弹载变转速定量泵高动态压力控制特性分析

传统弹载电液伺服系统的液压能源采用有刷直流电机驱动恒压变量泵的方式，泵源压力在导弹飞行过程中设定值恒定，但在平飞段过程长、负载小，对能源压力需求低，造成弹上能源总利用率不高的问题，提出无刷直流电机驱动小排量液压泵的压力控制泵源的设计，在低气动负载阶段适当降低系统压力，进而降低节流损失与泄漏量，提高能量利用率。分析了变转速定量泵的流量压力特性曲线，通过建立基于变转速压力控制泵源的位置电液伺服系统数学模型与仿真模型，分析了变转速定量泵压力控制系统在典型工况下的位置跟踪、系统压力变化与能量利用效率，验证了压力控制系统能够在导弹平飞段保证位置伺服系统跟踪正常的前提下，能有效提高系统效率，证明了变转速定量泵压力控制系统的有效性与可行性。     

高背压等离子点火器及其液体燃料点火特性实验研究

航天应用的液体火箭发动机及燃烧型加热器燃烧室室压高、燃料流量大、温度低、有重复启动需求，实现安全可靠点火的难度较大。针对这些需求，研究了一种采用高背压设计的电弧等离子体点火器。实验研究了Ar，N₂气体工质在高进气压力下的伏安特性，发现N₂在宽压力范围内适用于点火。发射光谱分析表明，在高达数MPa的进气压力下，Ar，N₂等离子体射流电子密度符合局部热力学平衡判据（LTE判据），点火能量集中。N₂等离子体整体温度低于Ar，但阳极喷口附近温度高于Ar，N₂等离子体射流火焰长，卷吸沿程空气造成射流平均温度偏低，但有助于低温液体推进剂的蒸发混合和强化点火。等离子体射流引起了臭氧和氮氧化物的形成，具有促进点火和化学反应的作用。背压提高引起电源输出电压升高，提高供气压力和电流，有助于点火器在高背压环境中稳定电压。燃烧型空气加热器燃烧室的点火实验发现，采用N₂等离子体喷注面中心点火，可以在短时间内完成酒精-空气和酒精-液氧-空气的点火，最高燃烧室室压接近5MPa时，点火器仍能稳定工作，多次使用电极烧蚀不明显，在液体火箭发动机的重复可靠点火方面具有很好的应用前景。     

An empirical solar radiation pressure model for satellites moving in the orbit-normal mode

We present a family of empirical solar radiation pressure (SRP) models suited for satellites orbiting the Earth in the orbit normal (ON) mode. The proposed ECOM-TB model describes the SRP accelerations in the so-called terminator coordinate system. The choice of the coordinate system and the SRP parametrization is based on theoretical assumptions and on simulation results with a QZS-1-like box-wing model, where the SRP accelerations acting on the solar panels and on the box are assessed separately. The new SRP model takes into account that in ON-mode the incident angle of the solar radiation on the solar panels is not constant like in the yaw-steering (YS) attitude mode. It depends on the elevation angle of the Sun above the satellite’s orbital plane. The resulting SRP vector acts, therefore, not only in the Sun-satellite direction, but has also a component normal to it. Both components are changing as a function of the incident angle. ECOM-TB has been used for precise orbit determination (POD) for QZS-1 and BeiDou2 (BDS2) satellites in medium (MEO) and inclined geosynchronous Earth orbits (IGSO) based on IGS MGEX data from 2014 and 2015. The resulting orbits have been validated with SLR, long-arc orbit fits, orbit misclosures, and by the satellite clock corrections based on the orbits. The validation results confirm that—compared to ECOM2—ECOM-TB significantly (factor 3–4) improves the POD of QZS-1 in ON-mode for orbits with different arc lengths (one, three, and five days). Moderate orbit improvements are achieved for BDS2 MEO satellites—especially if ECOM-TB is supported by pseudo-stochastic pulses (the model is then called ECOM-TBP). For BDS2 IGSOs, ECOM-TB with its 9 SRP parameters appears to be over-parameterized. For use with BDS2 IGSO spacecraft we therefore developed a minimized model version called ECOM-TBMP, which is based on the same axis decomposition as ECOM-TB, but has only 2 SRP parameters and is supported by pseudo-stochastic parameters, as well. This model shows a similar performance as ECOM-TB with short arcs, but an improved performance with (3-day) long-arcs. The new SRP models have been activated in CODE’s IGS MGEX solution in Summer 2018. Like the other ECOM models the ECOM-TB derivatives might be used together with an a priori model.     

