基于多项式平方和规划的航空发动机鲁棒LPV/PI控制

针对航空发动机常规(proportion integration,PI)控制器设计过程中难以保证鲁棒性及参数适应性差等问题,提出了一种基于线性变参数(linear parameter varying,LPV)模型及多项式平方和(sum of squares,SOS)规划的控制器设计方法.结合传递函数模型下的鲁棒稳定条件及弱对偶定理给出了多项式描述的LPV模型鲁棒稳定条件,并转化为便于求解的SOS规划问题.根据发动机非线性模型获取不同转速下的传递函数模型,并利用多项式拟合的方法建立发动机LPV模型.根据所提出的定理构造出SOS规划问题,并求解得出LPV/PI控制器.最终以某型双轴涡扇发动机为被控对象,在包线内不同点进行了阶跃仿真,结果表明:高压转子转速控制系统的稳态误差为0,调节时间小于3s.      

正十七烷与正十八烷对航空煤油理化性能及液滴平均直径的影响

讨论了正十七烷与正十八烷(C₁₇,C₁₈)对燃料运动黏度、密度、表面张力理化性能的影响,探究了直链烷烃对SMD(Sauter mean diameter)的影响.将Key's混合规律、Tat混合规律和多项式拟合应用于密度公式的拟合,并将Key's混合规律与对数拟合应用于运动黏度公式的拟合,得出的理化性能拟合公式精度较高;通过测量纯煤油及C₁₇,C₁₈混合油雾化的SMD,实验发现随着直链烷烃的质量分数的增加,混合油的运动黏度增加,SMD也随之增加,雾化效果与纯航空煤油的相比较差,而C₁₈混合油的SMD要比C₁₇混合油要大,并且利用密度、运动黏度的拟合公式对SMD进行预测的偏差小于0.3%.      

固体火箭发动机流体喉部推力矢量特性

针对采用水作为二次流工质的流体喉部进行了冷流实验及数值模拟研究.研究了该种固体火箭发动机流体喉部的一般规律,包括不同二次流射流方式,不同二次流流量下流体喉部的扼流性能,推力偏角及推力效率,数值模拟及实验结果吻合较好.结果表明:扼流性能与二次流的注射位置、注射角度及流量比有关,且随二次流/主流流量比的增大而增大.喉部二次流喷射能有效的调节有效喉部面积进而调节推力大小,当流量比为0.4时,最大有效喉部面积比为0.8;扩张段二次流喷射能有效调节推力方向,当流量比为0.4时,最大推力偏角为20°;喉部二次流与扩张段二次流入射位置存在相位差可有效降低喉部与扩张段二次流干扰.      

Machining of a film-cooling hole in a single-crystal superalloy by high-speed electrochemical discharge drilling

Single-crystal superalloys are typical advanced materials used for manufacturing aeroengine turbine blades. Their unique characteristics of high hardness and strength make them exceedingly difficult to machine. However, a key structure of a turbine blade, the film-cooling hole,needs to be machined in a single-crystal superalloy; such machining is challenging, especially considering the increasing levels of machining efficiency and quality demanded by the aeroengine industry. Tube electrode high-speed electrochemical discharge drilling(TSECDD), a hybrid technique of high-speed electrical discharge drilling and electrochemical machining, provides high machining efficiency and accuracy, as well as eliminating the recast layer. In this study, TSECDD is used to machine a film-cooling hole in a nickel-based single-crystal superalloy(DD6). The Taguchi methods of experiment are used to optimise the machining parameters. Experimental results show that TSECDD can effectively drill the film-cooling hole; the optimum parameters that give the best performance are as follows: pulse duration: 12 ls, pulse interval: 30 ls, peak current:6 A, and salt solution conductivity: 3 m S/cm. Finally, a hole is machined by TSECDD, and the results are compared with those obtained by electrical discharge machining. TSECDD is found to be promising for improving the surface quality and eliminating the recast layer.     

Gust response analysis and wind tunnel test for a high-aspect ratio wing

A theoretical nonlinear aeroelastic response analysis for a flexible high-aspect ratio wing excited by harmonic gust load is presented along with a companion wind tunnel test. A multidisci-plinary coupled numerical calculation is developed to simulate the flexible model wing undergoing gust load in the time domain via discrete nonlinear finite element structural dynamic analysis and nonplanar unsteady vortex lattice aerodynamic computation. A dynamic perturbation analysis about a nonlinear static equilibrium is also used to determine the small perturbation flutter bound-ary. A novel noncontact 3-D camera measurement analysis system is firstly used in the wind tunnel test to obtain the spatial large deformation and responses. The responses of the flexible wing under different static equilibrium states and frequency gust loads are discussed. The fair to good quanti-tative agreements between the theoretical and experimental results demonstrate that the presented analysis method is an acceptable way to predict the geometrically nonlinear gust response for flex-ible wings.     

