A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

在二元柔壁自适应风洞中利用面元法进行三元模型实验

简要叙述了在西北工业大学二元柔壁自适应风洞中利用面元法进行二元半机翼模型试验的研究情况，分析了面元法的基本思想和部分试验结果。     

航天主要金属结构材料与肼的相容性

概括地探讨了金属材料和肼相容性的基本原理和研究重点，叙述了６０年代以来国外金属材料和肼相容性研究的发展，较详细地介绍了了钛合金，不锈钢和铝合金在推进剂中相容性的研究成果并进行了总结归纳。     

随振动量级增加卫星结构频率下移的分析

对卫星振动频率随量级增加而出现下降，即振动频率“漂移”的现象进行了初步分析。发现随振动量级的增加。结构的非线性表现突出。结构的刚度下降和阻尼增加，可认为主要是由蜂窝材料的非线性因素所致。     

钛合金焊接件疲劳特性评估的当量Kt法

针对先进飞机结构广泛采用的钛合金焊接结构,提出了描述焊接件疲劳特性的当量理论应力集中系数Kt(K_te)的概念;建立了以钛合金材料疲劳性能为基础,通过一组谱载下钛合金焊接件疲劳试验来确定K_te的技术途径.以TC4钛合金氧弧焊试件为例给出了确定K_te的具体方法和结果.     

翼板颤振主动抑制的无限维非线性分析

 <正> 1.混合动力学系统的Hopf分叉定理 本文将Marsden-McCracken关于分布参数的Hopf分叉定理推广至混合动力学系统。 设在积空间X=E×R~n中依赖参数μ的演化方程为     

双轴应力下含裂纹加筋曲板剩余强度的弹塑性有限元计算

 采用考虑了大应变的弹塑性有限元方法,以裂纹尖端张开角为断裂准则,实现了双向受载条件下加筋曲板中裂纹起裂到失稳整个扩展过程的数值模拟计算;还对与加筋曲板有同样尺寸的加筋平板进行了分析和计算。结果表明,所提出的分析方法和所采用的断裂准则适用于对含裂纹加筋结构所进行的剩余强度分析。     

钛合金TC11深孔钻削刀片材料的选择

在研究了钛舍金材料切削性能的基础上，针对钛合金的特点，选用了五种国内常用的硬质舍金刀片材料，对钛合金进行深孔钻削刀具磨损试验。结果表明，确定了适合钻削钛合金TC11的硬质合金刀片材料。     

运载火箭阻尼安装板的设计

 <正>运载火箭在起飞和着陆时的瞬态载荷和飞行过程中的气动力的随机激励都是宽频带的。在这种环境中安装精密仪器的仪表板若采用过去常规的橡皮减振器减振已很难保证在较宽频带内都能起到应有的减振作用。利用阻尼材料做成的夹层板减振，国内外已做了大量的工作^[t~3]，取得了较为明显的效果。本文针对产品设计中要解决的减振问题，提出了设计思想、计算分析与试验方法。     

高深径比TC4钛合金筒形件普旋成型有限元数值模拟

采用有限元法对特定高深径比TC4钛合金筒形件普旋成型进行了数值模拟,分析了运动轨迹、旋压道次间距和间隙对成型的影响.结果表明普旋时坯料不同部位的应力应变状态不同,采用凹曲线轨迹,间隙为3.5 mm,首道次间距为9 mm,分6道次旋压成型效果好.同时在有限元数值模拟基础上,成功旋制了高精度试验件,说明有限元模拟对旋压具有很好指导意义.