纳秒脉冲电子束冲击强化金属表面的研究

讨论了纳秒强脉冲电子束(功率密度为10⁹W/cm²)辐射金属表面后产生的强化作用.纳秒脉冲电子束瞬间在材料表面局部区域注入巨大能量,使金属表面微区瞬间产生高温高压和冲击作用,并产生骤热急冷过程,使材料表面硬度、耐腐蚀性和其他物化性能发生明显变化.文中讨论了脉冲电子束导致快速熔凝的热传导过程,并分析了从扫描电镜照片观察到的金属急冷过程的显微结构.纳秒强脉冲电子束注入是金属材料表面改性的新手段.     

Al 量对 Ni-Al-Hf-Cr-W 系合金显微组织结构的影响

研究了Ni-20Hf-8Cr-8W-（4～6）Al系列合金的显微组织以及Al含量对共晶组织的影响,结果表明：此系列合金中,随着Al含量的微小变化,会析出不同的共晶组织;当Al含量大于5.5wt%时,出现（β-NiAl+Ni7Hf2）或（γ′+β-NiAl+Ni7Hf2）共晶：当Al量小于5.5wt%时,会出现（γ′+Ni7Hf2）、（γ+γ′+Ni7Hf2）或（γ+Ni7Hf2）共晶组织。并且得出（Ni-20Hf-8Cr-8W-5.3Al）wt%的合金具有（γ′+Ni7Hf2）共晶,适宜选做为以Ni7Hf2增强的共晶复合材料的合金成份。     

制备工艺对NiAl-30Fe-Y合金组织与性能的影响

研究了铸态、挤压态、热轧态和定向凝固结晶４种不同制备工艺对ＮｉＡｌ－３０Ｆｅ－Ｙ合金组织与性能的影响。结果表明,热轧和定向凝固结晶工艺明显改善了合金性能,特别是提高了合金室温塑性。在室温下不同制备工艺其拉伸断口特征明显不同。不同制备工艺仅对微观组织形态产生影响,其合金组织皆是由先共晶Ｂ２结构β和β与（γ＋γ'）共晶相组成,定向凝固合金成长方向为＜２１１＞β‖＜１００＞（γ＋γ'）。     

Improving tensile-shear properties of friction stir lap welded dissimilar Al/Mg joints by eliminating hook defect and controlling interfacial reaction

To improve tensile-shear properties of fiction stir lap welded(FSLW) dissimilar Al/Mg joints, pin-tip profiles were innovatively designed and welding speed was optimized, and effects of them on formation, interface microstructure and mechanical properties of different FSLW joints were investigated. With increasing the welding speed, the tensile-shear load of FSLW joints produced by three pins presents an increasing firstly and then decreasing trend. Compared with Rpin, the hook and hole defect i...     

BT-14钛合金舱口外盖白斑问题

BT-14钛板为某产品舱口盖结构用材料,焊前检查时,发现钛板表面有数量不等的白色圆状斑点。文章从白斑的外观形貌、微观组织以及力学性能等方面进行分析,重点研究了白斑组织对钛板使用性能的影响,并提出后续生产中的预防措施。     

固溶前退火处理对2050铝锂合金冷轧薄板力学性能与组织的影响

采用拉伸性能测试、电子背散射衍射分析(EBSD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM),研究了固溶前退火处理(300℃/4 h,400℃/2 h)对2050铝锂合金冷轧薄板T8时效后力学性能、晶粒组织和析出相的影响。研究结果表明:固溶前退火处理导致2050铝锂合金冷轧薄板固溶态不完全再结晶数量增多,晶粒长厚比增大,小角度晶界比例增加,同时使合金Goss织构密度增大。T8时效后主要强化相为T_1相和θ′相。固溶前退火处理可导致后续T8时效时T_1相在不同{111}_(Al)面上析出差异,其中部分{111}_(Al)面上T_1相析出减少,而预拉伸变形时承受高分切应力{111}_(Al)面上T_1相析出增加,从而影响合金的力学性能。固溶前300℃/4 h退火处理可使T8时效后合金屈服强度和抗拉强度提高,伸长率基本保持不变。     