A new steering approach for VSCMGs with high precision

A new variable speed control moment gyro (VSCMG) steering law is proposed in order to achieve higher torque precision. The dynamics of VSCMGs is established, and two work modes are then designed according to command torque:control momentum gyro (CMG)/reaction wheel (RW) hybrid mode for the large torque case and RW single mode for the small. When working in the CMG/RW hybrid mode, the steering law deals with the gimbal dead-zone nonlinearity through compensation by RW sub-mode. This is in contrast to the conventional CMG singularity avoidance and wheel speed equalization, as well as the proof of definitely hyperbolic singular property of the CMG sub-mode. When working in the RW single mode, the motion of gimbals will be locked. Both the transition from CMG/RW hybrid mode to RW single mode and the reverse are studied. During the transition, wheel speed equalization and singularity avoidance of both the CMG and RW sub-modes are considered. A steering law for the RWs with locked gimbals is presented. It is shown by simulations that the VSCMGs with this new steering law could reach a better torque precision than the normal CMGs in the case of both large and small torques.     

改进的粒子群算法求解飞机位姿评估问题

在飞机装配中,要求调姿基准点距离误差和最小以及各点距离误差满足容差条件。以往的飞机位姿评估算法注重距离误差和最小,可能出现调姿基准点的距离误差不满足容差约束的情况。为了求解在满足容差约束条件下的距离误差和最小的飞机位姿参数,提出一种新的优化模型,将带容差约束转化为带惩罚函数,与距离误差和一同作为优化目标,采用求解约束优化问题的粒子群算法进行求解。在上述算法上进一步改进,通过动态改变约束参数来加强约束条件,可以通过迭代方式进一步减小飞机调姿基准点最大距离误差。仿真算例和蒙特卡洛分析证明,求解约束优化的粒子群算法和改进的粒子群算法在求解飞机位姿评估问题时,求解得到的调姿测量点最大误差小于奇异值分解法。     

基于LabVIEW的超精密磨床嵌入式监控系统

针对超精密磨削机床的监控需求,基于NI–sbRIO硬件平台开发了一套应用于超精密磨床状态监测和数据采集的嵌入式监控系统,使用FPGA对温度、振动、声发射等信息进行实时数据采集,并使用实时处理器对数据进行分析和处理,实现对机床的实时状态监测和数据存储。通过FPGA编程取代硬件数据采集卡,成本低,灵活性强。试验表明,该系统能够胜任超精密磨床的监控任务。     

基于模型的装备维修性设计控制技术

伴随数字化设计方法日趋成熟,飞机装备维修性设计面临如何与三维数字化设计环境下功能性能设计同步的难题。对比分析了数字化环境维修性设计与传统维修性设计的主要差别,提出了基于飞机装备数字化设计环境维修性设计流程,研究了维修性设计参数的表达模型以及维修性参数信息在三维设计数字环境中的转化、集成与利用方式。基于图论和网络节点框图,提出了一种以节点网络图、单节点维修时间模型、维修过程时间模型为表征的飞机装备维修性设计与控制方法。经实例验证,提出的这套基于数字模型的维修性设计技术,对装备在数字化设计环境下同步开展维修性设计具有一定的工程指导价值。     

前可变面积涵道引射器特性的试验与数值模拟

为了研究主、次流的进口总压比及出口背压对前可变面积涵道引射器(FVABI)工作特性的影响与流动掺混机理,采用试验与三维数值模拟方法对不同进口总压比下引射器工作性能及掺混流场随背压变化规律进行了分析。结果表明:标准k -ε模型用于引射器掺混流场的模拟具有较好的准确性;进口总压比越大,引射器总压损失越大;进口总压比不变,随背压增加,引射器总压损失先减小后增加;进口总压比不变,引射器在背压变化过程中存在总压损失最小点;背压减小时,引射器存在临界工况点,且进口总压比越大达到临界工况点的背压越大,可变涵道比的范围变窄;主、次流掺混过程主要集中在沿气流方向上x/l=03~06位置之间,在黏性力作用下动量、质量充分交换,沿流向截面速度径向分布趋于均匀。