半球谐振子疲劳寿命分析与仿真

半球谐振子的寿命和损伤是直接影响高精度半球谐振陀螺使用时长和安全性的重要因素。目前国内加工的半球谐振子所用的熔融石英玻璃材料主要依靠进口，采用传统的疲劳寿命实验确定方法成本过于昂贵，因此需要利用疲劳分析软件对半球谐振子的疲劳寿命进行分析。文章通过半球谐振陀螺应力分析，采用ANSYS软件对熔融石英半球谐振子进行应力分析仿真，确定因残余应力所引起的疲劳危险部位，并在疲劳部位进行裂纹扩展分析，得到 、 和 型应力强度因子，以使在半球谐振子结构设计和使用过程中对易疲劳的部位进行有效监控和预防。     

基于DOA聚类算法的ARM抗有源诱偏技术研究

有源诱偏技术是雷达对抗反辐射导弹的一种重要手段,可以大大降低反辐射导弹的作战效能。为提高对敌目标的精确打击能力,在分析闪烁诱饵诱偏原理的基础上,针对有源诱偏干扰下被动雷达测角精度与稳定度不高的问题,通过对有源诱偏信号的时域特征进行分析,提出一种基于脉冲前沿检测的DOA聚类分选算法,找出前沿超前的辐射源信号,实现了高性能抗有源诱偏干扰和高精度抗干扰测向。仿真结果表明,该技术可以有效对抗四点源有源诱偏干扰。     

Validation of non-linear split window algorithm for land surface temperature estimation using Sentinel-3 satellite imagery: Case study; Tehran Province,Iran

In recent years, land surface temperature (LST) has become critical in environmental studies and earth science. Remote sensing technology enables spatiotemporal monitoring of this parameter on large scales. This parameter can be estimated by satellite images with at least one thermal band. Sentinel-3 SLSTR data provide LST products with a spatial resolution of 1 km. In this research, direct and indirect validation procedures were employed to evaluate the Sentinel-3 SLSTR LST products over the study area in different seasons from 2018 to 2019. The validation method was based on the absolute (direct) evaluation of this product with field data and comparison (indirect) evaluation with the MODIS LST product and the estimated LST using the non-linear split-window (NSW) algorithm. Also, two emissivity estimation methods, (1) NDVI thresholding method (NDVI-THM) and (2) classification-based emissivity method (CBEM), were used to estimate the LST using the NSW method according to the two thermal bands of Sentinel-3 images. Then, the accuracy of these methods in estimating LST was evaluated using field data and temporal changes of vegetation, which the NDVI-THM method generated better results. For indirect evaluation between the Sentinel-3 LST product, MODIS LST product, and LST estimated using NSW, four filters based on spatial and temporal separates between pairs of pixels and pixel quality were used to ensure the accuracy and consistency of the compared pairs of a pixel. In general, the accuracy results of the LST products of MODIS and Sentinel-3, and LST estimated using NSW showed a similar trend for LST changes during the seasons. With respect to the two absolute and comparative validations for the Sentinel-3 LST products, summer with the highest values of bias (?1.24 K), standard deviation (StDv = 2.66 K), and RMSE (2.43 K), and winter with the lowest ones (bias of 0.14 K, StDv of 1.13 K, and RMSE of 1.12 K) provided the worst and best results for the seasons in the period of 2018–2019, respectively. According to both absolute and comparative evaluation results, the Sentinel-3 SLSTR LST products provided reliable results for all seasons on a large temporal and spatial scale over our studied area.     

A novel framework for liquid propellant engine’s cooling system design by sensitivity analysis based on RSM and multi-objective optimization using PSO

One of the challenges of combustion chamber and nozzle design in a Liquid Propellant Engine (LPE) is to predict the behavior and performance of the cooling system. Therefore, while designing, the optimization of the cooling system is always of great importance. This paper presents the multi-objective optimization of the LPE’s cooling system. To this end, a novel framework has been developed, resulting from the application of the Response Surface Method (RSM) and the correlation coefficients matrix, sensitivity analysis and the The Particle Swarm Optimization (PSO). based on this method, the input variables, constraints, objective functions, and their surfaces were identified. In terms of multi-optimization algorithms, RSM and PSO are utilized to get global optimum. In conclusion, the methodology capability is to optimize the LPE’s cooling system, 6 percentage increase in total heat transfer and 7 bar decrease cooling system pressure loss, which resulted in a 1.2-seconds increase in the specific impulse of the engine.     