The adjusted optical properties for Galileo/BeiDou-2/QZS-1 satellites and initial results on BeiDou-3e and QZS-2 satellites

Solar Radiation Pressure (SRP) is the dominant non-gravitational perturbation for GNSS (Global Navigation Satellite System) satellites. In the absence of precise surface models, the Empirical CODE Orbit Models (ECOM, ECOM2) are widely used in GNSS satellite orbit determination. Based on previous studies, the use of an a priori box-wing model enhances the ECOM model, especially if the spacecraft is a stretched body satellite. However, so far not all the GNSS system providers have published their metadata. To ensure a precise use of the a priori box-wing model, we estimate the optical parameters of all the Galileo, BeiDou-2, and QZS-1 (Quasi Zenith Satellite System) satellites based on the physical processes from SRP to acceleration. Validation using orbit prediction proves that the adjusted parameters of Galileo and QZS-1 satellites exhibit almost the same performance as the corresponding published and “best guess” values. Whereas, the estimated parameters of BeiDou-2 satellites demonstrate an improvement of more than 60% over the initial “guess” values. The resulting optical parameters of all the satellites are introduced into an a priori box-wing model, which is jointly used with ECOM and ECOM2 model in the orbit determination. Results show that the pure ECOM2 model exhibits better performance than the pure ECOM model for Galileo, BeiDou-2 GEO and QZS-1 orbits. Combined with the a priori box-wing model the ECOM model (ECOM+BW) results in the best Galileo, BeiDou-2 GEO and QZS-1 orbits. The standard deviation (STD) of satellite laser ranging residuals reduce by about 20% and 5% with respect to the pure ECOM2 model for Galileo and BeiDou-2 GEO orbits, while the reductions are about 40% and 60% for QZS-1 orbits in yaw-steering and orbit-normal mode respectively. BeiDou-2 IGSO and MEO satellite orbits do not benefit much from the a priori box-wing model. In summary, we suggest setting up a unified SRP model of ECOM+BW for Galileo, QZS-1, and BeiDou-2 orbits based on the adjusted metadata. In addition, we estimate the optical parameters of BeiDou-3e and QZS-2 satellites using a limited number of tracking stations. Results regarding the unified SRP model indicate the same advantages, the STD of satellite laser ranging residuals reduces by about 30% and 20% for QZS-2 and BeiDou-3e orbits respectively over orbit products without a priori model. The estimation procedure is effective and easy to apply to the new emerging satellites in the future.     

螺旋桨滑流对发动机进气道气动性能的影响

针对螺旋桨/短舱/进气道一体化构型,采用多重参考系(MRF)法和滑移网格非定常法进行了数值模拟研究,实现了螺旋桨/短舱/进气道一体化内外流耦合流场仿真,研究了不同工况下螺旋桨滑流对进气道气动性能的影响,并与无桨构型的进气道性能进行了对比,最后通过数值分析解释了螺旋桨桨盘后总压上升的原因。结果表明:多重参考系法和滑移网格非定常法对进气道出口的时均参数的计算结果吻合较好,多重参考系法可用于螺旋桨及进气道的气动性能参数计算;螺旋桨做功使进气道总压恢复系数增高,螺旋桨转速越大,总压恢复系数的增量就越大,且螺旋桨滑流使进气道出口畸变指数明显增大;通过数值分析推导的桨盘前后总压关系公式与仿真结果的误差均在3%以内。      

逆向进气复合角发散冷却孔流量系数试验

针对回流燃烧室外环壁面冷气与燃气流动方向相反的情况,试验研究了发散孔进气方向与环腔通道气流流动方向相反的条件下,复合角发散冷却孔流量系数随发散孔倾角(25°~55°)、偏角(90°~180°)及压降系数等参数的变化规律。研究结果表明:复合角发散孔的流量系数随倾角的增大而增大,随偏角的增大而减小；随着压降系数的增大,复合角发散孔的流量系数先呈近似线性增长,当压降系数大于0.95后,呈非线性增长且增长速度减缓。      

