反射面天线的双站雷达截面

 本文导出了任意旋转反射器天线在任意双站角的散射场和雷达截面(RCS),其中反射场由几何光学法(GO)求得,绕射场则利用基于物理绕射理论(PTD)与等效线电流辐射积分公式导出的等效电磁流法求得。分别计算了轴向入射和偏轴向入射时在任意散射方向上水平极化与垂直极化两种情况下的双站RCS,并给出了这些结果的立体图形式。方法简化为单站情况时的计算结果与实验值大致相符。     

飞机在有源干扰保护下的探测概率研究

研究了飞机与雷达探测系统遭遇时，雷达对飞机的探测概率随距离的变化问题，采用X^2类目标波动模型，针对飞机在有源干扰保护的情况对探测概率随距离的变化进行了研究，对不同RCS对探测概率的影响问题进行了分析，研究结果可为飞机的雷达探测敏感性评估，飞机生存力的定量化分析与权衡，以及雷达探测系统的效能评估提供量化依据。     

微波暗室内雷达散射截面自动测量系统

介绍了微波暗室内雷达散射截面自动测量系统。主要包括同步转角信号的Ａ／Ｄ转，ＲＣＳ值的同步采集与处理以及转台的自动控制等部分，该系统具有１／３６度的定位精度和２．５ｍＶ的回波电压分辨率，系统误差小于１ｄＢ，适用于ＲＣＳ、天线方向性图及电磁兼容等测量。     

不同进口截面下液力透平非定常压力脉动计算

为了研究不同进口截面对液力透平内压力脉动的影响,利用CFX软件对一单级液力透平进行非定常数值计算,通过设置监测点,计算各监测点在不同进口截面下的压力脉动,通过快速傅里叶变换将其压力脉动计算结果做相应分析,分析各监测点处压力脉动的时域和频域分布.结果表明:蜗壳内在大蜗壳进口下,随着蜗壳进口直径的增加,每个监测点处的压力逐渐增加,而在小蜗壳进口下,每个监测点处的压力逐渐减小.在距离蜗壳收缩管较远处,大蜗壳进口下的压力脉动较小,而在距离收缩管较近处,小蜗壳进口下的压力脉动较小.在叶轮内不同进口截面压力脉动的差异在同一时刻从进口到出口逐渐减小.尾水管内在小蜗壳进口下尾水管进口处的压力脉动最大.      

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.     

Evolution of periodic orbits near the Lagrangian point L2

A study of the evolution of the periodic and the quasi-periodic orbits near the Lagrangian point L₂, which is located to the right of the smaller primary on the line joining the primaries and whose distance from the more massive primary is greater than the distance between the primaries, in the framework of restricted three-body problem for the Sun–Jupiter, Earth–Moon (relatively large mass ratio) and Saturn–Titan (relatively small mass ratio) systems is made. Two families of periodic orbits around the smaller primary are identified using the Poincaré surface of section method – family I (initially elliptical, gradually becomes egg-shaped with the increase in the Jacobi constant C and elongated towards the more massive primary) and family II (initially egg-shaped orbits elongated towards L₂ and gradually becomes elliptical with the increase in C). The family I in the Sun–Jupiter and Saturn–Titan systems contains two separatrix caused by third-order and fourth-order resonances, while the Earth–Moon system has only one separatrix which is caused by third-order resonances. Also in the Sun–Jupiter and the Saturn–Titan systems, family I merge with family II, around Jacobian constant 3.0393 and 3.0163, respectively, while in the Earth–Moon system, family II evolves separately from two different branches. The two branches merge at C = 3.184515. In the Earth–Moon system, the family II contains a separatrix due to third-order resonances which is absent in the other two systems.     

锯齿扁管内沸腾换热试验

建立以等热流密度方式进行试验件加热的沸腾换热试验系统,分别对当量直径为1.28mm和1.59mm锯齿扁管内R134a工质的沸腾换热特性进行研究,试验参数范围:制冷剂质量流率为68.5~305.5kg/(m2·s),工作饱和压力为0.27~0.46 MPa,加热热流密度为9~42kW/m2。试验结果表明:相同结构的通道,当量直径小换热能力更强;热流密度和饱和压力对沸腾换热的影响与一个干度值有关。当干度小于此值时,沸腾换热系数会随着热流密度及饱和压力增大而增大;而当干度大于此值时,沸腾换热系数随着干度增大而急剧下降,热流密度和饱和压力对换热的影响较小;该干度值会随着热流密度或饱和压力增大而逐渐变小。质量流率对沸腾换热的影响与热流密度有关,随着热流密度增大,质量流率的影响趋向大干度区域。通过分析各参数对沸腾换热的影响,建立了一个预测试验工况下微小尺寸锯齿扁管的沸腾换热系数计算经验公式。     

长矩形盒零件超塑性胀形工艺加载规律的优化

本文通过对长矩形盒零件的力学解析，得到了优化加载规律的数学表达形式。按此规律进行气压胀形，与恒压胀形实验结果相比，能有效地提高成形极限，并使厚度分布情况有明显的改善。     

隐身目标电磁散射特性的图形电磁计算方法研究

计算了不同涂覆介质的反射系数,利用图形电磁计算方法计算了平板和圆柱的涂覆不同介质的雷达散射截面,并且为了增加图形电磁计算的通用性引入了归一化因子。结果表明,此计算方法是正确的。     

闭合薄壁剖面杆刚度计算的有限元素法

利用有限元法对飞机闭合薄壁剖面杆结构进行刚度计算，其结果与全尺寸试验值吻合较好。