基于自适应网格的钝头体激波诱导燃烧现象数值模拟研究

钝头体激波诱导燃烧是爆震研究的一个基本问题。针对化学恰当量比的H2/Air预混气在Ma=4.79和Ma=6.46时的激波诱导燃烧现象开展数值模拟研究，采用基于有限体积法的块结构自适应网格加密程序AMROC对带化学反应源项的轴对称Euler方程解耦求解，考察了数值模拟中不同形式的MUSCL重构格式、限制器类型以及化学反应机理等重要因素对模拟结果的影响。结果表明，程序能够根据设定的加密判据较好地实现网格自适应加密，减小总网格量，实现高效数值模拟。通过与实验数据的对比，表明非定常激波诱导燃烧算例的准确程度不仅取决于化学反应机理，也取决于限制器类型，而采用两种不同形式的MUSCL重构格式获得的振荡频率则几乎一致，与试验结果的误差分别为1.17%和0.97%。模拟对比经典的Jachimowski机理和近年来新发展的几种包含压力相关反应步的氢/氧反应机理，模拟结果表明：对于Ma=4.79时的非定常激波诱导燃烧模拟，经典的Jachimowski机理仍然是能够给出与实验结果最接近的反应机理；而对于Ma=6.46时的定常激波诱导燃烧模拟，几种反应机理均能给出与实验吻合较好的结果。     

Application of a modified generalized sail model on a solar sail with wrinkles

In this paper, we present an analysis of effect of wrinkles on the solar sail performance. We describe different analytical, semi-analytical and numerical approaches to the calculation of general large-scale curvature of a solar sail as well as parameters of so-called wrinkled domains, and introduce the impact of such wrinkles on the thrust and torque of the solar sail. Finally, we present a model of an optically-orthotropic surface for such non-ideal sail, providing a connection with the Generalized Sail Model, and other solar sail thrust models.     

不同直径圆球诱导燃烧的振荡机制与频率特性

为了分析不同直径圆球诱导振荡燃烧的规律，并揭示圆球大小在振荡燃烧现象中所发挥的深层次作用，本文采用二维轴对称Euler方程和基元反应模型，对不同直径的圆球在H2/air预混气体中诱导振荡燃烧的现象开展数值模拟研究。研究发现，振荡频率并不是简单地随直径增大而逐渐从高频向低频连续过渡，而是存在两次突变，形成了超高频、高频以及低频三种振荡燃烧模态。在两种模态间过渡时，振荡达到稳定状态前，会存在一段双频耦合的振荡阶段。三种不同振荡燃烧模态的产生是受到了不同振荡机制的作用，而两种模态间过渡时的双频耦合现象则是两种机制相互竞争的结果。     

详细化学反应机理对预混丙烷钝体熄火模拟影响

航空发动机熄火预测是重要关键问题之一，湍流和化学反应的非线性相互作用使预测非常困难。本文采用大涡模拟（LES）对湍流进行高精度模拟，采用概率密度函数输运方程湍流燃烧模型（TPDF）耦合JL4、Z66和H73三种化学反应机理，对预混丙烷钝体熄火现象和规律进行研究。JL4的反应机理最简单，反应释热快，局部放热高，火焰宽度大，火焰两侧温度梯度大，燃烧更加趋于稳定，无法模拟出熄火状态。H73机理绝热火焰温度低，火焰温度低，回流区中部OH含量高；在近熄火状态，大量CO被氧化，释放热量过高导致无法模拟出熄火现象。Z66机理可以模拟出火焰正常状态，在低当量比下也可以模拟出熄火状态。本文算例中，局部Da数大于1的区域超过35%则会发生熄火。     

航天器运输包装箱仿真验证平台技术研究

针对数量有限的物理跑车试验无法满足减振与保温性能测试需求的问题，提出一套航天器运输包装箱动力学与热学仿真验证方法，包括：建立适用于包装箱系统的刚柔耦合多体动力学系统，通过结合线路条件测试生成的动力学系统外部激励，实现减振性能虚拟跑车测试；建立基于计算流体力学的包装箱热学模型，通过模拟自然对流和空调控制，实现包装箱保温性能虚拟跑车测试；基于C/S架构和导航式流程设计思想，建立航天器运输包装箱仿真验证平台，通过实际案例证明该平台仿真结果与实际跑车测试数据具有较高的一致性。     