酚醛树脂基纳米多孔材料的制备及结构调控

酚醛树脂基纳米多孔材料（Phenolic Resin-based Nanoporous Materials，PNM）是满足新一代航天飞行器轻质、高效隔热需求的新型热防护材料，传统制备方法中需使用超临界干燥技术，制备周期长、成本高。本研究通过两步法，即先合成线性酚醛树脂，再进行溶胶-凝胶的方法，实现了常压干燥PNM的制备。系统研究了固化剂含量、固化温度和固化时间对材料结构的影响和调控作用，分析了影响材料收缩率和热稳定性的因素。结果表明，PNM的微观纳米结构的变化会影响材料干燥后的收缩率，制备大颗粒、大孔径的微观结构更有利于降低材料的收缩率。而PNM的热稳定性主要受交联反应过程形成的化学结构的影响，通过优化固化剂的含量可提高PNM的热稳定性。当固化剂含量为10%，固化温度提高至150℃，固化时间延长至48 h的条件下，获得的PNM有最高的热稳定性（900℃下的残碳率为54.2%）、最发达的孔结构（比表面积为264.0 m²/g、孔容为2.67 cm³/g、平均孔径为40.0 nm）和最小的收缩率（0%）。此PNM制备方法简单、性能优异，在未来航天飞行器上有广阔的应用前景。     

ZL205A合金舱体低压工艺设计及数值仿真应用

针对某ZL205A合金舱体铸件壁薄难充型、壁厚差异大、易产生裂纹等特点,设计了低压底注式浇注工艺。采用立筒缝隙式浇注系统分配充型过程中合金的流量,局部厚大部位放置成形冷铁加快该部位的冷却速度,以控制铸造缺陷的产生。利用ProCast数值仿真软件对工艺进行仿真计算,成功预测了缺陷的产生位置,对工艺方案进行优化,包括倒角过渡、改变型砂使用等,并在优化方案的基础上浇注了舱体铸件,铸件质量良好,没有缩松、缩孔、裂纹等缺陷,符合相关技术要求。     

双模块下颌式内转进气道/圆锥前体一体化布局研究

为实现三维内转进气道的内收缩流场与圆锥前体的外压缩流场的良好匹配，提出了一种双模块下颌式内转进气道/圆锥前体(Double-modules Chin Inward-turning Inlet and Conical Forebody，DCII/CF)一体化设计方法，获得一种新颖的双发并置、侧向安装的DCII/CF一体化布局。针对该布局形式，开展了DCII/CF一体化构型与传统的单模块内转进气道/圆锥前体(Single-module Inward-turning Inlet and Conical Forebody，SII/CF)一体化构型的数值对比研究。结果表明：DCII/CF一体化布局不仅为内转进气道提供了优秀的前体附面层排移效果，还有效避免了传统SII/CF布局中前体附面层与进气道内部流场之间的相互干扰。在Ma∞=6.0设计状态，DCII/CF一体化布局的进气道总压恢复系数相较传统的SII/CF布局有了显著提高，从0.403提高至0.482；但由于前体附面层的排移，该布局的捕获流量略有降低， SII/CF的流量系数为0.956，该布局则为0.917。而在非设计状态，该布局形式同样具备较好的总压恢复性能，在Ma∞=5.0与Ma∞=4.0的总压恢复系数分别达到了0.586和0.682，明显高于SII/CF的总压恢复系数0.507和0.619。     

Application of a modified generalized sail model on a solar sail with wrinkles

In this paper, we present an analysis of effect of wrinkles on the solar sail performance. We describe different analytical, semi-analytical and numerical approaches to the calculation of general large-scale curvature of a solar sail as well as parameters of so-called wrinkled domains, and introduce the impact of such wrinkles on the thrust and torque of the solar sail. Finally, we present a model of an optically-orthotropic surface for such non-ideal sail, providing a connection with the Generalized Sail Model, and other solar sail thrust models.