The Toroidal Imaging Mass-Angle Spectrograph (TIMAS) for the polar mission

The science objectives of the Toroidal Imaging Mass-Angle Spectrograph (TIMAS) are to investigate the transfer of solar wind energy and momentum to the magnetosphere, the interaction between the magnetosphere and the ionosphere, the transport processes that distribute plasma and energy throughout the magnetosphere, and the interactions that occur as plasma of different origins and histories mix and interact. In order to meet these objectives the TIMAS instrument measures virtually the full three-dimensional velocity distribution functions of all major magnetospheric ion species with one-half spin period time resolution. The TIMAS is a first-order double focusing (angle and energy), imaging spectrograph that simultaneously measures all mass per charge components from 1 AMU e^–1 to greater than 32 AMU e^–1 over a nearly 360° by 10° instantaneous field-of-view. Mass per charge is dispersed radially on an annular microchannel plate detector and the azimuthal position on the detector is a map of the instantaneous 360° field of view. With the rotation of the spacecraft, the TIMAS sweeps out very nearly a 4 solid angle image in a half spin period. The energy per charge range from 15 eV e^–1 to 32 keV e^–1 is covered in 28 non-contiguous steps spaced approximately logarithmically with adjacent steps separated by about 30%. Each energy step is sampled for approximately 20 ms;14 step (odd or even) energy sweeps are completed 16 times per spin. In order to handle the large volume of data within the telemetry limitations the distributions are compressed to varying degrees in angle and energy, log-count compressed and then further compressed by a lossless technique. This data processing task is supported by two SA3300 microprocessors. The voltages (up to 5 kV) for the tandem toroidal electrostatic analyzers and preacceleration sections are supplied from fixed high voltage supplies using optically controlled series-shunt regulators.     

Integration of In-Situ Resource Utilization into lunar/Mars exploration through field analogs

The ability to extract and process resources at the site of exploration into useful products such as propellants, life support and power system consumables, and radiation and rocket exhaust plume debris shielding, known as In-Situ Resource Utilization or ISRU, has the potential to significantly reduce the launch mass, risk, and cost of robotic and human exploration of space. The incorporation of ISRU into missions can also significantly influence technology selection and system development in other areas such as power, life support, and propulsion. For example, the ability to extract or produce large amounts of oxygen and/or water in-situ could minimize the need to completely close life support air and water processing system cycles, change thermal and radiation protection of habitats, and influence propellant selection for ascent vehicles and surface propulsive hoppers. While concepts and even laboratory work on evaluating and developing ISRU techniques such as oxygen extraction from lunar regolith have been going on since before the Apollo 11 Moon landing, no ISRU system has ever flown in space, and only recently have ISRU technologies been developed at a scale and at a system level that is relevant to actual robotic and human mission applications. Because ISRU hardware and systems have never been demonstrated or utilized before on robotic or human missions, architecture and mission planners and surface system hardware developers are hesitant to rely on ISRU products and services that are critical to mission and system implementation success. To build confidence in ISRU systems for future missions and assess how ISRU systems can best influence and integrate with other surface system elements, NASA, with international partners, are performing analog field tests to understand how to take advantage of ISRU capabilities and benefits with the minimum of risk associated with introducing this game-changing approach to exploration. This paper will describe and review the results of four analog field tests (Moses Lake in 6/08, Mauna Kea in 11/08, Flagstaff in 9/09, and Mauna Kea in 1/10) that have begun the process of integrating ISRU into robotic and human exploration systems and missions, and propose future ISRU-related analog field test activities that can be performed in collaboration with non-US space agencies.     

Ignition system for oxygen/hydrogen auxiliary propulsion systems

When the oxygen/hydrogen bipropellant combination was selected for use in the Space Shuttle Main Engine, it became apparent that many advantages may result if the Auxiliary Propulsion System Engines were to use the same propellants. A new ignition system, possessing a dramatically new level of reliability, durability and response, is required because the oxygen/hydrogen combination is not hypergolic and the projected missions will require a very large number of fast-response engine starts.The objective of this program was to obtain basic data for spark torch ignition methods at operating conditions typical of a Space Shuttle Orbiter Auxiliary Propulsion System. The research included ignition analysis and igniter design, fabrication and hot-fire test.Extensive testing of spark torch igniters was performed (chamber pressure, 206.8 N/cm², 300 psia, nominal) in the Igniter-Only and Igniter-Complete Thruster (thrust, 6672 N, 1500 lbF, nominal) operational modes. Reliable, repeatable ignitions were obtained with spark energies of 1–10 mJ. Hot-fire test results showed there is no effect of back pressure (1.013 × 10⁵ to 1.333 × 10^?2 N/m², 7.60 × 10² to 1 × 10^?4 mm Hg) or low temperature (O₂, 170 K, 306 R; H₂, 107 K, 193 R) on the response of the igniter or the ignition delay of the thruster over the ranges tested. Igniter durability and pulse capability were demonstrated with 150 sec of continuous operation and 1000 consecutive pulses, respectively. Durability was further demonstrated with a series of 2500 Igniter-Complete Thruster ignitions at nominal chamber pressure. No limiting variables were encountered. The hot-fire test results showed the spark torch igniter is capable of meeting fully the typical Space Shuttle Orbiter Auxiliary Propulsion System mission requirements.     