空间载荷机柜热控设计的仿真研究

空间站主动热控系统的作用是提供和保持航天员、仪器设备和结构部件所要求的温度、湿度和风速等热环境。本文以空间载荷机柜为热控系统的基本单元，建立了以单相流体循环回路为基础、采用液冷结合风冷的冷却方式的载荷机柜数学模型；介绍了模糊增量控制算法的工作原理；提出了采用模糊增量控制算法，以液冷支路进出口温差和风冷支路冷却量占总冷却量的比值为控制目标的反馈控制策略。同时文章采用数值模拟方法研究了控制系统的动态响应效果。仿真结果显示，模糊增量控制算法具有响应迅速、超调量小、无静态误差的特点，控制策略满足有效性、稳定性和高精确度的要求。     

Comparison of GPS derived TEC with the TEC predicted by IRI 2012 model in the southern Equatorial Ionization Anomaly crest within the Eastern Africa region

We have compared the TEC obtained from the IRI-2012 model with the GPS derived TEC data recorded within southern crest of the EIA in the Eastern Africa region using the monthly means of the 5 international quiet days for equinoxes and solstices months for the period of 2012 – 2013. GPS-derived TEC data have been obtained from the Africa array and IGS network of ground based dual-frequency GPS receivers from four stations (Kigali (1.95°S, 30.09°E; Geom. Lat. 11.63°S), Malindi (2.99°S, 40.19°E; Geom. Lat. 12.42°S), Mbarara (0.60°S, 30.74°E; Geom. Lat. 10.22°S) and Nairobi (1.22°S, 36.89°E; Geom. Lat. 10.69°S)) located within the EIA crest in this region. All the three options for topside Ne of IRI-2012 model and ABT-2009 for bottomside thickness have been used to compute the IRI TEC. Also URSI coefficients were considered in this study. These results are compared with the TEC estimated from GPS measurements. Correlation Coefficients between the two sets of data, the Root-Mean Square Errors (RMSE) of the IRI-TEC from the GPS-TEC, and the percentage RMSE of the IRI-TEC from the GPS-TEC have been computed. Our general results show that IRI-2012 model with all three options overestimates the GPS-TEC for all seasons and at all stations, and IRI-2001 overestimates GPS-TEC more compared with other options. IRI-Neq and IRI-01-corr are closely matching in most of the time. The observation also shows that, GPS TEC are underestimated by TEC from IRI model during noon hours, especially during equinoctial months. Further, GPS-TEC values and IRI-TEC values using all the three topside Ne options show very good correlation (above 0.8). On the other hand, the TEC using IRI-Neq and IRI-01- corr had smaller deviations from the GPS-TEC compared to the IRI-2001.     

考虑测试性设计缺陷修正延时的测试性增长模型建模与评价方法

针对现有测试性增长模型忽略了测试性设计缺陷的修正延时过程，进而导致测试性增长模型（TGM）跟踪与预计精度低的问题，提出了一种考虑测试性设计缺陷修正延时的测试性增长模型建模理论与方法。首先分析测试性设计缺陷识别与修正之间的延时机理，得到剩余测试性设计缺陷（TDL）具有先增后减的铃形变化趋势；在此基础上，分别以Gamma、Raleigh和Delay-S 3种曲线拟合剩余测试性设计缺陷（RTDL）变化趋势，研究建立基于以上3种曲线考虑修正延时的测试性增长模型；最后，以某机载稳定跟踪平台测试性增长试验数据验证测试性增长模型拟合、跟踪及预计效能。研究结果表明：基于该测试性增长试验数据，Gamma曲线可以精确地拟合剩余测试性设计缺陷变化规律，测试性增长模型跟踪和预计精度可达到10^-2数量级。     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

双流制窄轨电力机车用异步牵引电机设计

将牵引电机应用于双流制窄轨电力机车时,由于窄轨机车轨距小,所以牵引电机安装空间异常狭小,比一般牵引电机在安装空间、电机结构、电磁负荷等方面的要求更加苛刻。针对窄轨双流制电力机车的运用特点和特殊要求进行了分析,提出了牵引电机的设计要求和关键技术难点,并对关键技术难点给出了相应的分析和解决措施。对该牵引电机的制造过程及电机试验测试情况进行了论述。试验结果表明,该牵引电机达到了设计预期,完全能满足设计要求。