Thermal-structural analysis of regenerativelycooled thrust chamber wall in reusable LOX/Methane rocket engines

To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a validated 3-D finite volume fluid-thermal coupling computational method.With the specified loads,the nonlinear thermal-structural finite element analysis is applied to obtaining the 3-D thermal and structural responses.The Chaboche nonlinear kinematic hardening model calibrated by experimental data is adopted to predict the cyclic plastic behavior of the inner wall.The methodology is further applied to the thrust chamber of LOX/Methane rocket engines.The results show that both the maximum temperature at hot run phase and the maximum circumferential residual strain of the inner wall appear at the convergent part of the chamber.Struc tural analysis for multiple work cycles reveals that the failure of the inner wall may be controlled by the low-cycle fatigue when the Chaboche model parameter γ3 =0,and the damage caused by the thermal-mechanical ratcheting of the inner wall cannot be ignored when γ3 ＞ 0.The results of sen sitivity analysis indicate that mechanical loads have a strong influence on the strains in the inner wall.     

应用于超级电容储能系统的双向DC/DC变换器混沌控制方法研究

超级电容储能系统(SCESS)主要通过对双向DC/DC变换器进行控制来快速平抑直流母线电压的波动。为了抑制控制过程中所产生的一些分岔和混沌现象,提出了一种应用于SCESS的混沌控制方法。分析了该方法的控制原理,并根据非线性动力学理论建立了双向DC/DC变换器的离散迭代模型；然后设计了一种能够自动调节补偿斜率的混沌控制信号；最后对该信号作用下的异步切换函数和同步切换映射式进行了数值求解,从而绘出系统分叉图。通过仿真和试验证明,该方法能够有效抑制SCESS的分岔和混沌现象,提高了系统的稳定工作范围和动态响应速度。     

Modeling novel methodologies for unmanned aerial systems–Applications to the UAS-S4 Ehecatl and the UAS-S45 Bálaam

The rising demand for Unmanned Aerial Systems(UASs) to perform tasks in hostile environments has emphasized the need for their simulation models for the preliminary evaluations of their missions. The efficiency of the UAS model is directly related to its capacity to estimate its flight dynamics with minimum computational resources. The literature describes several techniques to estimate accurate aircraft flight dynamics. Most of them are based on system identification. This paper presents an alternative methodology to obtain complete model of the S4 and S45 unmanned aerial systems. The UAS-S4 and the UAS-S45 models were divided into four sub-models, each corresponding to a specific discipline: aerodynamics, propulsion, mass and inertia, and actuator. The‘‘aerodynamic" sub-model was built using the Fderivatives in-house code, which is an improvement of the classical DATCOM procedure. The ‘‘propulsion" sub-model was obtained by coupling a two-stroke engine model based on the ideal Otto cycle and a Blade Element Theory(BET) analysis of the propeller. The ‘‘mass and the inertia" sub-model was designed utilizing the Raymer and DATCOM methodologies. A sub-model of an actuator using servomotor characteristics was employed to complete the model. The total model was then checked by validation of each submodel with numerical and experimental data. The results indicate that the obtained model was accurate and could be used to design a flight simulator.     

小型固定翼无人机绳钩回收过程动力学分析

绳钩回收作为小型固定翼无人机的一种精确定点拦阻无损回收技术,近年来在国内外得到迅速发展。本文以某型无人机的绳钩回收系统为研究对象,对绳钩回收系统进行了参数化处理并建立了两种动力学仿真模型。一是在考虑回收架柔性基础上建立了基于Lagrange方程的绳钩回收系统的动力学仿真模型,二是在考虑绳索变形和系统结构细节基础上建立了基于MSC.ADAMS的绳钩回收系统的多体动力学仿真模型。通过上述两种仿真模型的算例分析以及与某型无人机绳钩回收试验的测试数据作对比,验证了两种动力学仿真模型在绳钩回收系统不同设计阶段的适用性和有效性。     

一种温度动态调节方法及其动态性能仿真研究

航空气源模拟试验台主要用于模拟不同飞行状态时发动机给空气管理系统的供气,由于飞机爬升、降落时发动机供气参数会急剧变化,因此航空气源模拟试验台需具备动态能力.基于一种温度动态调节方法,在合理简化的基础之上采用NHT方法对其温度动态性能进行了仿真研究,仿真结果表明该温度动态调节方法能够满足温度动态性能需求,对动态航空气源模拟试验台的设计选型有较高的参考价值.     