The Plasma Ion and Electron Instruments for the Genesis Mission

The Genesis Ion Monitor (GIM) and the Genesis Electron Monitor (GEM) provide 3-dimensional plasma measurements of the solar wind for the Genesis mission. These measurements are used onboard to determine the type of plasma that is flowing past the spacecraft and to configure the solar wind sample collection subsystems in real-time. Both GIM and GEM employ spherical-section electrostatic analyzers followed by channel electron multiplier (CEM) arrays for detection and angle and energy/charge analysis of incident ions and electrons. GIM is of a new design specific to Genesis mission requirements whereas the GEM sensor is an almost exact copy of the plasma electron sensors currently flying on the ACE and Ulysses spacecraft, albeit with new electronics and programming. Ions are detected at forty log-spaced energy levels between ∼ 1 eV and 14 keV by eight CEM detectors, while electrons with energies between ∼ 1 eV and 1.4 keV are measured at twenty log-spaced energy levels using seven CEMs. The spin of the spacecraft is used to sweep the fan-shaped fields-of-view of both instruments across all areas of the sky of interest, with ion measurements being taken forty times per spin and samples of the electron population being taken twenty four times per spin. Complete ion and electron energy spectra are measured every ∼ 2.5 min (four spins of the spacecraft) with adequate energy and angular resolution to determine fully 3-dimensional ion and electron distribution functions. The GIM and GEM plasma measurements are principally used to enable the operational solar wind sample collection goals of the Genesis mission but they also provide a potentially very useful data set for studies of solar wind phenomena, especially if combined with other solar wind data sets from ACE, WIND, SOHO and Ulysses for multi-spacecraft investigations. This revised version was published online in August 2006 with corrections to the Cover Date.     

激光诊断技术在脉冲爆震发动机研究中的应用

在美国海军研究生院及斯坦福大学的脉冲爆震发动机（PDE）模型上，应用两种新发展的二极管激光诊断技术－光吸收／高温辐射组合测定法和多路复合可调二极管激光（TDL）技术，测量了其中的温度、各燃烧产物组分等重要参数，并与传统方法所得结果进行对比，说明新方法可靠、准确，适合爆震燃烧流场这种特殊环境，测量精度更高，而且更加简便、快捷。     

X-ray investigations of the hot ISM

At energies less than one keV, the intensity of the galactic x-ray background dominates that of the extragalactic background in almost every direction on the sky. Below 1/4 keV, the galactic x-ray background has a galactic stellar component, but the dominant emitter seems to be hot interstellar matter. The origin of the general 3/4 keV x-ray background remains uncertain, but one component must also be the contribution from hot interstellar matter. An overview is given of recent x-ray investigations of the hot interstellar medium using data from the ROSAT XRT/PSPC instrument. Several prominent features in the low energy x-ray background that are interpreted as fossil supernova remnants are discussed.     

Numerical modeling of unsteady flame propagation

The problem of the numerical modeling of unsteady flame propagation with large amounts of exothermic heat release has been addressed through the use of a model equation which contains many of the important nonlinearities and difficulties in the problem. The model equation has been solved for a significant variation in Damköhler number with a variety of conventional and new finite-difference procedures. One of the new procedures used was an adaptive grid method which places node points in the region of large temperature gradients where they are necessary for a proper simulation of the phenomena. This adaptive grid procedure does have significant advantages over conventional second and fourth order uniform grid methods for many aspects of the problem. It has been found that conventional methods with relatively few node points are inadequate for flames with high Damköhler number, because of the fact that too few nodes are located in the flame. Further refinement of the adaptive grid method seems feasible, but even in the present form it represents a significant improvement over conventional techniques.