微等离子体转化二氧化碳发射光谱诊断

火星大气层的主要成分为二氧化碳，如果能够利用低温等离子体方法高效分解二氧化碳，使其转化为氧气和一氧化碳加以利用，可以大幅降低航天员生命保障相关载荷长途运输的成本，进一步提高生命保障能力。低温等离子体放电过程中会产生大量活性组分，可以在数百度温度下实现二氧化碳的高效解离，是具有很大潜力的二氧化碳解离与转化方式。设计了一种尺度在亚毫米级、功率输入为数瓦的直流微槽等离子体反应器，可以在较低气体温度下实现二氧化碳分解。测量了反应器电流、功率等放电参数，采用发射光谱确定了体系中激发态组分，分析了激发态粒子谱线强度随输入电压、稀释气体比例等反应器工作参数变化，利用氮气分子振转谱带测量了等离子体放电区振动温度和气体温度。研究表明，添加氩、氦、氮气均可以增强二氧化碳的分解，添加氦气可以促进二氧化碳的电离过程。稀释气体激发态因具有高能量，可以通过潘宁解离通道增强二氧化碳分解。氦组分激发态的能量高于二氧化碳电离能，可以促进二氧化碳的电离反应。微等离子体内存在强烈的振动 平动非平衡现象：振动温度约为4400~4800K，而气体温度仅为450 ~600K，表明可以通过合理的放电和结构设计，定向将能量注入到振动态，从而进一步促进二氧化碳的振动解离。     

模块化永磁直线游标电机等效磁网络及漏磁分析

在模块化永磁直线游标电机的初始设计及优化设计中,使用有限元方法(FEM)计算漏磁系数时需要耗费大量的建模和计算时间。针对这一问题,建立该种电机的等效磁网络模型,在建模期间,考虑气隙中的边缘效应,并计算永磁体组与定子齿在不同相对位置时的等效磁导,得到该种电机在一个周期内不同相对位置时的漏磁磁导和漏磁系数的数学解析表达式。采用FEM验证了该数学解析表达式的准确性。研究结果为模块化永磁直线游标电机的设计提供了理论依据。     

基于MFC的拉扭复合系统界面设计

为了方便对拉扭复合系统中2台伺服电机的控制,设计了基于MFC的上位机界面。通过串口通信,使用不同的按钮操作设置伺服驱动器相应参数,从而控制2台伺服电机的运行。上位机实时接收伺服驱动器监控数据绘制出转速、位移、转矩曲线。针对在数据接收过程中信息帧接收错误的情况,使用拼接两相邻错误信息帧的方法进行修复。结果表明:上位机界面实现了系统功能及对电机运行工况的监控。     

无刷双馈电机静止坐标系数学模型的研究

由于没有电刷和滑环,提高了运行的可靠性,降低了维护成本,因此无刷双馈电机(BDFM)在变速恒频发电领域有着广阔的应用前景。由于特殊的结构和工作原理,BDFM数学模型十分复杂。从BDFM多回路空间矢量数学模型出发,推导出了两个静止坐标系之间的坐标变换关系以及功率绕组静止坐标系数学模型和控制绕组静止坐标系数学模型,推导过程简洁明了。所得结果为BDFM理论分析和不同控制策略的研究提供了理论基础。MATLAB/Simulink环境下的仿真结果验证了数学模型及坐标变换关系的正确性。     

模型预测控制在永磁同步电机系统中的应用发展综述

随着数字技术的发展,模型预测控制(MPC)已经广泛应用于交流传动系统。首先介绍了经典MPC策略——有限控制集MPC和连续控制集MPC的原理。其次综述了多步预测控制、多矢量预测控制、具有参数鲁棒性的预测控制、广义模型预测、显式模型预测这些常见的改进MPC的研究现状,并提出相关研究思路。最后,根据MPC的应用需求和研究现状,展望了未来需要进一步深入和拓展的研究方向。     

A new modeling scheme for powered parafoil unmanned aerial vehicle platforms: Theory and experiments

A novel framework is established for accurate modeling of Powered Parafoil Unmanned Aerial Vehicle (PPUAV). The model is developed in the following three steps: obtaining a linear dynamic model, simplifying the model structure, and estimating the model mismatch due to model variance and external disturbance factors. First, a six degree-of-freedom linear model, or the structured model, is obtained through dynamic establishment and linearization. Second, the data correlation analysis is adopted to determine the criterion for proper model complexity and to simplify the structured model. Next, an active model is established, combining the simplified model with the model mismatch estimator. An adapted Kalman filter is utilized for the real-time estimation of states and model mismatch. We finally derive a linear system model while taking into account of model variance and external disturbance. Actual flight tests verify the effectiveness of our active model in different flight scenarios.