Simulation and Analysis of Electromagnetic Force in Laser Melting Deposition by Electromagnetic Impact

Magnetic field was introduced in laser melting deposition to reduce the pores in workpieces.Finite 3-D model of the coil-deposition layer-substrate was established.Simulation results show that the electromagnetic force in deposition layer mainly concentrates in the projection area of the coil.Axial electromagnetic force shows repulsion in one cycle.The experimental results indicate that the magnetic field is beneficial for grain refinement,microhardness increasement and decline of quantities and average sizes of pores.     

Ionospheric F2-Layer critical frequency retrieved from COSMIC radio occultation: A statistical comparison with measurements from a meridional ionosonde chain over Southeast Asia

In this paper, we compared the F2-Layer critical frequency (foF2) derived from FORMOSAT-3/COSMIC radio occultation (RO) and ionosondes at Chiang Mai, Chumphon and Kototabang during the years 2008–2015 to evaluate the performance of COSMIC RO over Southeast Asia region. The results show that the time development of foF2 values derived from COSMIC RO generally agrees well with those from ionosonde measurements. However, the differences between the foF2 derived from COSMIC RO and that derived from ionosonde observations display latitudinal dependence. COSMIC RO tends to underestimate foF2 at Chiang Mai and Kototabang, which is near to the north EIA crest and the south one, respectively, while a little overestimate foF2 at Chumphon, which is close to the geomagnetic equator. COSMIC RO agrees best with ionosonde at Chumphon and worst at Chiang Mai. At each ionosonde station, the quality of COSMIC RO data degrades with the increase of solar activity. In addition, at the station Chiang Mai and Kototabang, COSMIC RO performs better in summer than in equinox and winter. Furthermore, the differences in foF2 derived from COSMIC RO and that from ionosonde measurements vary with local time, i.e., the differences in foF2 are generally smaller at night and larger in noontime when equatorial ionization anomaly (EIA) is well developed.     

超临界环境下煤油替代物液滴燃烧特性数值研究

为研究液氧/煤油火箭发动机燃烧室内经喷注形成的煤油液滴的燃烧过程，基于实际气体状态方程、高压热物性修正、高压气液平衡和详细化学反应动力学，建立一维的全瞬态液滴燃烧模型，对超临界环境下两组分煤油替代物液滴的燃烧特性及液滴初始直径的影响进行仿真研究。结果表明，在超临界环境下，相比于煤油液滴纯蒸发过程，煤油液滴燃烧过程的迁移时刻大大提前；煤油液滴着火之后很快进入超临界燃烧阶段，此时液滴燃烧过程可以看成中心附近的燃料高浓度区与外侧氧气高浓度区之间的扩散燃烧过程；煤油液滴的火焰半径先增大，达到最大值之后开始减小，并减小为零，火焰温度在着火之后快速上升至最大值，并基本保持不变，在火焰半径减小为零之后开始降低；随着液滴初始直径的增大，火焰特性以及液滴中心参数变化曲线趋势不变、整体延迟，着火时间、迁移时间和液滴寿命增大。     

火箭发动机超声速过膨胀射流气动噪声特性研究

采用大涡模拟LES方法计算了火箭发动机超声速过膨胀射流形态及近场声压分布,研究了入口温度与环境温度的比值(温度比)对声场的影响;将声源分解,基于Ffowcs Williams-Hawkings (FW-H)方程获取了不同位置噪声源的远场噪声,并根据声压级频谱和湍流形态分析了超声速射流噪声的产生机理。研究表明,超声速过膨胀射流气动噪声由湍流混合噪声和宽频激波噪声组成,近场噪声源以马赫波形式向大方位角辐射中高频噪声,下游大尺度湍流向低方位角范围辐射低频噪声,声压级峰值频率随观测角度增大而升高;随温度比升高,马赫波辐射角度增大,噪声指向性发生改变。该研究可为运载火箭发动机地面试车或火箭发射段声学环境设计提供参考。     

高能(450 kV)X射线参考辐射场附加过滤研究

利用MCNP程序对450kV X光机建立模型，计算各参考辐射质下的原级谱、平均光子能量。对ISO 4037-1中已有范围的管电压与附加过滤片厚度关系曲线进行二次拟合，确定模拟厚度范围。利用MCNP计算各附加过滤组合下的平均光子能量值，并与外推法得出的平均光子能量值进行对比，将相对偏差最小时的附加过滤作为最终确定值。从部分能量点的模拟与测量结果的对比可看出，模拟得出的平均光子能量在2%以内与PTB及中国计量院测量结果保持一致，附加过滤最大相对偏差为18%。     

Research on navigation of satellite constellation based on an asynchronous observation model using X-ray pulsar

Pulsar navigation is a promising navigation method for high-altitude orbit space tasks or deep space exploration. At present, an important reason for restricting the development of pulsar navigation is that navigation accuracy is not high due to the slow update of the measurements. In order to improve the accuracy of pulsar navigation, an asynchronous observation model which can improve the update rate of the measurements is proposed on the basis of satellite constellation which has a broad space for development because of its visibility and reliability. The simulation results show that the asynchronous observation model improves the positioning accuracy by 31.48% and velocity accuracy by 24.75% than that of the synchronous observation model. With the new Doppler effects compensation method in the asynchronous observation model proposed in this paper, the positioning accuracy is improved by 32.27%, and the velocity accuracy is improved by 34.07% than that of the traditional method. The simulation results show that without considering the clock error will result in a filtering divergence.     

航空航天制造机器人高精度作业装备与技术综述

新一代航空航天产品的研制与批产对制造精度与加工质量提出了更高的新要求。以机器人为核心的智能制造技术与装备是解决该难题的有效途径。然而,工业机器人较低的定位精度与弱刚性结构属性严重制约了其在航空航天部件高精度加工作业中的推广应用。本文在阐述国内外机器人装备在航空航天制造业的应用现状的基础上,重点介绍了机器人作业刚度强化策略与定位误差精确补偿方法的研究现状,并分析了现有高精度控制方法存在的问题及技术难点。最后探讨了机器人作业装备在航空航天制造领域的技术发展趋势,为面向航空航天产品的机器人高精度制造技术的研究提供参考与借鉴。