基于涡流发生器的风洞侧壁附面层控制

为降低风洞侧壁附面层对半模型数据的影响,在前期数值模拟的基础上,研制了一种适用于2.4m跨声速风洞半模型试验段侧壁的梯形涡流发生器,并进行了试验验证.结果表明:加装涡流发生器效果明显,亚声速范围内能够使附面层厚度降低20%~30%,对主气流均匀性影响可忽略;加装后半模型零升阻力系数降低,升力线斜率增大,压力中心向机身移动,体现了明显的附面层减薄效果,证明所研制的涡流发生器可应用于亚声速半模型试验中.      

Design and implementation of rigid-flexible coupling for a half-flexible single jack nozzle

The aerodynamic design of a rigid-flexible coupling profile is the decisive factor for the flow-field quality of a supersonic free jet wind tunnel nozzle, and its mechanic dynamic features are the key for engineering implementation of continuous Mach number regulations. To fulfill the requirements of a free jet inlet/engine compatibility test within a wide simulation envelop, both uni-form flow-fields of continuous acceleration and deceleration are necessary. In this paper, the aero-dynamic design methods of an expansion wall and machinery implementation plan for the half-flexible single jack nozzle were researched. The profile control in nozzle flexible plate design was studied with a rigid-flexible coupling method. Design and calculations were performed with the help of numerical simulation. The technique of axial free stretching of the flexible plate was used to improve the matching performance between the designed elasticity profile and the theoretical one, and the rigid-flexible coupling structure was calibrated by wind tunnel tests. Results indicate that the flexible plate aerodynamic design method used here is effective and feasible. Via rigid-flexible coupling design, the flexible plate agrees with the rigid body very well, and continuous Mach number changes can be achieved during the tests. The nozzle’s exit flow-field uniformity meets the requirements of China Military Standard (GJB).     

基于激光多普勒原理的极低风速测量实验

介绍了利用激光多普勒效应进行风速测量的原理及定点遥测原理,分析了探测气溶胶颗粒大小的要求,并以此搭建了一套极低风速测量系统。同时分析了系统的测速精度,以及安装角度对测量结果的影响。最后分别开展了转台实验、直线导轨实验和风洞实验,实验结果表明,该极低风速测量系统的测量误差基本可以控制在001 m/s以内,当风洞工作介质为未经处理的环境空气时,系统可以获得稳定可靠的信号,测量结果与高性能仪器十分接近。     

0.3 m低温风洞液氮供给系统研制

基于系统级的一维热流体模拟分析,建立了适用于研究分析0.3 m低温风洞液氮供给系统的数学模型,并开展了系统漏热、两相流及缓冲罐中液氮容积等流体动力学分析;在系统现有控制策略及试验数据的基础上,基于该数学模型开展了系统压力动态响应分析,获得了在阀门动态调节过程中管网压力的瞬态响应,计算结果与试验值的总体误差控制在10%以内。喷射压力一致化改造避免了阀间干扰,添加的回流管道消除了供给末端的两相流现象,使喷射压力控制精度达到1.1%,调节时间减少到23 s,实现了风洞总温快速安全调节和精确控制。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

共轴式直升机桨毂阻力特性与减阻试验

共轴式直升机桨毂阻力占全机废阻的50%以上,因此有必要对桨毂阻力特性和减阻设计进行研究。 通过对某共轴式直升机桨毂模型、减阻方案及减阻方案加装涡流发生器进行风洞试验,研究轴式直升机桨毂的 阻力特性,验证减阻方案及减阻方案加装涡流发生器的减阻效果。结果表明:桨毂支臂方位角、转速和攻角变 化对桨毂及其减阻方案的阻力影响很小;上下桨毂整流罩与中间轴整流罩之间的缝隙对阻力影响比较大;减阻 方案可以降低约33%的桨毂阻力,而加装涡流发生器的减阻效果并不明显。     

基于绳系并联机器人支撑系统的SDM动导数试验可行性研究

详细给出了在低速风洞中,采用绳系并联机器人(WDPR)支撑模型,用强迫振荡法进行标准动态模型(SDM)动导数试验可行性的研究。试验中将杆式六分量应变天平内置入模型中以测量模型的气动力和气动力矩,建立了适用于绳系并联机器人支撑系统的模型运动控制子系统和数据采集子系统。采用绳拉力作为参考信号,对气动力矩信号与位姿信号进行数据的同步处理,解决了绳系并联机器人支撑系统应用于动导数试验时所测力矩信号与位姿信号之间的相位差确定问题,给出了WDPR支撑下模型动导数的计算方法。整个试验样机置于某开口式低速直流风洞中进行了俯仰、带偏航角的俯仰以及升沉的动导数试验,通过测量和计算得到各动导数。试验结果与参考文献相比较具有合理的一致性。研究结果表明,采用绳系并联机器人支撑模型进行动导数试验是可行的,至少对于SDM是这样的结果;使用一套绳系并联机器人支撑系统,可以完成多套硬式支撑系统才能完成的动导数试验,从而提高试验效率,降低试验成本。     

风力机组叶片的先进翼型族设计

大型风力机组叶片设计需要专用的翼型族,以满足风力机组运行的环境要求。高升阻比、低粗糙度影响是该翼型族的气动性能特点。为了发展我国具有自主知识产权的风力机专用翼型族,在科技部863项目的支持下,北京航空航天大学联合国内气动研究单位,通过理论分析、数值模拟和风洞试验等技术途径,开发了两个适用于大型风力机组叶片的先进翼型族。理论分析和风洞试验表明,设计结果基本达到了预先设定的气动性能指标。     

椭球台高杆灯风荷载的实验研究

通过风洞实验研究了多钝体高杆灯在不同水平风向角和竖向风向角下的力与力矩系数。实验结果表明在一定的风向角下，法向阻力系数Cdmax=1.030,法向弯曲力矩系数Cmmax=-0.940,轴向力系数Camax=0.504和Camin=-0．600。     

飞翼模型高速风洞PIV试验研究

对小展弦比飞翼标模在2.4米跨声速风洞中创新开展了PIV试验。对空风洞进行了测速校核,并对小展弦比飞翼标模开展了二维、三维涡迹PIV测试,试验马赫数为0.4~0.9。测试结果表明,2.4m风洞PIV试验数据具有较高的准确度,M≤0.8时空风洞测速结果与理论值相差不超过1%,M=0.9时相差不超过2%。小展弦比飞翼标模测试结果显示,M数增大使机翼尾涡涡量和切向速度增大,涡核向内展向方向移动。前缘涡与上翼面分离具有密切关系:当M=0.8、α≤12°时,翼梢测试截面的前缘涡尚未破裂,上翼面未发生显著的流动分离;当α≥13°时,前缘涡破碎时机提前,当地后1/2弦长区域产生了比较明显的流动分离。