TC4-DT钛合金线性摩擦焊接头组织特征及其形成机制

研究TC4-DT损伤容限型钛合金线性摩擦焊(linear friction welding,LFW)接头的组织特征及形成机制。利用光镜和扫描电镜对接头各区域微观组织进行表征,利用显微硬度计测试接头的显微硬度分布。结果表明:接头焊缝区(WZ)发生动态再结晶,焊接过程中WZ温度超过β转变点,焊后快冷的条件下发生了β→α′及β→α两种相变并析出了大量α′马氏体以及二次层片α;TC4-DT钛合金母材(BM)组织具有较高的变形抗力,使得接头形成的热力影响区(TMAZ)较窄。TMAZ内组织在强烈的热力耦合作用下拉长变形并破碎,焊后快冷的条件下析出少量α′马氏体及大量二次层片α;毗邻TMAZ的热影响区(HAZ)基本保留了BM不同位向的α集束的组织特征,但受热的影响α集束内α/β相界两侧元素相互扩散,层间β消耗,初生α长大;WZ组织的细晶强化和第二相强化,TMAZ组织的应变强化和第二相强化,以及HAZ内α相的长大使得接头上述区域显微硬度均高于BM。     

Effect of Isothermal Forging on the Microstructure and Mechanical Properties of Mg-8Gd-3Y-0.5Zr Alloy

Aiming at the problems of poor plastic forming ability， narrow forging temperature range， and strain rate sensitivity of rare earth magnesium alloys， a study on the microstructure and mechanical properties of Mg-8Gd-3Y-0.5Zr alloy with different isothermal forging processes is carried out. The microstructure and properties of the alloy in the as-cast， isothermal forged， and post-aging states after forging are studied with optical microscope (OM)， scanning electron microscope (SEM)， and tensile testing. The results show that significant dynamic recrystallization occurs during the isothermal forging process， a fine equiaxed grain structure is formed， and the mechanical properties of the alloy are greatly improved. When the isothermal forging temperature is 460 ºC and the strain rate is 0.02 s－1， the alloy structure performance is the best， the room temperature tensile yield strength (TYS) is 218 MPa， the ultimate tensile strength (UTS) is 299 MPa， and the fracture elongation (FE) is 19.2%. When the alloy is post-forging artificial aged， the α-Mg matrix is dispersed， the Mg5(Gd，Y) phase is precipitated， the UTS of the alloy is increased to 392 MPa， and the FE is reduced to 12.0%.     

激光熔化沉积15-5PH沉淀硬化不锈钢组织及拉伸性能

利用激光熔化沉积技术制备15-5PH沉淀硬化不锈钢板,利用金相显微镜(OM)、扫描电镜(SEM)、透射电镜(TEM)、电子探针(EPMA)技术,对沉积态组织进行分析,测试沉积态组织的室温拉伸性能。结果表明:激光熔化沉积15-5PH不锈钢沉积态组织由沿沉积增高方向贯穿多层外延生长的柱状晶组成,柱状晶内包含多个细长整齐排列的胞状树枝晶,枝晶内为马氏体组织,枝晶间为铁素体;沉积态组织中弥散分布大量细小的NbC析出相,尺寸12～20 nm;15-5PH不锈钢沉积态组织具有良好的力学性能,纵向抗拉强度和延伸率分别为1 128.5 MPa和14.0%,横向抗拉强度和延伸率分别为1 101 MPa和12.25%。     

Microstructure and Hot Deformation Behavior of Mg-9Al-3Si-0.375Sr-0.78Y Alloy

Using Gleeble-3500 thermal simulator， the high temperature plastic deformation behavior and microstructure evolution of Mg-9Al-3Si-0.375Sr-0.78Y alloy are investigated at the temperature of 523 K?673 K and the strain rate of 10-3 s-1?10 s-1. True strain-true stress curves show the characteristics of the typical dynamically recrystallization process. The Arrhenius constitutive equation of the hyperbolic model is established. The average activation energy and the strain rate sensitivity index are， respectively， 221.578 kJ.mol-1 and 0.137. The result shows that the α-Mg phase exhibits dynamic recrystallization (DRX) characteristics obviously. But no DRX occurs in theβ-Mg17Al12 phase. Hot deformation does not affect the primary Mg2Si phase. Under the conditions of low temperature (523 K?673 K) and high strain rate (1 s-1?10 s-1)， the flow instability and macro-defects such as crack appear in the specimens. However， there are finer recrystallization grains. Under the conditions of high temperature (≥673 K) or low strain rate， the microstructure of the alloy shows good homogeneity. The size of the primary Mg2Si phase is uniform， the size of the β-Mg17Al12 phase is small， and the distribution of the β-Mg17Al12 phase is uniform.