交流阻抗谱法评价热障涂层的热腐蚀行为(英文)

本文利用交流阻抗这种无损检测的方法研究了热障涂层在质量分数为25%NaCl+75%Na2SO4混合盐体系中的热腐蚀行为。实验结果显示,热腐蚀条件下,在陶瓷层和粘结层界面处形成TGO层为混合氧化物层,成分为Cr2O3、(Ni,Co)(Cr,Al)2O4和NiO,其厚度增长符合抛物线规律。热障涂层在110个循环腐蚀之前时,TGO层的电阻值随其厚度的增加而增加;110个循环后,虽然TGO层的厚度还是在增加,但由于TGO层孔隙的增多而导致其电阻值有所下降。陶瓷层的电阻值随着陶瓷层中裂纹的萌生和扩展而不断增大。等效电路中得到的参数可以用来表征热障涂层的失效行为。     

一种基于承载效率准则的复合材料机翼结构布局优化方法(英文)

提出一种针对大型复合材料机翼结构的二级布局优化策略。系统级根据结构形变调整设计指标,子系统级优化结构布局以满足系统级约束。将机翼壁板中各种临界失效载荷的接近程度作为评判结构效率的标准,通过将结构效率作为优化目标,保证了所求解问题的连续性。加筋壁板通过等效的正交异性板模拟,并根据能量原理预测总体失稳载荷。讨论了加强筋支持弹性对于蒙皮抵抗局部失稳性能的影响,并通过神经网络代理模型对其进行逼近。采用解析模型对失效特性做出评估,减少了计算资源的占用。最后以一种大型机翼结构的综合优化作为算例,计算结果满足设计要求,验证了该方法的可行性。     

一种基于误差四元数的战术导弹垂直发射姿态调转控制器

针对战术导弹垂直发射姿态调转时的快速性要求，研究了垂直发射快速姿态调转的控制问题。首先基于误差四元数并结合垂直发射的具体特点，建立了战术导弹垂直发射的非线性数学模型；然后通过李亚普诺夫第二方法进行控制系统设计，得出了基于误差四元数反馈控制器。分析了系统的稳定性和鲁棒性。该控制器实现了绕欧拉特征轴的旋转，缩短了姿态调转的时间，最后通过仿真验证其有效性。     

用户星对中继卫星的跟踪规律研究

根据中继卫星系统中用户星跟踪中继卫星的要求，定义了用户星天线坐标系，推导出了用户星天线对中继卫星的跟踪规律。通过该跟踪规律可以推出用户星天线跟踪中继卫星的跟踪角度、角速度和角加速度。同时，在给定系统一定初始条件的情况下，利用该跟踪规律分别推出了用户星最大跟踪角度和角速度与用户星轨道高度和用户星轨道倾角之间的关系。最后利用STK(Satellite Tool Kit)对该跟踪规律进行了间接验证。     

向心透平叶片角动量分布的优化

 以n条子午流线,给出满足约束条件的各自角动量分布的若干不同组合构成初始复合形,做复合形每一顶点处该向心透平叶轮S2 流面与跨叶片面势流场分析,并以二元紊流边界层动量厚度计算经三元修正,分析叶轮效率,最终使复合形法成功应用于向心透平叶片角动量分布的优化。该方法也适用于离心叶轮中叶片加载量的优化。     

Deformation Behavior of Medium-strength TA18 High-pressure Tubes During NC Bending with Different Bending Radii

To improve the forming quality and forming limit of the numerical control (NC) bending of high-pressure titanium alloy tubes, in this study, using three-dimensional (3D) finite element method, deformation behavior of medium-strength TA18 high-pressure tubes during NC bending with different bending radii is investigated. The results show that the cross-sectional deformation and the wall thickness variation during NC bending of TA18 tubes using a small bending radius (less than 2 times of tube outside diameter) are clearly different from that using a normal bending radius (between 2 and 4 times of tube outside diameter). For bending with a normal bending radius, with or without a mandrel, the distribution of the flattening in the bending area resembles a platform and an asymmetric parabola, respectively. For bending with a small bending radius, with or without a mandrel, the flattening both distributes like a parabola, but the former has a stable peak which deflects toward the initial bending section, and the latter has a more pronounced peak with a bending angle and deflects slightly toward the bending section. The wall thickness variations with a normal bending radius, with and without a mandrel, both resemble a platform when the bending angle exceeds a certain angle. For the bending with a small radius, the distribution of the wall thickness variation without a mandrel follows an approximate parabola which increases in value as the bending angle increases. If a mandrel is used, the thickening ratio increases from the initial bending section to the bending section.     

