Scientific objectives and payloads of Tianwen-1, China’s first Mars exploration mission

This paper describes the scientific objectives and payloads of Tianwen-1, China’s first exploration mission to Mars. An orbiter, carrying a lander and a rover, lifted-off in July 2020 for a journey to Mars where it should arrive in February 2021. A suite of 13 scientific payloads, for in-situ and remote sensing, autonomously commanded by integrated payload controllers and mounted on the orbiter and the rover will study the magnetosphere and ionosphere of Mars and the relation with the solar wind, the atmosphere, surface and subsurface of the planet, looking at the topography, composition and structure and in particular for subsurface ice. The mission will also investigate Mars climate history. It is expected that Tianwen-1 will contribute significantly to advance our scientific knowledge of Mars.     

Simulation and Analysis of Electromagnetic Force in Laser Melting Deposition by Electromagnetic Impact

Magnetic field was introduced in laser melting deposition to reduce the pores in workpieces.Finite 3-D model of the coil-deposition layer-substrate was established.Simulation results show that the electromagnetic force in deposition layer mainly concentrates in the projection area of the coil.Axial electromagnetic force shows repulsion in one cycle.The experimental results indicate that the magnetic field is beneficial for grain refinement,microhardness increasement and decline of quantities and average sizes of pores.     

Event-triggered attitude control of spacecraft

The problem of spacecraft attitude stabilization control system with limited communication and external disturbances is investigated based on an event-triggered control scheme. In the proposed scheme, information of attitude and control torque only need to be transmitted at some discrete triggered times when a defined measurement error exceeds a state-dependent threshold. The proposed control scheme not only guarantees that spacecraft attitude control errors converge toward a small invariant set containing the origin, but also ensures that there is no accumulation of triggering instants. The performance of the proposed control scheme is demonstrated through numerical simulation.     

Parametric Modeling of Circuit Model for AC Glow Discharge in Air

In the parametric modeling of the circuit model for glow discharge in air,a new method for the design of glow discharge circuit model is presented.The new circuit model is an important reference for the design of plasma power supply,the simulation of glow discharge plasma actuator and the simulation of glow discharge plasma anemometer.The modeling approach consists in developing an electrical model of the glow discharge in air based on circuit components.The structure of the circuit model is established according to the theoretical analysis and the experimental device.Then the parameters of the circuit model are obtained based on the circuit analysis.Finally,the circuit model is verified by comparing the simulation current with the experimental current.This model takes into account the whole framework of the air glow discharge including the sheath and the plasma area.The built circuit model is feasible and reliable,thus being instructive for the investigation of the glow discharge in air.     

2024铝合金浸镍层的制备及生长过程

利用磷酸的全面腐蚀特性和氯离子的活化作用，设计了磷酸-氯化镍浸镍反应体系，通过表面电位监测及微观形貌表征对不同磷酸浓度与反应温度下的浸镍过程进行分析。结果表明:磷酸浓度是影响浸镍层表面电位及微观形貌的关键因素，当磷酸浓度为25%，反应温度为30℃时，可制得化学性质稳定、包覆性良好且晶粒尺寸均匀的浸镍层。在此反应体系下，浸镍层在形核后通过球状方式叠层生长，在反应进行600 s后得到厚度约1 μm的浸镍层，其表面电位可达到-0.51 V左右。      

Coupled Stress-Electricity Model for Electromagnetic Emission Induced by Concrete Fracture

Electromagnetic emission induced during concrete fracturing is of great significance to health monitoring of concrete structures.A coupled stress-electricity model is established by analyzing the interaction between stress and electricity during concrete fracturing.And based on this model,the electromagnetic radiation parameters are calculated.The theoretical calculation is well coincident with experimental results.This work provides theoretical support for concrete testing system.     

航空橡胶密封件力学与密封性能检测技术

介绍了航空橡胶密封件的力学、泄漏、损伤、接触变形等特性的无损检测技术及应用情况。其中,橡胶密封件泄漏压差测量方法,用于获得不同压差下的气体泄漏率;橡胶密封件接触应力超声检测技术,实现了橡胶密封接触应力的准确测量;橡胶密封件损伤与泄漏的红外热成像测试技术,可以得到泄漏点的定位与泄漏量的精确测量;橡胶密封件接触变形数字图像相关技术,获得了织物接触界面变形场与应力场的演化规律等。同时,对航空橡胶密封件的非接触测量技术进行了展望。     

B65A-S钢动态力学性能及本构模型的研究

为了研究B65A-S钢的动态力学行为,采用Instron液压试验机和分离式霍普金森压杆试验装置,在不同应变率和不同温度条件下对圆柱形试样进行准静态和动态加载试验。试验结果表明,材料的屈服强度与流动应力随着温度升高而降低;在温度一定时,随着应变和应变率的增大,材料的流动应力增高,具有典型的温度软化、应变强化和应变率强化特性。最后基于Jonson-Cook本构模型对试验数据拟合,得到B65A-S钢的Johnson-Cook本构模型参数。     

空间弯管的回弹预测

管材弯曲卸载后将不可避免地产生一定回弹,严重影响弯管生产的精度与效率,因此回弹成为管材弯曲的重点研究对象.对空间非平面弯管回弹进行研究,将空间回弹问题转化为两个相互垂直平面上的同弹问题,通过纯弯曲回弹实验,建立弯管平面弯曲回弹前后半径之间的函数关系式,然后将两个平面上的回弹合并,对离散化的回弹弯管进行空间拼接,进而完成...     

黏胶纤维在低温热处理过程中的热收缩性能

利用动态热机械分析仪结合热失重曲线和红外光谱图分析了黏胶纤维在低温热处理过程中的热收缩行为,研究了催化剂、张力等因素对热收缩性能的影响,并结合热解机理阐述了这一过程中黏胶纤维的结构变化,对于黏胶基碳纤维制备工艺参数的选取提供了一定信息.