吸可以直接地影响叶尖泄漏流的结构形态和存在形式,减弱叶尖泄漏流的强度和影响范围,进而提升压气机叶栅的性能;当抽吸槽覆盖范围包含叶尖泄漏流形成位置及稍靠后附近区域时,所对应的抽吸方案具有较好的控制效果,在0°攻角和0.5%的抽吸流量条件下前槽抽吸和中槽抽吸分别可获得7.04%和7.76%的叶栅总压损失增益;并且进一步研究发现端壁抽吸流量率存在上临界值,应针对不同攻角工况,在其相应的临界值范围内选择合理的抽吸流量,以达到用较小的吸气量实现对间隙泄漏流的控制。     

Determination of optimal samples for robot calibration based on error similarity

Industrial robots are used for automatic drilling and riveting.The absolute position accuracy of an industrial robot is one of the key performance indexes in aircraft assembly,and can be improved through error compensation to meet aircraft assembly requirements.The achievable accuracy and the difficulty of accuracy compensation implementation are closely related to the choice of sampling points.Therefore,based on the error similarity error compensation method,a method for choosing sampling points on a uniform grid is proposed.A simulation is conducted to analyze the influence of the sample point locations on error compensation.In addition,the grid steps of the sampling points are optimized using a statistical analysis method.The method is used to generate grids and optimize the grid steps of a Kuka KR-210 robot.The experimental results show that the method for planning sampling data can be used to effectively optimize the sampling grid.After error compensation,the position accuracy of the robot meets the position accuracy requirements.