一种机器人砂带磨削的路径规划方法(英文)

机器人砂带磨削系统具有弹性接触和宽行加工两个显著优点,被广泛应用在具有复杂工件的终加工领域,提高表面质量和加工效率。有关在曲率约束下的磨削路径规划研究较为少见。由于工件与接触轮之间存在复杂的弹性接触,因此,机器人磨削路径可以利用接触运动学的一般方法来求解。机器人砂带磨削过程且需要满足一般的砂带磨削工艺要求,其中最重要的是保证接触轮与工件的局部几何特征贴合。在曲率较小的局部,相邻刀位点的弧长加大,以保证加工效率。相反地,在曲率较大的局部,相邻刀位点的弧长较小,以保证加工精度。利用一系列平面与目标曲面相截,得到相应的截平面的轮廓曲线。对于任意一条轮廓线,优化相邻刀位点之间的弧长,在曲率较大的局部增加一个中间刀位点。本文提出了一种包含弧长优化和主曲率匹配的磨削路径生产方法,通过离线仿真验证了有效性,并利用该方法提高了曲面的磨削质量。该路径规划方法为生成光顺且精确的机器人曲面磨削路径提供了理论依据。     

Double-stage Metamodel and Its Application in Aerodynamic Design Optimization

Constructing metamodel with global high-fidelity in design space is significant in engineering design. In this paper, a double-stage metamodel (DSM) which integrates advantages of both interpolation metamodel and regression metamodel is constructed. It takes regression model as the first stage to fit overall distribution of the original model, and then interpolation model of regression model approximation error is used as the second stage to improve accuracy. Under the same conditions and with the same samples, DSM expresses higher fidelity and represents physical characteristics of original model better. Besides, in order to validate DSM characteristics, three examples including Ackley function, airfoil aerodynamic analysis and wing aerody-namic analysis are investigated. In the end, airfoil and wing aerodynamic design optimizations using genetic algorithm are presented to verify the engineering applicability of DSM.     

单站多普勒跟踪定轨的优化算法

由于低轨道小卫星应用的日益广泛，在轨卫星数目的迅速膨胀，对传统的多个地面站相互协调管理卫星领域模式提出了挑战。小卫星的低成本特性必然要求存在与之相应的地面站设施降低复杂性、降低成本。本文针对当前已提出的单站多普勒定轨方案，进一步研究了多普勒定轨的有关方法，提出和建立了多普勒定轨的优化算法与模型，最后进行了仿真分析与模型的有效性验证。     

Study of ADS-B Data Evaluation

In western China, the terrain and meteorological conditions are so complex that it is not suitable to construct new radar stations. Automatic dependent surveillance-broadcast (ADS-B) is a totally new surveillance method, so before practically applied and operated in China, abundant tests and evaluations are necessary to validate the performance of ADS-B and guarantee the operational security. During the flight tests, we collect the data of radar, ADS-B and high accuracy position and compare the performance of ADS-B with radar based on high accuracy position. To solve the asynchronous problem among radar data, ADS-B data and real-time kinematic (RTK) data caused by different update rates, this article proposes the technique of synchronizing multi-surveillance data by extrapolating from the data of low update rate to high update rate according to velocity and heading. Meanwhile, because radar data, ADS-B data and RTK data are expressed in different coordinates and cannot be compared each other, this article provides a method to unifying the coordinates of multi-surveillance data. By the analysis and evaluation, we can conclude that the performance of ADS-B is better than radar.