耐高温异氰酸酯/ 环氧树脂固化历程与性能

以异氰酸酯为固化剂固化环氧树脂,通过比较不同固化条件下固化物结构的差异,研究了异氰酸酯与环氧树脂的反应历程;改变异氰酸酯/环氧树脂体系的化学计量比(I/E),采用FTIR/ATR、DSC、DMTA等研究了固化产物的结构与性能。结果表明,异氰酸酯与环氧树脂的固化历程随着温度的升高可分为三个阶段,第一阶段为异氰酸酯的三聚反应;第二阶段是一个复杂的过程,首先环氧树脂和异氰酸酯可反应生成嗯唑烷酮结构,通过嗯唑烷酮环扩链得到端畀氰酸酯基低聚物,可继续发生三聚反应;第三阶段为异氰脲酸酯与残余的环氧基团反应生成嗯唑烷酮结构,异氰脲酸酯六元环向噁唑烷酮五元环的转化是一个可逆的过程。不同的I/E比例可得到结构不同的固化物,不同的结构导致固化物性能的差异:当(I/E)=1.8时,综合力学性能良好,异氰酸酯/环氧树脂/玻璃纤维复合材料的弯曲强度、弯曲模量、层剪强度分别为652.53、33270.63和31.66MPa,优于甲基四氢苯酐/环氧树脂/玻璃纤维复合材料力学性能;当I/E=2.0时,固化物T_g达到了305℃,明显优于传统的环氧树脂固化体系。     

Numerical analysis of hypersonic thermochemical non-equilibrium environment for an entry configuration in ionized flow

A theoretical methodology for thermochemical non-equilibrium flow combing with the HLLC (Harten-Lax-van Leer Contact) scheme was applied to study the hypersonic thermochemical non-equilibrium environment of an entry configuration in ionized flow. A two-temperature controlling model was utilized and the Gupta’s 11 species (N₂, O₂, NO, O, N, NO⁺, N₂⁺, O₂⁺, N⁺, O⁺, e^?) thermochemical non-equilibrium model was taken. Firstly, numerical calculations of hypersonic thermochemical non-equilibrium environments for different aerodynamic shapes were carried out to verify the reliability of the method above. Then, the method was used to research the effects of ionization and wall catalysis on the hypersonic thermochemical non-equilibrium environment of the entry configuration in ionized flow. The shock stand-off distance can be reduced by thermochemical reactions but doesn’t continue to decrease significantly when ionization occurs. The shock stand-off distance calculated by the 11 species model is 4.2% smaller than that calculated by the 5 species (N₂, O₂, NO, O, N) thermochemical non-equilibrium model without considering ionization. Ionization reduces wall heat flux but increases wall pressure a little. The effect of ionization on aerothermal loads is greater than that of aerodynamic loads. The thermochemical reactions of electrons and ions catalyzed at the wall increase wall heat flux significantly but make a small change in wall pressure. The maximum wall heat flux obtained by only considering the electrons and ions catalyzed at the partially catalytic wall condition is 11.8% less than that calculated at the super-catalytic wall condition.     

涡环伞降末敏子弹的稳态扫描动力学特性

综合采取理论建模、高空自由落体试验及可视化仿真相结合的方法,研究了一种涡环伞降末敏子弹的稳态扫描动力学特性。基于第一类拉格朗日方程,建立了由弹体、降落伞、伞盘、摩擦盘、连杆所组成的五刚体动力学模型,并应用ADAMS、MATALB及VR相结合的方法进行了弹道计算和可视化仿真研究。通过在高空热气球上投放试验样弹的方法,得到了伞弹系统的运动图像、平均落速、转速等弹道数据。对比研究得出:涡环伞的运动稳定性良好,可使末敏子弹保持匀速旋转降落状态,弹体达到稳定后的落速约为13.5 m/s,转速约为3 r/s,稳态扫描角接近于弹体的静态悬挂角,仿真计算与试验结果的一致性较好。      

高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响

为了研究高主流湍流度下二次流密度比对涡轮导叶全气膜冷却特性的影响,使用热色液晶测量了在主流湍流度为15%,二次流密度比为1.0和1.5下三维涡轮导叶的气膜冷却效率和换热系数。二次流与主流质量流量比为7.0%和12.5%。结果表明:二次流密度比增大可以降低冷气射流的动量,小流量比工况下,在叶片前缘和压力面前半段,动量较低的二次流在高主流湍流度的影响下更易耗散,增大二次流密度比使冷却效率明显降低;大流量比工况下,二次流动量降低使气膜孔后区域冷气贴附性增强,气膜冷却效率和冷气覆盖效果均得到提升。小流量比工况下,二次流密度比增大对叶片表面换热的影响较小;大流量比工况下,二次流密度比增大使吸力面中弦区域和压力面后半段的平均换热系数比分别降低15%和25%。     

考虑非理想噪声干扰的直升机飞行动力学模型辨识方法

利用MATLAB/SIMULINK平台搭建了直升机仿真实验系统，并以UH-60直升机为对象实现了考虑非理想噪声干扰的仿真飞行实验。建立了非理想噪声数学模型并基于增广最小二乘法设计 了一套同时考虑模型参数和噪声参数的综合辨识算法，在此基础上，利用仿真实验数据实现了UH-60直升机纵向飞行动力学模型的辨识与验证。最后，通过与普通最小二乘法的对比验证了本文方法的优越性。 